Page 1
Patriot 2 0 1 2 O W N E R ’ S M A N U A L...
Page 2
VEHICLES SOLD IN CANADA With respect to any Vehicles Sold in Canada, the name This manual illustrates and describes the operation of fea- Chrysler Group LLC shall be deemed to be deleted and the tures and equipment that are either standard or optional on name Chrysler Canada Inc.
4 INTRODUCTION INTRODUCTION When it comes to service, remember that your authorized Congratulations on selecting your new Chrysler Group dealer knows your vehicle best, has factory-trained tech- LLC vehicle. Be assured that it represents precision nicians and genuine MOPAR parts, and cares about workmanship, distinctive styling, and high quality - all your satisfaction.
INTRODUCTION 5 control. Failure to operate this vehicle safely may result seat belts could cut the highway death toll by 10,000 or in a collision, rollover of the vehicle, and severe or fatal more each year and could reduce disabling injuries by injury.
INTRODUCTION 7 WARNINGS AND CAUTIONS This Owner’s Manual contains WARNINGS against op- erating procedures that could result in a collision or bodily injury. It also contains CAUTIONS against proce- dures that could result in damage to your vehicle. If you do not read this entire manual, you may miss important information.
8 INTRODUCTION VEHICLE MODIFICATIONS/ALTERATIONS WARNING! Any modifications or alterations to this vehicle could seriously affect its roadworthiness and safety and may lead to a accident resulting in serious injury or death. Right Front Body VIN Location NOTE: It is illegal to remove or alter the VIN.
Page 11
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE CONTENTS A Word About Your Keys ....12 Vehicle Security Alarm — If Equipped ..18 Ignition Key Removal .
Page 12
10 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Illuminated Approach — If Equipped ..21 Child-Protection Door Lock System — Rear Doors ......33 To Lock The Doors And Liftgate .
Page 13
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 11 Automatic Locking Retractor Mode (ALR) — Air Bag Deployment Sensors And Controls . . . 67 If Equipped ......53 Event Data Recorder (EDR) .
12 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE A WORD ABOUT YOUR KEYS Ignition Key Removal The authorized dealer that sold you your new vehicle has 1. Place the shift lever in PARK (if equipped with an the key code numbers for your vehicle locks. These automatic transmission).
Page 15
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 13 NOTE: If you try to remove the key before you place the shift lever in PARK, the key may become trapped tem- porarily in the ignition switch cylinder. If this occurs, place the shift lever in PARK, rotate the key to the right slightly, then remove the key as described.
14 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) CAUTION! • Allowing children to be in a vehicle unattended is An unlocked car is an invitation to thieves. Always dangerous for a number of reasons. A child or remove the key from the ignition and lock all the others could be seriously or fatally injured.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 15 SENTRY KEY seconds for a bulb check. If the light remains on after the The Sentry Key Immobilizer System prevents unauthor- bulb check, it indicates that there is a problem with the ized vehicle operation by disabling the engine.
16 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE All of the keys provided with your new vehicle have required for authorized dealer replacement of keys. Du- been programmed to the vehicle electronics. plication of keys may be performed at an authorized dealer or by following the customer key programming Replacement Keys procedure.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 17 2. Insert the first valid key into the ignition switch. Turn The new Sentry Key is programmed. The Remote the ignition switch to the ON/RUN position for at least Keyless Entry (RKE) transmitter will also be pro- three seconds, but no longer than 15 seconds.
18 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • This device must accept any interference that may be To Arm The System received, including interference that may cause unde- 1. Remove the key from the ignition switch and get out sired operation.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 19 Rearming The System If something has triggered the Vehicle Security Alarm in If something triggers the alarm, and no action is taken to your absence, the horn will sound three times and disarm it, the Vehicle Security Alarm will turn off the exterior lights blink three times when you unlock the horn after three minutes, turn off all of the visual signals...
20 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE REMOTE KEYLESS ENTRY (RKE) — IF EQUIPPED NOTE: The line of transmission must not be blocked This system allows you to lock or unlock the doors and with metal objects. liftgate or activate the Panic Alarm from distances up to To Unlock The Doors And Liftgate approximately 66 ft (20 m) using a hand-held Remote Press and release the UNLOCK button on the RKE...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 21 • For vehicles not equipped with the EVIC, perform the Security Alarm activated will cause the alarm to sound. following steps: Press the UNLOCK button to deactivate the Vehicle Security Alarm. 1. Press and hold the LOCK button on a programmed RKE transmitter for at least 4 seconds, but no longer than Illuminated Approach —...
22 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For vehicles not equipped with the EVIC, perform the To Lock The Doors And Liftgate Press and release the LOCK button on the RKE transmit- following steps: ter to lock all doors and liftgate. The turn signal lights 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 23 • For vehicles not equipped with the EVIC, perform the NOTE: Pressing the LOCK button on the RKE transmit- ter while you are in the vehicle will activate the Vehicle following steps: Security Alarm.
24 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Alarm activated will cause the alarm to sound. Press the Programming Additional Transmitters UNLOCK button to deactivate the Vehicle Security Refer to Sentry Key “Customer Key Programming.” Alarm. If you do not have a programmed RKE transmitter, Using The Panic Alarm contact your authorized dealer for details.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 25 If your RKE transmitter fails to operate from a normal distance, check for these two conditions: 1. Weak battery in the RKE transmitter. The expected life of a battery is five years. 2.
26 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. To reassemble the RKE transmitter case, snap the two How To Use Remote Start halves together. All of the following conditions must be met before the engine will remote start: NOTE: If the RKE transmitter is equipped with a screw, •...
Page 29
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 27 • Remote Start Aborted — Hood Ajar WARNING! • Remote Start Aborted — L/Gate Ajar • Do not start or run an engine in a closed garage or • Remote Start Aborted — Fuel Low confined area.
Page 30
28 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • For security, power window and power sunroof op- • The hood is opened eration (if equipped) are disabled when the vehicle is • The hazard switch is pressed in the Remote Start mode. •...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 29 To Exit Remote Start Mode And Drive The Vehicle Before the end of the 15-minute cycle, press and release the UNLOCK button on the RKE transmitter to unlock the doors and disarm the Vehicle Security Alarm (if equipped).
30 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! (Continued) CAUTION! • Before exiting a vehicle, always apply the parking An unlocked vehicle is an invitation to thieves. brake, shift the transmission into PARK, and re- Always remove the key from the ignition and lock all move the key fob from the ignition.
Page 33
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 31 auto door lock feature can be enabled or disabled by your authorized dealer. Please see your authorized dealer for service. Auto Lock Doors Programming The Automatic Door Locks feature can be enabled or disabled as follows: •...
Page 34
32 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 2. Within 15 seconds, cycle the ignition switch between Automatic Unlock Doors On Exit LOCK and ON/RUN and then back to LOCK four times The doors will unlock automatically if: ending up in the LOCK position (do not start the engine). 1.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 33 Equipped/ Personal Settings (Customer-Programmable NOTE: • If you do not hear the chime it means that the system Features)” in “Understanding Your Instrument Panel” for further information. did not enter the programming mode and you will need to repeat the procedure.
Page 36
34 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Repeat steps 1 and 2 for the opposite rear door. Child-Protection Door Lock Function Child-Protection Door Lock Location WARNING! Avoid trapping anyone in a vehicle in a collision. Remember that the rear doors can only be opened from the outside when the Child-Protection locks are engaged.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 35 NOTE: For emergency exit with the system engaged, NOTE: • For vehicles not equipped with the Electronic Vehicle move the lock knob up (unlocked position), roll down the window and open the door with the outside door handle. Information Center (EVIC), the power window switches will remain active for 45 seconds after the POWER WINDOWS —...
36 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE WARNING! Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unattended children, can become entrapped by the windows while operating the power window switches. Such entrapment may result in serious injury or death. Power Window Switch Location Auto-Down The driver’s door window switch has an Auto-Down...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 37 Window Lockout Switch LIFTGATE The window lockout switch on the driver’s door allows NOTE: The key that is used to start the vehicle is also you to disable the window control on the other doors. To used to lock or unlock the doors and open the liftgate.
Page 40
38 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Once unlocked, the liftgate can be opened or closed NOTE: • In the event of a power malfunction, or the RKE without using the key. To open the liftgate, squeeze the liftgate release and pull the liftgate open with one fluid transmitter is inoperative, insert the key into the motion.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 39 • Supplemental Active Head Restraints (AHR) located WARNING! (Continued) on top of the front seats (integrated into the head • If you are required to drive with the liftgate open, restraint) — if equipped make sure that all windows are closed, and the •...
Page 42
40 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE seat belt webbing into position by extending the belt Here are some simple steps you can take to minimize the all the way out and then adjusting the belt to the risk of harm from a deploying air bag: desired length to restrain a child seat or secure a large 1.
Page 43
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 41 ride properly buckled up in the rear seat. Never allow 4. Do not lean against the door or window. If your children to slide the shoulder belt behind them or under vehicle has side air bags, and deployment occurs, the their arm.
42 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Buckle up even though you are an excellent driver, even WARNING! (Continued) on short trips. Someone on the road may be a poor driver • Being too close to the steering wheel or instrument and cause an accident that includes you.
Page 45
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 43 The belt webbing retractor is designed to lock during WARNING! (Continued) very sudden stops or accidents. This feature allows the • Wearing a seat belt incorrectly is dangerous. Seat shoulder part of the belt to move freely with you under belts are designed to go around the large bones of normal conditions.
Page 46
44 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Lap/Shoulder Belt Operating Instructions 1. Enter the vehicle and close the door. Sit back and adjust the seat. 2. The seat belt latch plate is along side the pillar near the back of your seat. Grasp the latch plate and pull out the belt.
Page 47
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 45 3. When the belt is long enough to fit, insert the latch WARNING! plate into the buckle until you hear a “click.” • A belt that is buckled into the wrong buckle will not protect you properly.
Page 48
46 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 4. Position the lap belt across your thighs, below your WARNING! (Continued) abdomen. To remove slack in the lap belt portion, pull up • A belt that is worn under your arm is dangerous. on the shoulder belt.
Page 49
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 47 6. To release the belt, push the red button on the buckle. WARNING! The belt will automatically retract to its stowed position. • A lap belt worn too high can increase the risk of If necessary, slide the latch plate down the webbing to allow the belt to retract fully.
48 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Adjustable Upper Shoulder Belt Anchorage In the front seat, the shoulder belt can be adjusted upward or downward to position the belt away from your neck. Push the anchorage button to release the anchorage, and move it up or down to the position that fits you best.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 49 In the rear seat, move toward the center of the seat to position the belt away from your neck. Second Row Center Lap/Shoulder Belt Operating Instructions The second row center lap/shoulder belt features a three-point seat belt with a mini-latch and buckle, which allows the shoulder belt to detach from the lower anchor when the seat is folded.
Page 52
50 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Route the shoulder belt to the inside of the right head 5. Sit back in the seat. Slide the regular latch plate up the restraint. webbing as far as necessary to allow the belt to go around your lap.
Page 53
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 51 7. Position the lap belt across your thighs, below your 8. Position the shoulder belt on your chest so that it is abdomen. To remove slack in the lap belt portion, pull up comfortable and not resting on your neck.
52 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 10. To disengage the mini-latch from the mini-buckle for 3. Slide the latch plate upward over the folded webbing. storage, insert the regular latch plate into the black The folded webbing must enter the slot at the top of the button on the top of the mini-buckle.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 53 Automatic Locking Retractor Mode (ALR) — If Driver Center Passenger Equipped First Row In this mode, the shoulder belt is automatically pre- Second Row locked. The belt will still retract to remove any slack in •...
54 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE How To Engage The Automatic Locking Mode WARNING! 1. Buckle the combination lap and shoulder belt. • The belt and retractor assembly must be replaced 2. Grasp the shoulder portion and pull downward until if the seat belt assembly Automatic Locking Re- the entire belt is extracted.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 55 Seat Belt Pretensioners Supplemental Active Head Restraints (AHR) — If The seat belts for both front seating positions are Equipped equipped with pretensioning devices that are designed to These head restraints are passive, deployable compo- remove slack from the seat belt in the event of an nents, and vehicles with this equipment cannot be readily accident.
Page 58
56 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE When AHRs deploy during a rear impact, the front half of the head restraint extends forward to minimize the gap between the back of the occupant’s head and the AHR. This system is designed to help prevent or reduce the extent of injuries to the driver and front passenger in certain types of rear impacts.
Page 59
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 57 1. Grasp the deployed AHR from the rear seat. CAUTION! All occupants, including the driver, should not oper- ate a vehicle or sit in a vehicle’s seat until the head restraints are placed in their proper positions in order to minimize the risk of neck injury in the event of an accident.
Page 60
58 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 3. Pull down then rearward towards the rear of the vehicle then down to engage the locking mechanism. 3 — Final Downward Movement To Engage Locking Mechanism 1 — Downward Movement 2 — Rearward Movement...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 59 4. The AHR front soft foam and trim half should lock Enhanced Seat Belt Use Reminder System into the back decorative plastic half. (BeltAlert ) BeltAlert is a feature intended to remind the driver and front passenger (if equipped with front passenger BeltAlert ) to fasten their seat belts.
60 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE unbuckled while traveling at speeds greater than 5 mph Seat Belt Extender (8 km/h), BeltAlert will provide both audio and visual If a seat belt is too short, even when fully extended, and notification.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 61 Seat Belts And Pregnant Women We recommend that pregnant women use the seat belts throughout their pregnancy. Keeping the mother safe is the best way to keep the baby safe. Pregnant women should wear the lap part of the belt across the thighs and as snug across the hips as possible.
Page 64
62 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The Advanced Front Air Bags have a multistage inflator This vehicle may be equipped with Supplemental Seat- design. This allows the air bag to have different rates of Mounted Side Air Bags (SAB) to provide enhanced inflation that are based on the severity and type of protection for an occupant during a side impact.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 63 • Instrument Panel Advanced Front Air Bag Features The Advanced Front Air Bag system has multistage • Knee Impact Bolster driver and front passenger air bags. This system provides • Driver Advanced Front Air Bag output appropriate to the severity and type of collision as determined by the Occupant Restraint Controller (ORC), •...
Page 66
64 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Supplemental Seat-Mounted Side Air Bags WARNING! (SAB) — If Equipped • No objects should be placed over or near the air Supplemental Seat-Mounted Side Air Bags (SAB) may bag on the instrument panel, because any such provide enhanced protection to help protect an occupant objects could cause harm if the vehicle is in a during a side impact.
Page 67
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 65 When the air bag deploys, it opens the seam between the front and side of the seat’s trim cover. Each air bag deploys independently; a left side impact deploys the left air bag only and a right-side impact deploys the right air bag only.
Page 68
66 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Being too close to the Supplemental Side Air Bag WARNING! (Continued) Inflatable Curtain and/or Seat-Mounted Side Air Bag • Do not use accessory seat covers or place objects during deployment could cause you to be severely between you and the side air bags;...
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 67 Along with seat belts and pretensioners, Advanced Front Advanced Front Air Bags are designed to provide addi- Air Bags work with the knee bolsters to provide im- tional protection by supplementing the seat belts in proved protection for the driver and front passenger.
Page 70
68 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Because air bag sensors measure vehicle deceleration Also, the ORC turns on the Air Bag Warning over time, vehicle speed and damage by themselves are Light in the instrument panel for approxi- not good indicators of whether or not an air bag should mately four to eight seconds for a self-check have deployed.
Page 71
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 69 are possible, based on the collision type and severity. The WARNING! steering wheel hub trim cover and the upper right side of the instrument panel separate and fold out of the way as Ignoring the Air Bag Warning Light in your instru- the air bags inflate to their full size.
Page 72
70 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Based on the severity and type of collision, the side air A quantity of non-toxic gas is generated to inflate the side bag inflator on the crash side of the vehicle may be curtain air bag.
Page 73
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 71 • Turn on the interior lights, which remain on as long as Front And Side Impact Sensors In front and side impacts, impact sensors can aid the the battery has power or until the ignition key is ORC in determining appropriate response to impact removed.
Page 74
72 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE If you do have a collision, which deploys the air bags, any throat irritation, move to fresh air. If the irritation or all of the following may occur: continues, see your doctor. If these particles settle on your clothing, follow the garment manufacturer’s in- •...
Page 75
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 73 Maintaining Your Air Bag System WARNING! (Continued) • Do not attempt to modify any part of your air bag WARNING! system. The air bag may inflate accidentally or • Modifications to any part of the air bag system may not function properly if modifications are could cause it to fail when you need it.
74 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Air Bag Warning Light NOTE: If the speedometer, tachometer, or any engine You will want to have the air bags ready to related gauges are not working, the Occupant Restraint inflate for your protection in a collision. The Controller (ORC) may also be disabled.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 75 • Whether or not the driver and passenger safety belts To read data recorded by an EDR, special equipment is were buckled/fastened; required, and access to the vehicle or the EDR is needed. In addition to the vehicle manufacturer, other parties, •...
Page 78
76 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE The infant carrier is only used rearward-facing in the WARNING! vehicle. It is recommended for children from birth until they reach the weight or height limit of the infant carrier. In a collision, an unrestrained child, even a tiny baby, Convertible child seats can be used either rearward- can become a projectile inside the vehicle.
Page 79
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 77 in the vehicle by the lap/shoulder belt or the LATCH WARNING! child restraint anchorage system. Refer to “Lower An- chors and Tether for CHildren (LATCH)”. Rearward-facing child seats must never be used in the front seat of a vehicle with the front passenger air All children whose weight or height is above the bag unless the air bag is turned off.
Page 80
78 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE you make sure that you can install the child restraint in WARNING! the vehicle where you will use it, before you buy it. • Improper installation can lead to failure of an •...
Page 81
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 79 retractor. For additional information on ALR, refer to retracts, you will hear a ratcheting sound. This indicates “Automatic Locking Mode”. The chart below defines the the safety belt is now in the Automatic Locking mode. seating positions with an Automatic Locking Retractor 2.
Page 82
80 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE • Make sure that the child is upright in the seat. around, and insert the latch plate into the buckle again. If you still can’t make the child restraint secure, • The lap portion should be low on the hips and as snug try a different seating position.
Page 83
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 81 webbing-mounted lower attachments. Child seats with fixed lower attachments must be installed in the out- board positions only. Regardless of the specific type of lower attachment, never install LATCH-compatible child seats such that two seats share a common lower anchor- age.
Page 84
82 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE provide add-on tether strap kits for some of their older restraint installation, instead of tucking the seat belt products. Tether anchorage kits are also available for behind the child restraint, route the seat belt through the most older vehicles.
Page 85
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 83 In general, you will first loosen the adjusters on the lower Not all child restraint systems will be installed as we and tether straps so that you can attach the hook or have described here.
84 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Transporting Pets The engine oil installed in the engine at the factory is a Air Bags deploying in the front seat could harm your pet. high-quality energy conserving type lubricant. Oil An unrestrained pet will be thrown about and possibly changes should be consistent with anticipated climate injured, or injure a passenger during panic braking or in conditions under which vehicle operations will occur.
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 85 SAFETY TIPS Exhaust Gas Transporting Passengers WARNING! NEVER TRANSPORT PASSENGERS IN THE CARGO AREA. Exhaust gases can injure or kill. They contain carbon monoxide (CO), which is colorless and odorless. WARNING! Breathing it can make you unconscious and can •...
86 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE Safety Checks You Should Make Inside The WARNING! (Continued) Vehicle • If it is necessary to sit in a parked vehicle with the Seat Belts engine running, adjust your heating or cooling Inspect the belt system periodically, checking for cuts, controls to force outside air into the vehicle.
Page 89
THINGS TO KNOW BEFORE STARTING YOUR VEHICLE 87 Defroster WARNING! (Continued) Check operation by selecting the defrost mode and place • Always make sure that floor mats are properly the blower control on high speed. You should be able to attached to the floor mat fasteners.
88 THINGS TO KNOW BEFORE STARTING YOUR VEHICLE lodged in the tread or sidewall. Inspect the tread for cuts WARNING! (Continued) and cracks. Inspect sidewalls for cuts, cracks and bulges. • Always make sure that objects cannot fall into the Check the wheel nuts for tightness.
94 UNDERSTANDING THE FEATURES OF YOUR VEHICLE MIRRORS Inside Day/Night Mirror A two-point pivot system allows for horizontal and vertical mirror adjustment. Adjust the mirror to center on the view through the rear window. Headlight glare can be reduced by moving the small control under the mirror to the night position (toward the rear of vehicle).
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 95 Automatic Dimming Mirror — If Equipped CAUTION! This mirror automatically adjusts for headlight glare from vehicles behind you. You can turn the feature on or To avoid damage to the mirror during cleaning, never off by pressing the button at the base of the mirror.
96 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Power Mirrors To adjust a mirror, turn the control wand toward the left The power mirror controls are located on the driver’s or right mirror positions indicated. Tilt the control wand door trim panel. in the direction you want the mirror to move.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 97 Outside Mirror — Driver Side Outside Mirror — Passenger Side Adjust the flat outside mirror to center on the adjacent Adjust the convex outside mirror to center on the adja- lane of traffic with a slight overlap of the view obtained cent lane of traffic with a slight overlap of the view on the inside mirror.
98 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Vehicles and other objects seen in the passenger side convex mirror will look smaller and farther away than they really are. Relying too much on your passenger side mirror could cause you to collide with another vehicle or other object.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 99 Vanity Mirrors — If Equipped Uconnect™ Phone — IF EQUIPPED To use the mirror, pull the sun visor down and rotate the Uconnect™ Phone is a voice-activated, hands-free, in- mirror cover upward. vehicle communications system. Uconnect™ Phone al- lows you to dial a phone number with your mobile phone using simple voice commands (e.g., “Call”...
Page 102
100 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • www.jeep.com/uconnect system. Only one linked (or paired) mobile phone can be used with the system at a time. The system is available in • or call 1–877–855–8400 English, Spanish, or French languages.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 101 Voice Command Button Operation Actual button location may vary with the ra- Voice commands can be used to operate the Uconnect™ dio. The individual buttons are described in the Phone and to navigate through the Uconnect™ Phone “Operation”...
Page 104
102 UNDERSTANDING THE FEATURES OF YOUR VEHICLE example, you can use the compound form voice Cancel Command command “Phonebook New Entry”, or you can break At any prompt, after the beep, you can say “Cancel” and the compound form command into two voice com- you will be returned to the main menu.
Page 105
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 103 • When prompted, after the beep, say “Pair a Device” phone to use if multiple mobile phones are in the and follow the audible prompts. vehicle at the same time. For example, if priority three and priority five phones are present in the vehicle, the •...
Page 106
104 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The Uconnect™ Phone will confirm the phone number • The Uconnect™ system will confirm the name and and then dial. The number will appear in the display then dial the corresponding phone number, which of certain radios.
Page 107
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 105 • When prompted, enter the number designation (e.g., Phonebook Download – Automatic Phonebook “Home”, “Work”, “Mobile”, or “Other”). This will Transfer From Mobile Phone allow you to store multiple numbers for each phone- If equipped and specifically supported by your phone, book entry, if desired.
Page 108
106 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • Depending on the maximum number of entries down- Edit Uconnect™ Phonebook Entries loaded, there may be a short delay before the latest NOTE: downloaded names can be used. Until then, if avail- •...
Page 109
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 107 • After you enter the Phonebook Delete menu, you will After you are finished editing an entry in the phonebook, you will be given the opportunity to edit another entry in then be asked for the name of the entry that you wish the phonebook, call the number you just edited, or return to delete.
Page 110
108 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Delete/Erase “All” Uconnect™ Phonebook Entries List All Names In The Uconnect™ Phonebook • Press the • Press the button to begin. button to begin. • After the “Ready” prompt and the following beep, say •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 109 Phone Call Features Answer Or Reject An Incoming Call — Call The following features can be accessed through the Currently In Progress Uconnect™ Phone if the feature(s) are available on your If a call is currently in progress and you have another mobile service plan.
Page 112
110 UNDERSTANDING THE FEATURES OF YOUR VEHICLE in progress. To go back to the first call, refer to “Toggling Conference Call Between Calls” in this section. To combine two calls, refer When two calls are in progress (one active and one on to “Conference Call”...
Page 113
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 111 Call Termination Call Continuation To end a call in progress, momentarily press the Call continuation is the progression of a phone call on the button. Only the active call(s) will be terminated and if Uconnect™...
112 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Uconnect™ Phone Features Emergency Assistance If you are in an emergency and the mobile phone is Language Selection reachable: To change the language that the Uconnect™ Phone is • Pick up the phone and manually dial the emergency using: number for your area.
Page 115
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 113 Canada and 060 for Mexico). The number dialed may Towing Assistance not be applicable with the available mobile service and If you need towing assistance: area. • Press the button to begin. • If supported, this number may be programmable on •...
Page 116
114 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Paging When calling a number with your Uconnect™ Phone that To learn how to page, refer to “Working with Automated normally requires you to enter in a touch-tone sequence Systems”. Paging works properly except for pagers of on your mobile phone keypad, you can press the certain companies, which time out a little too soon to button and say the sequence you wish to enter, followed...
Page 117
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 115 The Uconnect™ Phone will then send the corresponding Turning Confirmation Prompts ON/OFF phone number associated with the phonebook entry, as Turning confirmation prompts off will stop the system tones over the phone. from confirming your choices (e.g., the Uconnect™ Phone will not repeat a phone number before you dial it).
116 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Dialing Using The Mobile Phone Keypad Mute/Un-Mute (Mute OFF) You can dial a phone number with your mobile phone When you mute the Uconnect™ Phone, you will still be keypad and still use the Uconnect™ Phone (while dialing able to hear the conversation coming from the other via the mobile phone keypad, the user must exercise party, but the other party will not be able to hear you.
Page 119
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 117 • When prompted, say “List Phones”. from your Uconnect™ Phone paired mobile phone to the Uconnect™ Phone or vice versa, press the button • The Uconnect™ Phone will play the phone names of and say “Transfer Call”.
118 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • The selected phone will be used for the next phone Things You Should Know About Your Uconnect™ call. If the selected phone is not available, the Phone Uconnect™ Phone will return to using the highest Uconnect™...
Page 121
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 119 You can either press the Uconnect™ Phone button to Voice Command restore the factory setting or repeat the words and • For best performance, adjust the rearview mirror to phrases when prompted by the Uconnect™ Phone. For provide at least ⁄...
Page 122
120 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • fully closed windows, • Numbers must be spoken in single digits. “800” must be spoken “eight-zero-zero” not “eight hundred”. • dry weather condition. • You can say “O” (letter “O”) for “0” (zero). •...
Page 123
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 121 • fully closed windows, Uconnect™ Phone can read or send new messages on • dry weather conditions, and your phone. • operation from the driver’s seat. Read Messages: • Performance, such as audio clarity, echo, and loudness If you receive a new text message while your phone is to a large degree rely on the phone and network, and connected to Uconnect™...
Page 124
122 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Send Messages: 3. Where are you? You can send messages using Uconnect™ Phone. To send 4. I need more direction. a new message: 5. L O L • Press the button. 6. Why •...
Page 125
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 123 16. Can this wait? Bluetooth Communication Link Mobile phones have been found to lose connection to the 17. Bye for now Uconnect™ Phone. When this happens, the connection 18. When can we meet can generally be reestablished by switching the phone off/on.
Page 126
124 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 127
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 125...
Page 128
126 UNDERSTANDING THE FEATURES OF YOUR VEHICLE...
Page 129
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 127 Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) zero call cancel confirmation prompts three continue four delete five dial download seven edit eight emergency nine English star (*) erase all plus (+) Espanol pound (#) Francais add location...
Page 130
128 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Commands Voice Commands Primary Alternate(s) Primary Alternate(s) language return to main menu return or main menu list names select phone select list phones send mobile set up phone settings or phone set up mute towing assistance mute off...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 129 General Information NOTE: Take care to speak into the Voice Interface This device complies with Part 15 of the FCC rules and System as calmly and normally as possible. The ability of RSS 210 of Industry Canada. Operation is subject to the the Voice Interface System to recognize user voice com- following conditions: mands may be negatively affected by rapid speaking or a...
130 UNDERSTANDING THE FEATURES OF YOUR VEHICLE If you ever wish to interrupt the system while it lists The system will best recognize your speech if the win- options, press the Voice Command button, listen dows are closed, and the heater/air conditioning fan is for the beep, and say your command.
Page 133
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 131 3. Use the ON/OFF VOLUME rotary knob to adjust the Radio AM volume to a comfortable level while the Voice Command To switch to the AM band, say “AM” or “Radio AM”. In system is speaking.
Page 134
132 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • “Menu Radio” (to switch to the radio menu) Disc To switch to the disc mode, say “Disc”. In this mode, you • “Main Menu” (to switch to the main menu) may say the following commands: Satellite Radio •...
Page 135
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 133 • “Switch to system setup” − “Continue” (to continue recording) • “Change to setup” − “Delete” (to delete the recording) • “Play Memos” (to play previously recorded memos) • “Main menu setup” or —...
134 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Voice Training SEATS For users experiencing difficulty with the system recog- Seats are a part of the Occupant Restraint System of the nizing their voice commands or numbers the Uconnect™ vehicle. Voice “Voice Training” feature may be used. WARNING! 1.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 135 Power Seats — If Equipped WARNING! Some models may be equipped with a power driver’s • Adjusting a seat while driving may be dangerous. seat. The power seat switch is located on the outboard side of the seat near the floor.
136 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Adjusting The Seat Forward Or Rearward Heated Seats — If Equipped The seat can be adjusted both forward and rearward. On some models, the front driver and passenger seats Push the seat switch forward or rearward, the seat will may be equipped with heaters in both the seat cushions move in the direction of the switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 137 If HIGH-level heating is selected, the system automati- WARNING! cally switches to LOW-level heating and turns one indi- • Persons who are unable to feel pain to the skin cator light OFF after a maximum of 60 minutes of continuous operation.
Page 140
138 UNDERSTANDING THE FEATURES OF YOUR VEHICLE While sitting in the seat, lift up on the bar and move the WARNING! seat forward or rearward. Release the bar once you have • Adjusting a seat while driving may be dangerous. reached the desired position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 139 Manual Seat Height Adjustment — If Equipped Manual Lumbar — If Equipped The driver’s seat height can be raised or lowered by using The lumbar adjustment handle is located on the outboard a lever, located on the outboard side of the seat. Pull side of the driver’s seatback.
140 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Driver’s Seatback Recline WARNING! To adjust the seatback, lift the lever located on the outboard side of the seat, lean back to the desired angle Do not ride with the seatback reclined so that the and release the lever.
Page 143
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 141 Fold-Flat Front Passenger Seat Lever Front Passenger Seat Folded Flat...
142 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Head Restraints Active Head Restraints — Front Seats Head restraints are designed to reduce the risk of injury Active Head Restraints are passive, deployable compo- by restricting head movement in the event of a rear nents, and vehicles with this equipment cannot be readily impact.
Page 145
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 143 To raise the head restraint, pull upward on the head For comfort the Active Head Restraints can be tilted restraint. To lower the head restraint, press the push forward and backward. To tilt the head restraint closer to button, located at the base of the head restraint, and push the back of your head, pull forward on the bottom of the downward on the head restraint.
Page 146
144 UNDERSTANDING THE FEATURES OF YOUR VEHICLE • In the event of deployment of an Active Head Re- straint, refer to “Occupant Restraints/Resetting Active Head Restraints (AHR)” in “Things To Know Before Starting Your Vehicle” for further information. WARNING! • Do not place items over the top of the Active Head Restraint, such as coats, seat covers or portable DVD players.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 145 Folding Rear Seat WARNING! (Continued) To provide additional storage area, each rear seatback can • Active Head Restraints may be deployed if they be folded forward. Pull the strap forward to move the are struck by an object such as a hand, foot or loose seat forward and flat.
146 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Be certain that the seatback is securely locked into position. If the seatback is not securely locked into position the seat will not provide the proper stability for child seats and/or passengers. An improperly latched seat could cause serious injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 147 WARNING! Do not ride with the seatback reclined so that the shoulder belt is no longer resting against your chest. In a collision you could slide under the seat belt and be seriously or even fatally injured. Use the recliner only with the vehicle is parked.
Page 150
148 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 2. Move the safety catch located under the front edge of Lift the hood prop rod, clipped to the right side (left side the hood, near the center and raise the hood. facing hood) of the engine compartment, to secure the hood in the open position.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 149 LIGHTS CAUTION! Multifunction Lever To prevent possible damage, do not slam the hood to The multifunction lever controls the operation of the close it. Lower the hood until it is open approxi- headlights, parking lights, turn signals, headlight beam mately 8 in (20 cm) and then drop it.
150 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Headlights And Parking Lights Daytime Running Lights — If Equipped Turn the end of the multifunction lever to the first detent The high beam lights will come on as Daytime Running to turn on the parking lights. Lights (DRL) at DRL intensity (lower), whenever the ignition is ON, the engine is running, the headlight Turn the end of the lever to the second detent to turn on...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 151 Turn Signals Move the multifunction lever up or down and the arrows on each side of the instrument cluster flash to show proper operation of the front and rear turn signal lights. Front Fog Lights Control NOTE: The fog lights will only operate with the head- lights on low beam.
152 UNDERSTANDING THE FEATURES OF YOUR VEHICLE light bulb. If an indicator fails to light when the lever is NOTE: If the multifunction lever is held in the flash-to- moved, it would suggest that the indicator bulb is pass position for more than 20 seconds, the high beams defective.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 153 Dimmer Control Map/Reading Lights Map/Reading Lights NOTE: To protect the battery, the interior lights will turn These lights are mounted between the sun visors above off automatically 10 minutes after the ignition switch is the rear view mirror.
154 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WINDSHIELD WIPERS AND WASHERS CAUTION! The windshield wiper/washer control lever is • Turn the windshield wipers off when driving located on the right side of the steering column. The front wipers are operated by rotating a through an automatic car wash.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 155 Windshield Wiper Operation Rotate the end of the lever upward to the second detent past the intermittent settings for low-speed wiper opera- tion. Rotate the end of the lever upward to the third detent past the intermittent settings for high-speed wiper opera- tion.
156 UNDERSTANDING THE FEATURES OF YOUR VEHICLE downward (counterclockwise) to increase the delay time. WARNING! The delay can be regulated from a maximum of approxi- mately 18 seconds between cycles, to a cycle every Sudden loss of visibility through the windshield second.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 157 Push down on the lever to unlock the steering column. With one hand firmly on the steering wheel, move the steering column up or down, as desired. Push the lever up to lock the steering column firmly in place. Mist Control TILT STEERING COLUMN This feature allows you to tilt the steering column...
158 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! Do not adjust the steering column while driving. Adjusting the steering column while driving or driv- ing with the steering column unlocked, could cause the driver to lose control of the vehicle. Be sure the steering column is locked before driving your ve- hicle.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 159 System can be reactivated by pushing the Electronic To Set A Desired Speed Speed Control ON/OFF button and resetting the desired Turn the Electronic Speed Control ON. When the vehicle vehicle set speed. has reached the desired speed, press the SET (-) button and release.
160 UNDERSTANDING THE FEATURES OF YOUR VEHICLE To Resume Speed decrease until the button is released. Release the button To resume a previously set speed, push the RES (+) when the desired speed is reached, and the new set speed button and release.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 161 On steep hills, a greater speed loss or gain may occur so The HomeLink buttons, located on either the overhead it may be preferable to drive without Electronic Speed console, headliner or sunvisor, designate the three differ- Control.
162 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Before You Begin Programming HomeLink Be sure that your vehicle is parked outside of the garage before you begin programming. For more efficient programming and accurate transmis- sion of the radio-frequency signal it is recommended that a new battery be placed in the hand-held transmitter of the device that is being programmed to the HomeLink system.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 163 NOTE: • Erasing all channels should only be performed when programming HomeLink for the first time. Do not erase channels when programming additional buttons. • If you have any problems, or require assistance, please call toll-free 1–800–355–3515 or, on the Internet at www.HomeLink.com for information or assistance.
Page 166
164 UNDERSTANDING THE FEATURES OF YOUR VEHICLE 3. Simultaneously press and hold both the Homelink NOTE: You have 30 seconds in which to initiate the next button you want to program and the hand-held transmit- step after the LEARN button has been pressed. ter button.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 165 2. Press and hold the desired HomeLink button until 4. Continue to hold both buttons and observe the indi- the indicator light begins to flash after 20 seconds. Do not cator light. The Homelink indicator will flash slowly release the button.
166 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Reprogramming A Single HomeLink Button to pick up the signal during programming. Similar to this To reprogram a channel that has been previously trained, Canadian law, some U.S. gate operators are designed to follow these steps: time-out in the same manner.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 167 4. Watch for the HomeLink indicator to change flash Reprogramming A Single HomeLink Button rates. When it changes, it is programmed. It may take up To reprogram a channel that has been previously trained, to 30 seconds or longer in rare cases.
168 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Security Troubleshooting Tips It is advised to erase all channels before you sell or turn If you are having trouble programming HomeLink , here in your vehicle. are some of the most common solutions: •...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 169 General Information WARNING! This device complies with FCC rules Part 15 and Industry • Your motorized door or gate will open and close Canada RSS-210. Operation is subject to the following two conditions: while you are programming the universal trans- ceiver.
Page 172
170 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER SUNROOF — IF EQUIPPED WARNING! The power sunroof switch is located in the reading light. • Never leave children in a vehicle with the key in the ignition switch. Occupants, particularly unat- tended children, can become entrapped by the power sunroof while operating the power sunroof switch.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 171 Opening Sunroof — Express Closing Sunroof — Express Press the switch rearward and release it within one-half Press the switch forward and release it within one-half second and the sunroof will open automatically from any second and the sunroof will close automatically from any position.
172 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Pinch Protect Feature NOTE: The sunshade cannot be closed if the sunroof is This feature will detect an obstruction in the opening of open. the sunroof during Express Close operation. If an ob- Wind Buffeting struction in the path of the sunroof is detected, the Wind buffeting can be described as the perception of...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 173 Ignition Off Operation power outlet can power cellular phones, electronics and For vehicles not equipped with the Electronic Vehicle other low power devices. Information Center (EVIC), the power sunroof switch will remain active for 45 seconds after the ignition switch is turned to the LOCK position.
Page 176
174 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: To ensure proper operation a MOPAR knob and element must be used. CAUTION! • Do not exceed the maximum power of 160 Watts (13 Amps) at 12 Volts. If the 160 Watt (13 Amp) power rating is exceeded the fuse protecting the system will need to be replaced.
Page 177
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 175 WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Only devices designed for use in this type of power from the vehicle’s battery, even when not in use (i.e., cellular phones, etc.).
176 UNDERSTANDING THE FEATURES OF YOUR VEHICLE POWER INVERTER — IF EQUIPPED A 115 Volt (150 Watt) AC power inverter is located on the front of the center console for added convenience. This outlet can power cellular phones, electronics and other low power devices requiring power up to 150 Watts.
Page 179
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177 WARNING! CAUTION! • Many accessories that can be plugged in draw To avoid serious injury or death: • Do not use a three-prong adaptor. power from the vehicle’s battery, even when not in •...
178 UNDERSTANDING THE FEATURES OF YOUR VEHICLE CUPHOLDERS There are two cupholders located in the back for the rear Your vehicle is equipped with four cupholders. There are passengers. two illuminated cupholders located in the front. Rear Cupholders Illuminated Front Cupholders...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 179 STORAGE To open the lower glove compartment, pull outward on the release handle. Glove Compartment And Storage Bin Located on the passenger side of the instrument panel are an upper storage bin and a lower glove compartment. Glove Compartment 1 —...
180 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Door Storage The interior door panels are equipped with lower storage areas. Rear Door Storage Front Door Storage...
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 181 CONSOLE FEATURES To open the lower storage compartment, lift upward on The floor console contains both an upper and lower the lower handle to unlatch the lower storage compart- storage compartment. ment and lift the lid open. To open the upper storage compartment, push inward on the upper handle to unlatch the upper lid and lift the lid open.
182 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Press in on the flashlight to release it. WARNING! Do not operate this vehicle with a console compart- ment lid in the open position. Cellular phones, music players, and other handheld electronic devices should be stowed while driving.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 183 To install the Cargo Cover, insert either end of the cover into one of the two notches located in the rear trim panels. With one of the cover ends installed, push inward on the opposite end and install it into the same notch location of the rear trim panel.
Page 186
184 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Using the handle, pull the cover toward you and guide WARNING! the rear cover posts into the guides located on both sides of the rear trim panel. In a collision a cargo cover loose in the vehicle could cause injury.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 185 Removable Load Floor Cargo Tie-Down Loops The cargo area load floor is removable and can be There are four D-rings installed in the cargo area for washed with mild soap and water. securing cargo. Cargo Load Floor D-Rings...
Page 188
186 UNDERSTANDING THE FEATURES OF YOUR VEHICLE WARNING! WARNING! (Continued) • Place as much cargo as possible in front of the rear • Cargo tie-down loops are not safe anchors for a axle. Too much weight or improperly placed child seat tether strap. In a sudden stop or collision weight over or behind the rear axle can cause the a loop could pull loose and allow the child seat to rear of the vehicle to sway.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 187 Fold Down Speakers — If Equipped REAR WINDOW FEATURES When the liftgate is open, the speakers can swing down Rear Window Wiper/Washer off the trim panel to face rearward, for tailgating and The rear wiper/washer is controlled by a rotary switch other activities.
188 UNDERSTANDING THE FEATURES OF YOUR VEHICLE Rotate the center portion of the lever upward to the Rear Window Defroster first detent position for rear wiper operation. The rear window defroster button is located on the bottom right-side of the blower control knob. NOTE: The rear wiper operates in an intermittent mode Press this button to turn on the rear window defroster only.
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 189 NOTE: If not equipped with crossbars, your authorized CAUTION! (Continued) dealer can order and install MOPAR crossbars built • Use care when washing the inside of the rear specifically for this roof rack system. window.
Page 192
190 UNDERSTANDING THE FEATURES OF YOUR VEHICLE NOTE: CAUTION! • To help control wind noise when the crossbars are not • To prevent damage to the roof of your vehicle, DO in use, place the front crossbar in the first detent from the front of the vehicle and the rear crossbar in the NOT carry any loads on the roof rack without second detent from the rear of the vehicle.
Page 193
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 191 CAUTION! (Continued) WARNING! • Long loads which extend over the windshield, Cargo must be securely tied before driving your such as wood panels or surfboards, or loads with vehicle. Improperly secured loads can fly off the large frontal area should be secured to both the vehicle, particularly at high speeds, resulting in per- front and rear of the vehicle.
UNDERSTANDING YOUR INSTRUMENT PANEL CONTENTS Instrument Panel Features ....196 EVIC Functions ..... 217 Instrument Cluster .
Page 196
194 UNDERSTANDING YOUR INSTRUMENT PANEL Media Center 230 (REQ) — AM/FM Stereo Media Center 730N/430/430N (RHR/RER/ Radio And 6–Disc CD/DVD Changer RBZ/RHB) CD/DVD/HDD/NAV — If (MP3/WMA AUX Jack) ....224 Equipped .
Page 197
UNDERSTANDING YOUR INSTRUMENT PANEL 195 Media Center 130 With Satellite Radio Play Mode ......270 (Sales Code RES+RSC)....252 List Or Browse Mode .
198 UNDERSTANDING YOUR INSTRUMENT PANEL INSTRUMENT CLUSTER DESCRIPTIONS If jump starting is required, refer to “Jump Starting Procedures” in “What To Do In Emergencies”. 1. Fuel Gauge/Fuel Door Reminder When the ignition switch is in the ON/RUN 3. Electronic Throttle Control (ETC) Light position, the pointer will show the level of fuel This light informs you of a problem with the remaining in the fuel tank.
Page 201
UNDERSTANDING YOUR INSTRUMENT PANEL 199 on briefly as a bulb check. If the light does not come on 6. Speedometer during starting, have the system checked by an autho- Indicates vehicle speed. rized dealer. 7. Air Bag Warning Light 4. Oil Pressure Warning Light This light will turn on for four to eight seconds This light indicates low engine oil pressure.
Page 202
200 UNDERSTANDING YOUR INSTRUMENT PANEL NOTE: If either indicator flashes at a rapid rate, check If the ABS light is on, the brake system should be serviced for a defective outside light bulb. as soon as possible to restore the benefits of Anti-Lock brakes.
Page 203
UNDERSTANDING YOUR INSTRUMENT PANEL 201 12. Tachometer service. Refer to “If Your Engine Overheats” in “What To The white area of the scale shows the permissible engine Do In Emergencies” for further information. revolutions-per-minute (RPM x 1000) for each gear range. 14.
Page 204
202 UNDERSTANDING YOUR INSTRUMENT PANEL booster, the ABS pump will run when applying the brake WARNING! and a brake pedal pulsation may be felt during each stop. Driving a vehicle with the red brake light on is The dual brake system provides a reserve braking capac- dangerous.
Page 205
UNDERSTANDING YOUR INSTRUMENT PANEL 203 The light also will turn on when the parking brake is WARNING! applied with the ignition switch in the ON/RUN posi- tion. If the Transmission Temperature Warning Light is illuminated and you continue operating the vehicle, NOTE: This light shows only that the parking brake is in some circumstances you could cause the fluid to applied.
Page 206
204 UNDERSTANDING YOUR INSTRUMENT PANEL The gauge pointer will likely indicate a higher tempera- WARNING! ture when driving in hot weather, up mountain grades, or when towing a trailer. It should not be allowed to A hot engine cooling system is dangerous. You or exceed the upper limits of the normal operating range.
Page 207
UNDERSTANDING YOUR INSTRUMENT PANEL 205 20. Shift Lever Indicator 22. Tire Pressure Monitoring Telltale Light The Shift Lever Indicator is self-contained within the Each tire, including the spare (if provided), instrument cluster. It displays the gear position of the should be checked monthly when cold and automatic transmission.
Page 208
206 UNDERSTANDING YOUR INSTRUMENT PANEL reduces fuel efficiency and tire tread life, and may affect alternate tires or wheels on the vehicle that prevent the the vehicle’s handling and stopping ability. TPMS from functioning properly. Always check the TPMS malfunction telltale after replacing one or more Please note that the TPMS is not a substitute for proper tires or wheels on your vehicle, to ensure that the tire maintenance, and it is the driver’s responsibility to...
Page 209
UNDERSTANDING YOUR INSTRUMENT PANEL 207 23. Odometer Display / Trip Odometer Display Vehicle Odometer Messages This display indicates the total distance the vehicle has When the appropriate conditions exist, the following been driven. odometer messages will display: NOTE: U.S. Federal regulations require that upon trans- door .
Page 210
208 UNDERSTANDING YOUR INSTRUMENT PANEL “gASCAP” message will display in the odometer display turn the ignition switch to the ON/RUN position. To turn area. Tighten the fuel filler cap properly and press the off the message temporarily, press and release the Trip TRIP ODOMETER button to turn off the message.
Page 211
UNDERSTANDING YOUR INSTRUMENT PANEL 209 25. Malfunction Indicator Light (MIL) CAUTION! The Malfunction Indicator Light (MIL) is part of an Onboard Diagnostic system called OBD II that Prolonged driving with the MIL on could cause monitors emissions, engine, and automatic trans- damage to the engine control system.
Page 212
210 UNDERSTANDING YOUR INSTRUMENT PANEL 26. Hill Descent Indicator — If Equipped 29. Electronic Stability Control (ESC) Activation/ The symbol illuminates (is armed) when the Malfunction Indicator Light — If Equipped 4WD Lock switch is activated and the trans- The “ESC Activation/Malfunction Indicator mission range indicator is in LOW or REVERSE Light”...
UNDERSTANDING YOUR INSTRUMENT PANEL 211 • Each time the ignition is turned to ON/RUN, the ESC 31. Electronic Vehicle Information Center (EVIC) system will be ON, even if it was turned off previously. Display — If Equipped When the appropriate conditions exist, this display •...
212 UNDERSTANDING YOUR INSTRUMENT PANEL Control Buttons RESET Button To reset the display shown, turn the ignition switch to the ON position, then press and hold the RESET button located on the steering wheel. The following displays can be reset or changed: •...
UNDERSTANDING YOUR INSTRUMENT PANEL 213 ELECTRONIC VEHICLE INFORMATION CENTER The EVIC consists of the following: (EVIC) — IF EQUIPPED • System Status The Electronic Vehicle Information Center (EVIC) fea- • Vehicle Information Warning Message Displays tures a driver-interactive display that is located in the instrument cluster.
Page 216
214 UNDERSTANDING YOUR INSTRUMENT PANEL The system allows the driver to select information by MENU Button pressing the following buttons mounted on the steering Press and release the MENU button to scroll wheel: through the main menus (Fuel Economy, Warn- ings, Timer, Units, System, Personal Settings) or to exit sub-menus.
Page 217
UNDERSTANDING YOUR INSTRUMENT PANEL 215 • Personal Settings Not Avail. — Vehicle not in PARK DOWN Button Press and release the DOWN button to scroll (automatic transmission) or vehicle is in motion downward through the sub-menus. (manual transmission). • Door Ajar (with vehicle graphic showing which door is open.
216 UNDERSTANDING YOUR INSTRUMENT PANEL • Remote Start Aborted — Fuel Low indicator system is duty-cycle based, which means the engine oil change interval may fluctuate dependent upon • Remote Start Aborted — System Fault your personal driving style. • Key In Ignition Unless reset, this message will continue to display each •...
UNDERSTANDING YOUR INSTRUMENT PANEL 217 NOTE: If the indicator message illuminates when you SELECT button a second time within three seconds of start the vehicle, the oil change indicator system did not resetting the currently displayed function. Reset ALL will reset.
218 UNDERSTANDING YOUR INSTRUMENT PANEL Distance To Empty (DTE) Tire Pressure Monitor (TPM) Shows the estimated distance that can be traveled with Refer to “Starting And Operating”, “Tire Pressure Moni- the fuel remaining in the tank. This estimated distance is toring System (TPMS)”...
UNDERSTANDING YOUR INSTRUMENT PANEL 219 Personal Settings NOTE: Uconnect™ language will not change using the (Customer-Programmable Features) EVIC. Please refer to “Language Selection” in Uconnect™ This allows the driver to set and recall features when the phone — If Equipped for details. transmission is in PARK (automatic transmission) or the Auto Lock Doors vehicle is stopped (manual transmission).
Page 222
220 UNDERSTANDING YOUR INSTRUMENT PANEL RKE Unlock Driver’s Door 1st Sound Horn with Lock When Driver’s Door 1st is selected only the driver’s door When ON is selected, a short horn sound will occur when will unlock on the first press of the Remote Keyless Entry the RKE transmitter LOCK button is pressed.
Page 223
UNDERSTANDING YOUR INSTRUMENT PANEL 221 either front vehicle door will cancel this feature. Press Display Units In and hold the SELECT button when in this display until The EVIC, odometer, and Uconnect™ gps system units “OFF”, “45 sec.”, “5 min.”, or “10 min.” appears to make can be changed between English and Metric.
Page 224
222 UNDERSTANDING YOUR INSTRUMENT PANEL metallic objects) until the “CAL” message displayed in 3. Press the DOWN button until “Calibrate Compass” the EVIC turns off. The compass will now function displays in the EVIC. normally. 4. Press and release the SELECT button to start the NOTE: A good calibration requires a level surface and calibration.
Page 225
UNDERSTANDING YOUR INSTRUMENT PANEL 223 NOTE: Magnetic materials should be kept away from 1. Turn the ignition switch ON. the top of the right rear quarter window. This is where 2. Press and hold the COMPASS button for approxi- the compass sensor is located. mately two seconds.
224 UNDERSTANDING YOUR INSTRUMENT PANEL MEDIA CENTER 230 (REQ) — AM/FM STEREO Operating Instructions - Radio Mode RADIO AND 6–DISC CD/DVD CHANGER NOTE: The ignition switch must be in the ON or ACC (MP3/WMA AUX JACK) position to operate the radio. NOTE: The radio sales code is located on the lower right Power Switch/Volume Control (Rotary) side of the radio faceplate.
Page 227
UNDERSTANDING YOUR INSTRUMENT PANEL 225 SEEK Buttons If your vehicle is not equipped with or this feature is not Press and release the SEEK buttons to search for the next available on your vehicle, a “Not Equipped With listenable station in AM/FM mode. Press the right switch Uconnect Phone”...
Page 228
226 UNDERSTANDING YOUR INSTRUMENT PANEL Clock Setting Procedure INFO Button Press the INFO button for an RDS station (one with call 1. Press and hold the TIME button until the hours blink. letters displayed). The radio will return a Radio Text 2.
Page 229
UNDERSTANDING YOUR INSTRUMENT PANEL 227 Push the rotary TUNE/SCROLL control knob a second MUSIC TYPE Button time and MID will display. Turn the TUNE/SCROLL Pressing this button once will turn on the Music Type control knob to the right or left to increase or decrease the mode for five seconds.
Page 230
228 UNDERSTANDING YOUR INSTRUMENT PANEL Program Type 16-Digit Character Display Program Type 16-Digit Character Display Information Inform Top 40 Top 40 Jazz Jazz Weather Weather News News By pressing the SEEK button when the Music Type icon Nostalgia Nostalga is displayed, the radio will be tuned to the next frequency Oldies Oldies station with the same selected Music Type name.
Page 231
UNDERSTANDING YOUR INSTRUMENT PANEL 229 • DVD Enter - When the disc is in DVD Menu mode, • Angle – Repeatedly pressing SELECT will change selecting DVD Enter will allow you to play the current the viewing angle if supported by the DVD disc (if highlighted selection.
Page 232
230 UNDERSTANDING YOUR INSTRUMENT PANEL • Set Home Clock - Pressing the SELECT button allows Audio Language — If Equipped you to set the clock. Turn the TUNE/SCROLL control Selecting this item allows you to choose a default audio knob to adjust the hours and then press and turn the language (effective only if the language is supported by TUNE/SCROLL control knob to adjust the minutes.
Page 233
UNDERSTANDING YOUR INSTRUMENT PANEL 231 Audio DRC — If Equipped NOTE: The user will have to set these defaults before Selecting this item allows you to limit maximum audio loading a disc. If changes are made to these settings after dynamic range.
232 UNDERSTANDING YOUR INSTRUMENT PANEL You may add a second station to each pushbutton by Operation Instructions - (DISC MODE for CD and repeating the above procedure with this exception: Press MP3/WMA Audio Play, DVD-VIDEO) the SET button twice and SET 2 will show in the display The radio DVD player and many DVD discs are coded by window.
Page 235
UNDERSTANDING YOUR INSTRUMENT PANEL 233 NOTE: The ignition switch must be in the ON or ACC Eject Button — Ejecting Compact Disc(s) position to operate the radio. Press the EJECT button and the pushbutton with the corresponding number (1-6) where the LOAD Button —...
234 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (CD MODE) Notes On Playing MP3/WMA Files Press the SCAN button to scan through each track on the The radio can play MP3/WMA files; however, acceptable CD currently playing. MP3/WMA file recording media and formats are limited. When writing MP3/WMA files, pay attention to the TIME Button (CD MODE) following restrictions.
Page 237
UNDERSTANDING YOUR INSTRUMENT PANEL 235 The radio uses the following limits for file systems: If a disc contains multi-formats, such as CD audio and MP3/WMA tracks, the radio will only play the MP3/ • Maximum number of directory levels: 8 WMA tracks on that disc.
Page 238
236 UNDERSTANDING YOUR INSTRUMENT PANEL Playback of MP3/WMA Files MPEG Sampling Fre- Bit Rate (kbps) When a medium containing MP3/WMA data is loaded, Specification quency (kHz) the radio checks all files on the medium. If the medium 320, 256, 224, contains a lot of folders or files, the radio will take more MPEG-1 Audio 192, 160, 128,...
UNDERSTANDING YOUR INSTRUMENT PANEL 237 LIST Button (DISC Mode for MP3/WMA Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
238 UNDERSTANDING YOUR INSTRUMENT PANEL SCAN Button (Auxiliary Mode) Operating Instructions — Voice Command System No function. (If Equipped) For the radio, Refer to “Voice Command” in the EJECT Button (Auxiliary Mode) Uconnect™ User Manual located on the DVD for further No function.
UNDERSTANDING YOUR INSTRUMENT PANEL 239 Macrovision NOTE: Sirius service is not available in Hawaii and has This product incorporates copyright protection technol- limited coverage in Alaska. ogy that is protected by U.S. patents and other intellec- System Activation tual property rights. Use of this copyright protection Sirius Satellite Radio service is pre-activated, and you technology must be authorized by Macrovision, and is may begin listening immediately to the one year of audio...
Page 242
240 UNDERSTANDING YOUR INSTRUMENT PANEL 2. Your Vehicle Identification Number. placed within the line of sight of the antenna will cause decreased performance. Larger luggage items such as To access the ESN/SID, refer to the following steps: bikes should be placed as far rearward as possible, within ESN/SID Access the loading design of the rack.
Page 243
UNDERSTANDING YOUR INSTRUMENT PANEL 241 Operating Instructions - Uconnect™ Multimedia INFO Button (Satellite) Mode Pressing the INFO button will cycle the display informa- tion between Artist, Song Title, and Composer (if avail- NOTE: The ignition switch must be in the ON/RUN or able).
Page 244
242 UNDERSTANDING YOUR INSTRUMENT PANEL or turning the TUNE/SCROLL control knob within five SET Button – To Set the Pushbutton Memory seconds will allow the program format type to be selected. When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button.
UNDERSTANDING YOUR INSTRUMENT PANEL 243 Buttons 1 - 6 MEDIA CENTER 130 (SALES CODE RES) These buttons tune the radio to the channels that you NOTE: The radio sales code is located on the lower right commit to pushbutton memory (12 Satellite stations). side of the radio faceplate.
244 UNDERSTANDING YOUR INSTRUMENT PANEL Operating Instructions — Radio Mode SEEK Buttons Press and release the SEEK buttons to search for the next NOTE: The ignition switch must be in the ON or ACC listenable station in AM/FM mode. Press the right switch position to operate the radio.
Page 247
UNDERSTANDING YOUR INSTRUMENT PANEL 245 4. Adjust the minutes using the right side TUNE/ Push the rotary TUNE/SCROLL control knob a second SCROLL control knob. Press the TUNE/SCROLL control time and MID will display. Turn the TUNE/SCROLL knob to save time change. control knob to the right or left to increase or decrease the mid-range tones.
Page 248
246 UNDERSTANDING YOUR INSTRUMENT PANEL Push the rotary TUNE/SCROLL control knob again to You may add a second station to each pushbutton by exit setting tone, balance, and fade. repeating the above procedure with this exception: Press the SET/RND button twice and SET 2 will show in the AM/FM Button display window.
UNDERSTANDING YOUR INSTRUMENT PANEL 247 Operation Instructions — CD MODE For CD And If you insert a disc with the ignition ON and the radio MP3 Audio Play ON, the unit will switch from radio to CD mode and begin to play when you insert the disc. The display will NOTE: show the track number, and index time in minutes and •...
Page 250
248 UNDERSTANDING YOUR INSTRUMENT PANEL EJECT Button - Ejecting a CD the current selection. Pressing and holding the SEEK Press the EJECT button to eject the CD. button will allow faster scrolling through the tracks in CD and MP3 modes. TIME Button Press this button to change the display from a large CD If you have ejected a disc and have not removed it within...
UNDERSTANDING YOUR INSTRUMENT PANEL 249 SET/RND Button (Random Play Button) Supported Medium Formats (File Systems) Press this button while the CD is playing to activate The medium formats supported by the radio are ISO 9660 Random Play. This feature plays the selections on the Level 1 and Level 2 and includes the Joliet extension.
Page 252
250 UNDERSTANDING YOUR INSTRUMENT PANEL • Maximum number of characters in file/folder names: When using the MP3 encoder to compress audio data to an MP3 file, the bit rate and sampling frequencies in the • Level 1: 12 (including a separator . and a three- following table are supported.
UNDERSTANDING YOUR INSTRUMENT PANEL 251 Playlist files are not supported. MP3 Pro files are not To increase the speed of disc loading, it is recommended supported. to use CD-R media and single-session discs. To create a single-session disc, enable the “Disc at Once” option Playback of MP3 Files before writing to the disc.
252 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) Press this button to change the display to time of day. The time of day will display for five seconds (when ignition is OFF). MEDIA CENTER 130 WITH SATELLITE RADIO (SALES CODE RES+RSC) NOTE: The radio sales code is located on the lower right side of the radio faceplate.
Page 255
UNDERSTANDING YOUR INSTRUMENT PANEL 253 Power Switch/Volume Control (Rotary) Voice Command System (Radio) — If Equipped Push the ON/VOLUME control knob to turn on the Refer to “Voice Command” in “Understanding The Fea- radio. Push the ON/VOLUME control knob a second tures Of Your Vehicle”.
Page 256
254 UNDERSTANDING YOUR INSTRUMENT PANEL If your vehicle is not equipped with or this feature is not 5. To exit, press any button/knob or wait five seconds. available on your vehicle, a “Not Equipped With Uconnect The clock can also be set by pressing the SETUP button. Phone”...
Page 257
UNDERSTANDING YOUR INSTRUMENT PANEL 255 TUNE Control Push the rotary TUNE/SCROLL control knob a fourth Turn the rotary TUNE/SCROLL control knob clockwise time and BALANCE will display. Turn the TUNE/ to increase or counterclockwise to decrease the frequency. SCROLL control knob to the right or left to adjust the sound level from the right or left side speakers.
Page 258
256 UNDERSTANDING YOUR INSTRUMENT PANEL Toggle the MUSIC TYPE button to select the following Program Type 16-Digit Character Display format types: Public Public Program Type 16-Digit Character Display Rhythm and Blues R & B No program type or Religious Music Rel Musc None undefined...
Page 259
UNDERSTANDING YOUR INSTRUMENT PANEL 257 If a preset button is activated while in the Music Type SET/RND Button — To Set the Pushbutton (Program Type) mode, the Music Type mode will be Memory exited and the radio will tune to the preset station. When you are receiving a station that you wish to commit to pushbutton memory, press the SET/RND SETUP Button...
258 UNDERSTANDING YOUR INSTRUMENT PANEL • This radio is capable of playing compact discs (CD), Every time a preset button is used, a corresponding button number will display. recordable compact discs (CD-R), rewritable compact discs (CD-RW), compact discs with MP3 tracks and Buttons 1 - 6 multisession compact discs with CD and MP3 tracks.
Page 261
UNDERSTANDING YOUR INSTRUMENT PANEL 259 A disc can be ejected with the radio and ignition OFF. CAUTION! NOTE: Ejecting with the ignition OFF is not allowed on • This CD player will accept 4–3/4 in (12 cm) discs convertible or soft-top models (if equipped). only.
260 UNDERSTANDING YOUR INSTRUMENT PANEL RW/FF Notes On Playing MP3 Files Press and hold FF (Fast Forward) and the CD player will The radio can play MP3 files; however, acceptable MP3 begin to fast forward until FF is released or RW or file recording media and formats are limited.
Page 263
UNDERSTANDING YOUR INSTRUMENT PANEL 261 The radio uses the following limits for file systems: Multisession disc formats are supported by the radio. Multisession discs may contain combinations of normal • Maximum number of folder levels: 8 CD audio tracks and computer files (including MP3 files). •...
Page 264
262 UNDERSTANDING YOUR INSTRUMENT PANEL rates (VBR) are also supported. The majority of MP3 files Playback of MP3 Files use a 44.1 kHz sampling rate and a 192, 160, 128, 96 or When a medium containing MP3 data is loaded, the VBR bit rates.
UNDERSTANDING YOUR INSTRUMENT PANEL 263 LIST Button (CD Mode for MP3 Play) Press and hold the INFO button again for three seconds Pressing the LIST button will bring up a list of all folders to return to elapsed time display. on the disc.
264 UNDERSTANDING YOUR INSTRUMENT PANEL TIME Button (Auxiliary Mode) radio system in your vehicle. Sirius will supply a wel- Press this button to change the display to time of day. The come kit that contains general information, including time of day will display for five seconds (when the how to setup your on-line listening account.
Page 267
UNDERSTANDING YOUR INSTRUMENT PANEL 265 using the TUNE/SCROLL control knob until Sirius ID is Reception Quality selected. Press the TUNE/SCROLL control knob and the Satellite reception may be interrupted due to one of the Sirius ID number will display. The Sirius ID number following reasons: display will time out in two minutes.
Page 268
266 UNDERSTANDING YOUR INSTRUMENT PANEL SEEK Buttons additional three seconds will make the radio display the Press and release the SEEK buttons to search for the next Song Title all of the time (press and hold again to return channel in Satellite mode. Press the right switch to seek to normal display).
Page 269
UNDERSTANDING YOUR INSTRUMENT PANEL 267 Toggle the MUSIC TYPE button again to select the music SET Button – To Set the Pushbutton Memory type. When you are receiving a channel that you wish to commit to pushbutton memory, press the SET button. By pressing the SEEK button when the Music Type The symbol SET 1 will now show in the display window.
268 UNDERSTANDING YOUR INSTRUMENT PANEL Every time a preset button is used, a corresponding This feature allows an iPod or external USB device to be button number will display. plugged into the USB port, located in the center console or glove compartment. Buttons 1 - 6 These buttons tune the radio to the channels that you iPod control supports Mini, 4G, Photo, Nano, 5G iPod...
UNDERSTANDING YOUR INSTRUMENT PANEL 269 Connecting The iPod Or External USB Device Once the audio device is connected and synchronized to Use the connection cable to connect an iPod or external the vehicle’s iPod /USB/MP3 control system (iPod or USB device to the vehicle’s USB/AUX connector port external USB device may take a few minutes to connect), which is located in the center console or glove compart- the audio device starts charging and is ready for use by...
270 UNDERSTANDING YOUR INSTRUMENT PANEL • The audio device can be controlled using the radio mode. In Play mode, the following buttons on the radio buttons to Play, Browse, and List the iPod contents. faceplate may be used to control the iPod or external USB device and display data: •...
Page 273
UNDERSTANDING YOUR INSTRUMENT PANEL 271 • A single press backward << RW or forward FF >> will • Press the SCAN button to use iPod /USB/MP3 de- jump backward or forward respectively, for five vice scan mode, which will play the first 10 seconds of seconds.
272 UNDERSTANDING YOUR INSTRUMENT PANEL • During all List modes, the iPod displays all lists in List Or Browse Mode During Play mode, pressing any of the buttons described “wrap-around” mode. So if the track is at the below, will bring up List mode. List mode enables bottom of the list, just turn the wheel backward scrolling through the list of menus and tracks on the (counterclockwise) to get to the track faster.
Page 275
UNDERSTANDING YOUR INSTRUMENT PANEL 273 • Pressing a PRESET button will display the current CAUTION! list on the top line and the first item in that list on • Leaving the iPod or external USB device (or any the second line. supported device) anywhere in the vehicle in •...
274 UNDERSTANDING YOUR INSTRUMENT PANEL Bluetooth Streaming Audio (BTSA) 2. After the Ready prompt and the following beep, say Music can be streamed from your cellular phone to the Setup , then Select Audio Devices . Uconnect™ phone system. 3. Say the name of the audio device or ask the Controlling BTSA Using Radio Buttons Uconnect™...
UNDERSTANDING YOUR INSTRUMENT PANEL 275 STEERING WHEEL AUDIO CONTROLS The right-hand control is a rocker-type switch with a The remote sound system controls are located on the rear pushbutton in the center and controls the volume and surface of the steering wheel. Reach behind the wheel to mode of the sound system.
276 UNDERSTANDING YOUR INSTRUMENT PANEL The button located in the center of the left-hand control CD/DVD DISC MAINTENANCE will tune to the next preset station that you have pro- To keep a CD/DVD in good condition, take the following grammed in the radio preset pushbutton. precautions: CD Player 1.
UNDERSTANDING YOUR INSTRUMENT PANEL 277 NOTE: If you experience difficulty in playing a particu- CLIMATE CONTROLS lar disc, it may be damaged (i.e., scratched, reflective The air conditioning and heating system is designed to coating removed, a hair, moisture or dew on the disc) make you comfortable in all types of weather.
Page 280
278 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Temperature Control Rotate this control to regulate the Rotate this control to regulate the tem- amount of air forced through the ven- perature of the air inside the passenger tilation system in any mode. The compartment.
Page 281
UNDERSTANDING YOUR INSTRUMENT PANEL 279 Mode Control (Air Direction) NOTE: For all settings, except full cold or full hot, there Rotate this control to choose from sev- is a difference in temperature between the upper and eral patterns of air distribution. You lower outlets.
Page 282
280 UNDERSTANDING YOUR INSTRUMENT PANEL Defrost Recirculation Control Air is directed through the windshield and side Pressing the Recirculation Control button will window demist outlets. Use this mode with maxi- put the system in recirculation mode. This can mum blower and temperature settings for best wind- be used when outside conditions such as shield and side window defrosting.
Page 283
UNDERSTANDING YOUR INSTRUMENT PANEL 281 • The A/C can be deselected manually without disturb- NOTE: The air conditioning compressor will not engage ing the mode control selection. until the engine has been running for about 10 seconds. • When the ignition switch is turned to the LOCK •...
282 UNDERSTANDING YOUR INSTRUMENT PANEL Automatic Temperature Control (ATC) — If Automatic Operation Equipped Operation of the system is quite simple. The Automatic Temperature Control system automati- 1. Turn the Mode Control knob (on the right) and the cally maintains the climate in the cabin of the vehicle at Blower Control knob (on the left) to AUTO.
Page 285
UNDERSTANDING YOUR INSTRUMENT PANEL 283 • Pressing the Air Conditioning Control button while in You will experience the greatest efficiency by simply allowing the system to function automatically. Selecting AUTO mode will cause the LED in the control button the “O” (OFF) position on the blower control stops the to flash three times and then turn off.
Page 286
284 UNDERSTANDING YOUR INSTRUMENT PANEL Blower Control Manual Operation For full automatic operation or for This system offers a full complement of manual override automatic blower operation, turn the features, which consist of Blower Preferred Automatic, knob to the AUTO position. In manual Mode Preferred Automatic, or Blower and Mode Pre- mode there are seven blower speeds ferred Automatic.
Page 287
UNDERSTANDING YOUR INSTRUMENT PANEL 285...
Page 288
286 UNDERSTANDING YOUR INSTRUMENT PANEL • Floor The operator can override the AUTO mode setting to change airflow distribution by rotating the Mode Control Air is directed through the floor outlets with a knob (on the right) to one of the following positions. small amount flowing through the defrost and side window demist outlets.
Page 289
UNDERSTANDING YOUR INSTRUMENT PANEL 287 • Air Conditioner Control NOTE: • When the ignition switch is turned to the LOCK Press this button to turn on the air conditioning during manual operation position, the recirculation feature will be cancelled. only. When the air conditioning is •...
288 UNDERSTANDING YOUR INSTRUMENT PANEL • Most of the time, when in Automatic Operation, you Summer Operation can temporarily put the system into Recirculation The engine cooling system in air-conditioned vehicles Mode by pressing the Recirculation button. However, must be protected with a high-quality antifreeze coolant under certain conditions, while in Automatic Mode, to provide proper corrosion protection and to protect the system is blowing air out the defrost vents.
Page 291
UNDERSTANDING YOUR INSTRUMENT PANEL 289 Window Fogging Outside Air Intake Interior fogging on the windshield can be quickly re- Make sure the air intake, located directly in front of the moved by turning the mode selector to Defrost. The windshield, is free of obstructions such as leaves. Leaves Defrost/Floor mode can be used to maintain a clear collected in the air intake may reduce airflow, and if they windshield and provide sufficient heating.
Page 292
290 UNDERSTANDING YOUR INSTRUMENT PANEL Control Setting Suggestions for Various Weather Conditions...
STARTING AND OPERATING 295 STARTING PROCEDURES WARNING! (Continued) Before starting your vehicle, adjust your seat, adjust both • Do not leave the key fob in or near the vehicle. A inside and outside mirrors, and fasten your seat belts. child could operate power windows, other con- trols, or move the vehicle.
296 STARTING AND OPERATING Automatic Transmission – If Equipped Simply turn the ignition switch to the START position The shift lever must be in the PARK or NEUTRAL and release when the engine starts. If the engine fails to position before you can start the engine. Apply the brakes start within 15 seconds, turn the ignition switch to the before shifting to any driving gear.
STARTING AND OPERATING 297 Extreme Cold Weather (Below –20°F or 29°C) WARNING! To ensure reliable starting at these temperatures, use of an externally powered electric engine block heater (avail- Never pour fuel or other flammable liquid into the able from your authorized dealer) is recommended. throttle body air inlet opening in an attempt to start the vehicle.
298 STARTING AND OPERATING ENGINE BLOCK HEATER — IF EQUIPPED MANUAL TRANSMISSION — IF EQUIPPED The engine block heater warms the engine, and permits Five–Speed Manual Transmission quicker starts in cold weather. Connect the cord to a standard 110-115 Volt AC electrical outlet with a WARNING! grounded, three-wire extension cord.
STARTING AND OPERATING 299 For most city driving, you will find it easier to use only the lower gears. For steady highway driving with light accelerations, fifth gear is recommended. Never drive with your foot resting on the clutch pedal, and never try to hold the vehicle on a hill with the clutch pedal partially engaged.
300 STARTING AND OPERATING To maintain a safe speed and prolong brake life, shift Manual Transmission Recommended Shift Speeds down to second or first gear when descending a steep Units in mph (km/h) grade. Accel- Engine 1 to 2 2 to 3 3 to 4 4 to 5 eration...
Page 303
STARTING AND OPERATING 301 CAUTION! (Continued) WARNING! (Continued) • Do not shift between PARK, REVERSE, NEU- • Before exiting a vehicle, always apply the parking TRAL, or DRIVE when the engine is above idle brake, shift the transmission into PARK, and re- speed.
302 STARTING AND OPERATING Key Ignition Park Interlock Interlock System” in this section). To drive, move the shift This vehicle is equipped with a Key Ignition Park Inter- lever from PARK or NEUTRAL to the DRIVE position. lock which requires the shift lever to be placed in PARK NOTE: The Continuously Variable Automatic Transmis- before the ignition switch can be turned to the LOCK/ sion (CVT) changes ratios in a continuous manner.
STARTING AND OPERATING 303 transmission gear ratios, and will display the current PARK gear in the instrument cluster as 6, 5, 4, 3, 2, 1. This range supplements the parking brake by locking the transmission. The engine can be started in this range. Gear Ranges Never attempt to use PARK while the vehicle is in DO NOT race the engine when shifting from PARK or...
Page 306
304 STARTING AND OPERATING WARNING! WARNING! (Continued) • It is dangerous to move the shift lever out of PARK • Never use the PARK position as a substitute for or NEUTRAL if the engine speed is higher than the parking brake. Always apply the parking idle speed.
Page 307
STARTING AND OPERATING 305 WARNING! (Continued) WARNING! (Continued) • Unintended movement of a vehicle could injure • Allowing children to be in a vehicle unattended is those in or near the vehicle. As with all vehicles, dangerous for a number of reasons. A child or you should never exit a vehicle while the engine is others could be seriously or fatally injured.
Page 308
306 STARTING AND OPERATING REVERSE CAUTION! (Continued) This range is for moving the vehicle backward. Shift into • DO NOT race the engine when shifting from REVERSE only after the vehicle has come to a complete PARK or NEUTRAL into another gear range, as stop.
Page 309
STARTING AND OPERATING 307 using a lower gear will improve performance and extend CAUTION! transmission life by reducing excessive shifting and heat buildup. Towing the vehicle, coasting, or driving for any other reason with the transmission in NEUTRAL can result During sustained high speed driving or trailer towing up in severe transmission damage.
308 STARTING AND OPERATING AUTOSTICK AutoStick operation is activated in the DRIVE position AutoStick is a driver-interactive transmission that offers by moving the shift lever side-to-side. Moving the shift six manual ratio changes to provide you with more lever to the (+) side will activate AutoStick and shift up control.
STARTING AND OPERATING 309 • When heavy Anti-Lock Brake System (ABS) applica- FOUR-WHEEL DRIVE OPERATION — IF tion is detected EQUIPPED This feature provides full time, on-demand, four–wheel General Information drive (4WD). • If a ratio other than first is selected and the vehicle is brought to a stop, the transmission control logic will automatically select the first gear ratio.
310 STARTING AND OPERATING traction surfaces, activate the “4WD LOCK” switch by They are not designed for cornering at the same speeds as pulling up once and releasing. This locks the center conventional two-wheel drive vehicles any more than coupling allowing more torque to be sent to the rear low-slung sports cars are designed to perform satisfacto- wheels.
STARTING AND OPERATING 311 you will need to use your own good judgment on what is When To Use Low (L Off-Road) With The 4WD safe and what is not. When on a trail, you should always Lock Lever Engaged be looking ahead for surface obstacles and changes in When driving off-road, shift into low (L Off-Road) and terrain.
312 STARTING AND OPERATING Driving In Snow, Mud And Sand CAUTION! There is a drastic reduction in traction when driving in snow, mud or sand. The vehicle will be less responsive to On icy or slippery roads, do not downshift at high steering, acceleration and braking inputs.
STARTING AND OPERATING 313 Sand CAUTION! Soft sand is very difficult to travel through with full tire pressure. When crossing soft sandy spots in a trail Reduced tire pressures may cause tire unseating and maintain your vehicle’s momentum and do not stop. The total loss of air pressure.
Page 316
314 STARTING AND OPERATING is on the hill side trail. Is the trail straight up and down? you approach the crest of a hill, ease off the accelerator What is on top and the other side? Are there ruts, rocks, and maintain headway by turning the steering wheel no branches or other obstacles on the path? Can you safely more than a 1/4 turn quickly back and forth.
Page 317
STARTING AND OPERATING 315 controlled descent? Are there obstacles? Is it a straight which increases the possibilities of a down-hill slide or descent? Is there plenty of distance at the base of the hill rollover. Make sure the surface has good traction with to regain control if the vehicle descends to fast? If you feel firm and stable soils.
316 STARTING AND OPERATING your vehicles abilities and be able to recover it if some- WARNING! thing goes wrong. You should never stop or shut a vehicle off when crossing deep water unless you ingested If the engine stalls or you lose headway or cannot water into the engine air intake.
Page 319
STARTING AND OPERATING 317 the vehicle will sink in, effectively increasing the water CAUTION! level on the vehicle. Be sure to consider this when determining the depth and the ability to safely cross. Water ingestion into the transaxle, transfer case, engine or vehicle interior can occur if you drive too Crossing Puddles, Pools, Flooded Areas Or Other fast or through too deep of water.
318 STARTING AND OPERATING • Check for accumulations of plants or brush. These After Driving Off-Road Off-road operation puts more stress on your vehicle than things could be a fire hazard. They might hide damage does most on-road driving. After going off-road, it is to fuel lines, brake hoses, axle pinion seals, and always a good idea to check for damage.
STARTING AND OPERATING 319 • If you experience unusual vibration after driving in NOTE: • Increased noise levels at the end of the steering wheel mud, slush or similar conditions, check the wheels for impacted material. Impacted material can cause a travel are considered normal and do not indicate that wheel imbalance and freeing the wheels of it will there is a problem with the power steering system.
320 STARTING AND OPERATING CAUTION! CAUTION! Prolonged operation of the steering system at the end Do not use chemical flushes in your power steering of the steering wheel travel will increase the steering system as the chemicals can damage your power fluid temperature and it should be avoided when steering components.
STARTING AND OPERATING 321 If necessary, add fluid to restore to the proper indicated level. With a clean cloth, wipe any spilled fluid from all surfaces. Refer to “Fluids, Lubricants, and Genuine Parts” in “Maintaining Your Vehicle” for further information. PARKING BRAKE Before leaving the vehicle, make sure that the parking brake is fully applied.
Page 324
322 STARTING AND OPERATING NOTE: WARNING! • When the parking brake is applied and the automatic • When leaving the vehicle, always remove the key transmission is placed in gear, the “Brake Warning Light” will flash. If vehicle speed is detected, a chime fob from the ignition and lock your vehicle.
STARTING AND OPERATING 323 any reason (for example, repeated brake applications WARNING! (Continued) with the engine off), the brakes will still function. How- • Always fully apply the parking brake when leav- ever, the effort required to brake the vehicle will be much ing your vehicle or it may roll and cause damage or greater than that required with the power system oper- injury.
324 STARTING AND OPERATING malfunction is caused by an internal leak, as the brake WARNING! fluid in the master cylinder drops, the “Brake Warning • Pumping of the anti-lock brakes will diminish Light” will light. their effectiveness and may lead to a collision. WARNING! Pumping makes the stopping distance longer.
Page 327
STARTING AND OPERATING 325 If the “ABS Warning Light” is on, the brake system WARNING! (Continued) should be serviced as soon as possible to restore the • The capabilities of an ABS-equipped vehicle must benefits of anti-lock brakes. If the “ABS Warning Light” never be exploited in a reckless or dangerous does not come on when the ignition switch is turned to manner which could jeopardize the user’s safety...
326 STARTING AND OPERATING ABS is activated during braking under certain road or WARNING! stopping conditions. ABS-inducing conditions can in- clude ice, snow, gravel, bumps, railroad tracks, loose The Anti-Lock Brake System (ABS) contains sophis- debris, or panic stops. ticated electronic equipment that may be susceptible to interference caused by improperly installed or You may also experience the following when the brake high output radio transmitting equipment.
STARTING AND OPERATING 327 Assist (HSA), and Electronic Stability Control (ESC). All Anti-Lock Brake System (ABS). Applying the brakes very systems work together to enhance vehicle stability and quickly results in the best BAS assistance. To receive the control in various driving conditions and are commonly benefit of the system, you must apply continuous brak- referred to as ESC.
328 STARTING AND OPERATING either the “Partial Off” or “Full Off” modes. Refer to WARNING! (Continued) “Electronic Stability Control (ESC)” in this section of this • The capabilities of a BAS-equipped vehicle must manual. never be exploited in a reckless or dangerous Electronic Roll Mitigation (ERM) manner which could jeopardize the user’s safety This system anticipates the potential for wheel lift by...
STARTING AND OPERATING 329 NOTE: Anytime the ESC system is in the “Full Off” Hill Descent Control (HDC) – If Equipped mode, ERM is disabled. Refer to “Electronic Stability This system maintains vehicle speed while descending Control (ESC)” in this section for a complete explanation hills during off-road driving situations.
330 STARTING AND OPERATING Off” button for five seconds. Refer to “Electronic Stability WARNING! Control (ESC)” in this section of the manual. HDC is only intended to assist the driver in control- HDC operation can be overridden with brake application ling vehicle speed when descending hills.
Page 333
STARTING AND OPERATING 331 HSA Activation Criteria Disabling/Enabling HSA The following criteria must be met in order for HSA to If you wish to turn on or off the HSA system, it can be activate: done using the Customer Programmable Features in the Electronic Vehicle Information Center (EVIC).
332 STARTING AND OPERATING 5. Release the clutch pedal. Electronic Stability Control (ESC) 6. Rotate the steering wheel one-half turn to the left. This system enhances directional control and stability of the vehicle under various driving conditions. ESC cor- 7. Press the “ESC Off” switch (located in the lower rects for over-steering or under-steering of the vehicle by switch bank below the climate controls) four times within applying the brake of the appropriate wheel to assist in...
Page 335
STARTING AND OPERATING 333 ESC Operating Modes WARNING! The ESC system has three available operating modes for • Electronic Stability Control (ESC) cannot prevent four-wheel drive equipped vehicles and two available operating modes for two-wheel drive equipped vehicles. the natural laws of physics from acting on the vehicle, nor can it increase the traction afforded by Full On (Four-Wheel Drive Models) Or On prevailing road conditions.
Page 336
334 STARTING AND OPERATING in deep snow, sand or gravel conditions and more wheel WARNING! spin than ESC would normally allow is required to gain traction. When in “Partial Off” mode, the TCS functionality of ESC, (except for the limited slip feature described in To turn ESC on again, momentarily press the “ESC Off”...
STARTING AND OPERATING 335 “ESC Off” message will appear in the odometer. Press into the PARK position from any other position, and then and release the Trip Odometer button located on the moved out of the PARK position. This will occur even if instrument cluster to clear this message.
Page 338
336 STARTING AND OPERATING Light” comes on continuously with the engine running, a NOTE: • The “ESC Activation/Malfunction Indicator Light” malfunction has been detected in the ESC system. If this light remains on after several ignition cycles, and the and the “ESC OFF Indicator Light” come on momen- vehicle has been driven several miles (kilometers) at tarily each time the ignition switch is turned ON.
STARTING AND OPERATING 337 TIRE SAFETY INFORMATION NOTE: • P (Passenger) - Metric tire sizing is based on U.S. Tire Markings design standards. P-Metric tires have the letter “P” molded into the sidewall preceding the size designa- tion. Example: P215/65R15 95H. •...
Page 340
338 STARTING AND OPERATING • High flotation tire sizing is based on U.S. design compact spare tires have the letter “T” or “S” molded into the sidewall preceding the size designation. Ex- standards and it begins with the tire diameter molded ample: T145/80D18 103M.
Page 341
STARTING AND OPERATING 339 EXAMPLE: Service Description: 95 = Load Index — A numerical code associated with the maximum load a tire can carry H = Speed Symbol — A symbol indicating the range of speeds at which a tire can carry a load corresponding to its load index under certain operating conditions —...
340 STARTING AND OPERATING Tire Identification Number (TIN) Look for the TIN on the outboard side of black sidewall The TIN may be found on one or both sides of the tire, tires as mounted on the vehicle. If the TIN is not found on however, the date code may only be on one side.
STARTING AND OPERATING 341 Tire Terminology And Definitions Term Definition B-Pillar The vehicle B-Pillar is the structural member of the body located behind the front door. Cold Tire Inflation Pressure Cold tire inflation pressure is defined as the tire pressure after the vehicle has not been driven for at least 3 hours, or driven less than 1 mile (1.6 km) after sitting for a three hour period.
342 STARTING AND OPERATING Tire Loading And Tire Pressure Tire And Loading Information Placard Tire And Loading Information Placard Location NOTE: The proper cold tire inflation pressure is listed on the driver’s side B-Pillar or the rear edge of the driver’s side door.
Page 345
STARTING AND OPERATING 343 axles must not be exceeded. For further information on This placard tells you important information about GAWRs, vehicle loading, and trailer towing, refer to the: “Vehicle Loading” in this section. 1) number of people that can be carried in the vehicle 2) total weight your vehicle can carry To determine the maximum loading conditions of your vehicle, locate the statement “The combined weight of...
Page 346
344 STARTING AND OPERATING 3. Subtract the combined weight of the driver and pas- NOTE: • The following table shows examples on how to calcu- sengers from XXX lbs or XXX kg. late total load, cargo/luggage, and towing capacities 4. The resulting figure equals the available amount of of your vehicle with varying seating configurations cargo and luggage load capacity.
346 STARTING AND OPERATING Safety WARNING! WARNING! Overloading of your tires is dangerous. Overloading can cause tire failure, affect vehicle handling, and • Improperly inflated tires are dangerous and can increase your stopping distance. Use tires of the cause collisions. recommended load capacity for your vehicle.
STARTING AND OPERATING 347 Tire Inflation Pressures WARNING! (Continued) The proper cold tire inflation pressure is listed on the left • Unequal tire pressures from one side of the ve- side “B” Pillar or rear edge of the driver’s side door. hicle to the other can cause the vehicle to drift to Some vehicles may have Supplemental Tire Pressure the right or left.
Page 350
348 STARTING AND OPERATING Tire pressures change by approximately 1 psi (7 kPa) per CAUTION! 12°F (7°C) of air temperature change. Keep this in mind when checking tire pressure inside a garage, especially in After inspecting or adjusting the tire pressure, al- the Winter.
STARTING AND OPERATING 349 Tire Pressures For High Speed Operation Radial Ply Tires The manufacturer advocates driving at safe speeds WARNING! within posted speed limits. Where speed limits or condi- tions are such that the vehicle can be driven at high Combining radial ply tires with other types of tires speeds, maintaining correct tire inflation pressure is very on your vehicle will cause your vehicle to handle...
350 STARTING AND OPERATING vehicle. If your vehicle has this option refer to an Compact Spare Tire – If Equipped authorized tire dealer for the recommended tire rotation The compact spare is for temporary emergency use only. pattern. You can identify if your vehicle is equipped with a compact spare by looking at the spare tire description on If your vehicle is not equipped with an original equip- the Tire and Loading Information Placard located on the...
STARTING AND OPERATING 351 your original equipment tire, replace (or repair) the WARNING! original equipment tire and reinstall on the vehicle at the first opportunity. Compact spares are for temporary emergency use only. With these spares, do not drive more than Limited-Use Spare –...
352 STARTING AND OPERATING Refer to “Freeing A Stuck Vehicle” in “What To Do In WARNING! Emergencies” for further information. Limited-use spares are for emergency use only. In- WARNING! stallation of this limited-use spare tire affects vehicle handling. With this tire, do not drive more than the Fast spinning tires can be dangerous.
STARTING AND OPERATING 353 Life Of Tire The service life of a tire is dependent upon varying factors including, but not limited to: • Driving style • Tire pressure • Distance driven WARNING! Tires and the spare tire should be replaced after six years, regardless of the remaining tread.
354 STARTING AND OPERATING Replacement Tires It is recommended you contact your original equipment The tires on your new vehicle provide a balance of many or an authorized tire dealer with any questions you may characteristics. They should be inspected regularly for have on tire specifications or capability.
STARTING AND OPERATING 355 TIRE CHAINS WARNING! (Continued) Due to limited clearance, tire chains are not recom- • Never use a tire with a smaller load index or mended. capacity other than what was originally equipped on your vehicle. Using a tire with a smaller load CAUTION! index could result in tire overloading and failure.
356 STARTING AND OPERATING Snow tires generally have lower speed ratings than what These effects can be reduced by timely rotation of tires. was originally equipped with your vehicle and should The benefits of rotation are especially worthwhile with not be operated at sustained speeds over 75 mph aggressive tread designs such as those on all season type (120 km/h).
STARTING AND OPERATING 357 when the outside temperature decreases, the tire pressure will decrease. Tire pressure should always be set based on “cold inflation tire pressure”. This is defined as the tire pressure after the vehicle has not been driven for at least three hours, or driven less than 1 mile (1.6 km) after a three hour period.
Page 360
358 STARTING AND OPERATING The TPMS will continue to warn the driver of low tire For example, your vehicle may have a recommended pressure as long as the condition exists, and will not turn cold (parked for more than three hours) placard pressure off until the tire pressure is at or above the recommended of 30 psi (207 kPa).
Page 361
STARTING AND OPERATING 359 NOTE: CAUTION! • The TPMS is not intended to replace normal tire care • The TPMS has been optimized for the original and maintenance or to provide warning of a tire failure or condition. equipment tires and wheels. TPMS pressures and warnings have been established for the tire size •...
360 STARTING AND OPERATING • Seasonal temperature changes will affect tire pressure, • Four Tire Pressure Monitoring Sensors and the TPMS will monitor the actual tire pressure in • Tire Pressure Monitoring Telltale Light the tire. Tire Pressure Monitoring Low Pressure Warnings Base System The Tire Pressure Monitoring Telltale Light will illumi- This is the TPMS warning indicator located in the...
Page 363
STARTING AND OPERATING 361 Check TPMS Warnings NOTE: Your vehicle is equipped with a compact spare The Tire Pressure Monitoring Telltale Light will flash on wheel and tire assembly. and off for 75 seconds and remain on solid when a system 1.
362 STARTING AND OPERATING 4. For each subsequent ignition key cycle, a chime will Premium System – If Equipped sound and the Tire Pressure Monitoring Telltale Light The TPMS uses wireless technology with wheel rim will flash on and off for 75 seconds and then remain on mounted electronic sensors to monitor tire pressure lev- solid.
Page 365
STARTING AND OPERATING 363 • Various Tire Pressure Monitoring System Messages, which display in the Electronic Vehicle Information Center (EVIC) • Tire Pressure Monitoring Telltale Light Tire Pressure Monitoring Low Pressure Warnings The Tire Pressure Monitoring Telltale Light will illumi- nate in the instrument cluster and an audible chime will be activated when one or more of the four active road tire pressures are low.
Page 366
364 STARTING AND OPERATING the graphic display of the pressure value(s) will stop flashing, and the Tire Pressure Monitoring Light will extinguish once the updated tire pressure(s) have been received. The vehicle may need to be driven for up to 20 minutes above 15 mph (24 km/h) to receive this information.
Page 367
STARTING AND OPERATING 365 will be displayed instead of dashes. A system fault can pressure values still shown. This indicates that the pres- occur with any of the following scenarios: sure values are still being received from the TPM sensors but they may not be located in the correct vehicle 1.
366 STARTING AND OPERATING 3. However, after driving the vehicle for up to 20 min- limit in any of the four active road tires. The vehicle may utes above 15 mph (24 km/h), the Tire Pressure Moni- need to be driven for up to 20 minutes above 15 mph toring Telltale Light will flash on and off for 75 seconds (24 km/h) in order for the TPMS to receive this and then remain on solid.
STARTING AND OPERATING 367 FUEL REQUIREMENTS Over 40 auto manufacturers worldwide have issued and endorsed consistent gasoline specifications (the World- 2.0L And 2.4L Engine wide Fuel Charter, WWFC) which define fuel properties This engine is designed to meet all emis- necessary to deliver enhanced emissions, performance, sions regulations and provide excellent and durability for your vehicle.
368 STARTING AND OPERATING Gasoline/Oxygenate Blends E-85 Usage In Non-Flex Fuel Vehicles Some fuel suppliers blend unleaded gasoline with oxy- Non-FFV vehicles are compatible with gasoline contain- genates such as Ethanol. Fuels blended with oxygenates ing 10% ethanol (E10). Gasoline with higher ethanol may be used in your vehicle.
STARTING AND OPERATING 369 • drain the fuel tank (see your authorized dealer) Materials Added To Fuel All gasoline sold in the United States is required to More extensive repairs will be required for prolonged contain effective detergent additives. Use of additional exposure to E-85 fuel.
370 STARTING AND OPERATING Carbon Monoxide Warnings CAUTION! (Continued) • An out-of-tune engine or certain fuel or ignition WARNING! malfunctions can cause the catalytic converter to Carbon monoxide (CO) in exhaust gases is deadly. overheat. If you notice a pungent burning odor or Follow the precautions below to prevent carbon some light smoke, your engine may be out of tune monoxide poisoning:...
STARTING AND OPERATING 371 After removing the gas cap, place the gas cap tether cable WARNING! (Continued) over a hook on the inside of the fuel door. This keeps the • Guard against carbon monoxide with proper gas cap suspended away from and protects the vehicle’s maintenance.
Page 374
372 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Never add fuel when the engine is running. This is • Damage to the fuel system or emission control in violation of most state and Federal fire regula- system could result from using an improper fuel tions and may cause the MIL to turn on.
STARTING AND OPERATING 373 Loose Fuel Filler Cap Message Vehicle Certification Label If the vehicle diagnostic system determines that the fuel Your vehicle has a Vehicle Certification Label attached to filler cap is loose or improperly installed, a “gASCAP” the driver’s door B-Pillar. message will be displayed in the Odometer/Trip Odom- The label contains the following information: eter in the instrument cluster.
Page 376
374 STARTING AND OPERATING Gross Vehicle Weight Rating (GVWR) Curb Weight The GVWR is the total allowable weight of your vehicle. The curb weight of a vehicle is defined as the total weight This includes driver, passengers, and cargo. The total of the vehicle with all fluids, including vehicle fuel, at full load must be limited so that you do not exceed the capacity conditions, and with no occupants or cargo...
STARTING AND OPERATING 375 Overloading can cause potential safety hazards and TRAILER TOWING shorten useful service life. Heavier suspension compo- In this section you will find safety tips and information nents do not necessarily increase the vehicle’s GVWR. on limits to the type of towing you can reasonably do with your vehicle.
Page 378
376 STARTING AND OPERATING exceed the GVWR. Refer to “Vehicle Loading/Vehicle Gross Axle Weight Rating (GAWR) Certification Label” in “Starting and Operating” for The GAWR is the maximum capacity of the front and rear further information. axles. Distribute the load over the front and rear axles evenly.
Page 379
STARTING AND OPERATING 377 Frontal Area Weight-Distributing Hitch The frontal area is the maximum height multiplied by the A weight-distributing system works by applying lever- maximum width of the front of a trailer. age through spring (load) bars. They are typically used for heavier loads, to distribute trailer tongue weight to Trailer Sway Control the tow vehicle’s front axle and the trailer axle(s).
378 STARTING AND OPERATING Trailer Hitch Classification Trailer Hitch Classification Definitions Your vehicle may be factory equipped for safe towing of Class Max. Trailer Hitch Industry trailers weighing over 2,000 lbs (907 kg) with the optional Standards Trailer Tow Prep Package. See your authorized dealer for Class I - Light Duty 2,000 lbs (907 kg) package content.
STARTING AND OPERATING 379 Trailer Towing Weights (Maximum Trailer Weight Ratings) The following chart provides the maximum trailer weight ratings towable for your given drivetrain. Engine/Transmission Frontal Area Max. GTW (Gross Trailer Wt.) Max. Tongue Wt. (See Note) 2.0L Auto/Man 22 sq ft (2.04 sq m) 1,000 lbs (450 kg) 100 lbs (45 kg)
380 STARTING AND OPERATING Trailer And Tongue Weight Always load a trailer with 60% to 65% of the weight in the front of the trailer. This places 10% to 15% of the Gross Trailer Weight (GTW) on the tow hitch of your vehicle.
STARTING AND OPERATING 381 NOTE: Remember that everything put into or on the CAUTION! (Continued) trailer adds to the load on your vehicle. Also, additional • Then, during the first 500 miles (805 km) that a factory-installed options, or authorized dealer-installed trailer is towed, do not drive over 50 mph options, must be considered as part of the total load on (80 km/h) and do not make starts at full throttle.
Page 384
382 STARTING AND OPERATING WARNING! (Continued) WARNING! (Continued) • Make certain that the load is secured in the trailer • Vehicles with trailers should not be parked on a and will not shift during travel. When trailering grade. When parking, apply the parking brake on cargo that is not fully secured, dynamic load shifts the tow vehicle.
Page 385
STARTING AND OPERATING 383 Towing Requirements – Tires replacement procedures. Replacing tires with a higher load carrying capacity will not increase the vehicle’s − Do not attempt to tow a trailer while using a compact GVWR and GAWR limits. spare tire. Towing Requirements –...
Page 386
384 STARTING AND OPERATING CAUTION! WARNING! (Continued) • Towing any trailer will increase your stopping If the trailer weighs more than 1,000 lbs (454 kg) distance. When towing you should allow for addi- loaded, it should have its own brakes and they tional space between your vehicle and the vehicle should be of adequate capacity.
Page 387
STARTING AND OPERATING 385 The electrical connections are all complete to the vehicle but you must mate the harness to a trailer connector. Refer to the following illustrations. Seven-Pin Connector 1 — Battery 5 — Ground 2 — Backup Lamps 6 —...
386 STARTING AND OPERATING Towing Tips − When using the speed control, if you experience speed Before setting out on a trip, practice turning, stopping drops greater than 10 mph (16 km/h), disengage until and backing the trailer in an area away from heavy you can get back to cruising speed.
STARTING AND OPERATING 387 RECREATIONAL TOWING (BEHIND MOTORHOME, ETC.) Towing Condition Wheels OFF The Manual Transmission Automatic Transmission Ground Flat Tow None NOT ALLOWED • Transmission in NEUTRAL • Key in ACC Front OK (FWD Only) NOT ALLOWED Dolly Tow Rear NOT ALLOWED NOT ALLOWED...
Page 390
388 STARTING AND OPERATING NOTE: Vehicles equipped with manual transmissions CAUTION! may be recreationally towed (flat towed) at any legal • Do not flat tow any vehicle equipped with an highway speed, for any distance, if the manual transmis- sion is in NEUTRAL and the ignition key is in the ACC automatic transmission.
390 WHAT TO DO IN EMERGENCIES HAZARD WARNING FLASHERS IF YOUR ENGINE OVERHEATS The Hazard Warning flasher switch is located on the In any of the following situations, you can reduce the instrument panel, below the radio. potential for overheating by taking the appropriate ac- tion.
WHAT TO DO IN EMERGENCIES 391 CAUTION! WARNING! Driving with a hot cooling system could damage You or others can be badly burned by hot engine your vehicle. If the pointer rises to the H (red) mark, coolant (antifreeze) or steam from your radiator. If the instrument cluster will sound a chime.
392 WHAT TO DO IN EMERGENCIES JACKING AND TIRE CHANGING WARNING! (Continued) • Never start or run the engine while the vehicle is WARNING! on a jack. • Do not attempt to change a tire on the side of the •...
WHAT TO DO IN EMERGENCIES 393 Jack Location Spare Tire Removal The jack and jack-handle are stowed under the load floor Lift up the load floor cover and remove the hold down. in the cargo area. Preparations For Jacking 1. Park the vehicle on a firm level surface, avoiding ice or slippery areas.
394 WHAT TO DO IN EMERGENCIES 5. Turn OFF the ignition. WARNING! (Continued) 6. Block both the front and rear of the • Always park on a firm, level surface as far from wheel diagonally opposite the jacking the edge of the roadway as possible before raising position.
Page 397
WHAT TO DO IN EMERGENCIES 395 WARNING! (Continued) CAUTION! • If working on or near a roadway, be extremely Do not attempt to raise the vehicle by jacking on careful of motor traffic. locations other than those indicated in the Jacking •...
Page 398
396 WHAT TO DO IN EMERGENCIES NOTE: Refer to “Tires — General Information” in “Starting And Operating” for further information about the spare tire, it’s use, and operation. 1. Remove the scissors jack and lug wrench from the spare wheel as an assembly. Turn the jack screw to the left to loosen the lug wrench and remove the wrench from the jack assembly.
Page 399
WHAT TO DO IN EMERGENCIES 397 3. Turn the jack screw to the left until the jack can be placed under the jacking location. Once the jack is positioned, turn the jack screw to the right until the jack head is properly engaged with the lift area closest to the wheel to be changed.
Page 400
398 WHAT TO DO IN EMERGENCIES 5. Remove the wheel nuts and pull the wheel and wheel covers, where applicable, off the hub. Install the spare wheel and wheel nuts with the cone shaped end of the nuts toward the wheel. Lightly tighten the nuts. WARNING! To avoid the risk of forcing the vehicle off the jack, do not tighten the wheel nuts fully until the vehicle...
Page 401
WHAT TO DO IN EMERGENCIES 399 NOTE: The wheel cover is held on the wheel by the WARNING! wheel nuts. When reinstalling the original wheel, prop- erly align the wheel cover to the valve stem, place the A loose tire or jack thrown forward in a collision or wheel cover onto the wheel, then install the wheel nuts.
400 WHAT TO DO IN EMERGENCIES Road Tire Installation Vehicles Equipped With Wheel Covers 1. Mount the road tire on the axle. 2. To ease the installation process for steel wheels with wheel covers, install two lug nuts on the mounting studs which are on each side of the valve stem.
Page 403
WHAT TO DO IN EMERGENCIES 401 3. Align the valve notch in the wheel cover with the 6. Finish tightening the lug nuts. Push down on the valve stem on the wheel. Install the cover by hand, wrench while at the end of the handle for increased snapping the cover over the two lug nuts.
402 WHAT TO DO IN EMERGENCIES 5. After 25 miles (40 km) check the lug nut torque with a WARNING! torque wrench to ensure that all lug nuts are properly seated against the wheel. To avoid the risk of forcing the vehicle off the jack, do not tighten the lug nuts fully until the vehicle is JUMP-STARTING PROCEDURES lowered to the ground.
WHAT TO DO IN EMERGENCIES 403 CAUTION! Do not use a portable battery booster pack or any other booster source with a system voltage greater than 12 Volts or damage to the battery, starter motor, alternator or electrical system may occur. WARNING! Do not attempt jump-starting if the battery is frozen.
Page 406
404 WHAT TO DO IN EMERGENCIES WARNING! • Take care to avoid the radiator cooling fan when- ever the hood is raised. It can start anytime the ignition switch is on. You can be injured by moving fan blades. • Remove any metal jewelry such as watch bands or bracelets that might make an inadvertent electrical contact.
WHAT TO DO IN EMERGENCIES 405 3. If using another vehicle to jump-start the battery, park CAUTION! the vehicle within the jumper cables reach, set the parking brake and make sure the ignition is OFF. Failure to follow these procedures could result in damage to the charging system of the booster vehicle WARNING! or the discharged vehicle.
Page 408
406 WHAT TO DO IN EMERGENCIES 4. Connect the opposite end of the negative (-) jumper Once the engine is started, remove the jumper cables in cable to a good engine ground (exposed metal part of the the reverse sequence: discharged vehicle’s engine) away from the battery and 6.
WHAT TO DO IN EMERGENCIES 407 CAUTION! CAUTION! Accessories that can be plugged into the vehicle Racing the engine or spinning the wheels may lead to power outlets draw power from the vehicle’s battery, transmission overheating and failure. Allow the en- even when not in use (i.e., cellular phones, etc.).
408 WHAT TO DO IN EMERGENCIES CAUTION! WARNING! • When “rocking” a stuck vehicle by moving be- Fast spinning tires can be dangerous. Forces gener- tween DRIVE and REVERSE (with automatic ated by excessive wheel speeds may cause damage, or transmission) or 1st gear and Reverse (with even failure, of the axle and tires.
Page 411
WHAT TO DO IN EMERGENCIES 409 3. Turn the ignition switch to the ON/RUN position without starting the engine (engine OFF). 4. Press and maintain firm pressure on the brake pedal. 5. Using a small screwdriver or similar tool, push and hold the override release lever forward.
410 WHAT TO DO IN EMERGENCIES TOWING A DISABLED VEHICLE AUTOMATIC MANUAL Towing Condition Wheels OFF the Ground TRANSMISSION TRANSMISSION Transmission in NEU- Flat Tow NONE NOT ALLOWED TRAL Rear NOT ALLOWED NOT ALLOWED Wheel Lift or Dolly Tow Front FWD Models ONLY FWD Models ONLY Flatbed...
WHAT TO DO IN EMERGENCIES 411 • FWD vehicles can be towed with the front wheels With Ignition Key elevated. Automatic Transmission • FWD or 4WD vehicles can be towed on a flatbed truck • Front Wheel Drive (FWD) vehicles can be towed with (all wheels OFF the ground).
412 WHAT TO DO IN EMERGENCIES If the vehicle’s battery is discharged, see “Shift Lever Without The Ignition Key Override” in “What To Do In Emergencies” for instruc- Special care must be taken when the vehicle is towed tions on shifting the automatic transmission out of the with the ignition in the LOCK/OFF position.
MAINTAINING YOUR VEHICLE 417 ONBOARD DIAGNOSTIC SYSTEM — OBD II CAUTION! Your vehicle is equipped with a sophisticated onboard • Prolonged driving with the MIL on could cause diagnostic system called OBD II. This system monitors the performance of the emissions, engine, and automatic further damage to the emission control system.
418 MAINTAINING YOUR VEHICLE persists, the message will appear the next time the Normally, the OBD II system will be ready. The OBD II vehicle is started. This might indicate a damaged cap. If system may not be ready if your vehicle was recently the problem is detected twice in a row, the system will serviced, recently had a dead battery or a battery replace- turn on the MIL.
MAINTAINING YOUR VEHICLE 419 4. Approximately 15 seconds later, one of two things will Regardless of whether your vehicle’s OBD II system is happen: ready or not, if the MIL is illuminated during normal vehicle operation you should have your vehicle serviced a.
420 MAINTAINING YOUR VEHICLE DEALER SERVICE MAINTENANCE PROCEDURES Your authorized dealer has the qualified service person- The pages that follow contain the required maintenance nel, special tools, and equipment to perform all service services determined by the engineers who designed your operations in an expert manner.
MAINTAINING YOUR VEHICLE 421 fully warmed engine is shut off. Do not check oil level CAUTION! (Continued) before starting the engine after it has sat overnight. • Your vehicle has been built with improved fluids Checking engine oil level when the engine is cold will that protect the performance and durability of give you an incorrect reading.
Page 424
422 MAINTAINING YOUR VEHICLE Engine Oil Selection CAUTION! For best performance and maximum protection for all engines under all types of operating conditions, the Do not overfill the engine. Overfilling the engine manufacturer recommends engine oils that are API Cer- will cause oil aeration, which can lead to loss of oil tified and meet the requirements of Chrysler Material pressure and an increase in oil temperature.
Page 425
MAINTAINING YOUR VEHICLE 423 Synthetic Engine Oils CAUTION! You may use synthetic engine oils provided the recom- mended oil quality requirements are met, and the recom- Do not use chemical flushes in your engine oil as the mended maintenance intervals for oil and filter changes chemicals can damage your engine.
424 MAINTAINING YOUR VEHICLE Engine Oil Filter WARNING! The engine oil filter should be replaced with a new filter at every engine oil change. The air cleaner can provide a measure of protection in the case of engine backfire. Do not remove the air Engine Oil Filter Selection cleaner unless such removal is necessary for repair or All of this manufacturer’s engines have a full-flow type...
MAINTAINING YOUR VEHICLE 425 Maintenance-Free Battery WARNING! (Continued) Your vehicle is equipped with a maintenance-free battery. • Battery gas is flammable and explosive. Keep You will never have to add water, nor is periodic main- flame or sparks away from the battery. Do not use tenance required.
426 MAINTAINING YOUR VEHICLE Air Conditioner Maintenance CAUTION! For best possible performance, your air conditioner • It is essential when replacing the cables on the should be checked and serviced by an authorized dealer at the start of each warm season. This service should battery that the positive cable is attached to the include cleaning of the condenser fins and a performance positive post and the negative cable is attached to...
MAINTAINING YOUR VEHICLE 427 Protection Agency and is an ozone-saving product. How- WARNING! ever, the manufacturer recommends that air conditioning • Use only refrigerants and compressor lubricants service be performed by authorized dealers or other service facilities using recovery and recycling equipment. approved by the manufacturer for your air condi- tioning system.
428 MAINTAINING YOUR VEHICLE hood latching components to ensure proper function. from a dry windshield. Avoid using the wiper blades to When performing other underhood services, the hood remove frost or ice from the windshield. Make sure that latch, release mechanism and safety catch should be they are not frozen to the glass before turning them on to cleaned and lubricated.
MAINTAINING YOUR VEHICLE 429 When refilling the washer fluid reservoir, take some Exhaust System washer fluid and apply it to a cloth or towel and wipe The best protection against carbon monoxide entry into clean the wiper blades, this will help blade performance. the vehicle body is a properly maintained engine exhaust To prevent freeze-up of your windshield washer system system.
Page 432
430 MAINTAINING YOUR VEHICLE WARNING! CAUTION! • Exhaust gases can injure or kill. They contain • The catalytic converter requires the use of un- carbon monoxide (CO), which is colorless and leaded fuel only. Leaded gasoline will destroy the odorless. Breathing it can make you unconscious effectiveness of the catalyst as an emissions con- and can eventually poison you.
Page 433
MAINTAINING YOUR VEHICLE 431 Under normal operating conditions, the catalytic con- To minimize the possibility of catalytic converter dam- verter will not require maintenance. However, it is im- age: portant to keep the engine properly tuned to assure • Do not shut off the engine or interrupt the ignition, proper catalyst operation and prevent possible catalyst when the transmission is in gear and the vehicle is in damage.
432 MAINTAINING YOUR VEHICLE Cooling System rusty in appearance, the system should be drained, flushed and refilled with fresh engine coolant (anti- WARNING! freeze). Check the front of the A/C condenser for any accumulation of bugs, leaves, etc. If dirty, clean by gently •...
Page 435
MAINTAINING YOUR VEHICLE 433 Selection Of Coolant CAUTION! (Continued) Refer to “Fluids, Lubricants, and Genuine Parts” in • Do not use water alone or alcohol based engine “Maintaining Your Vehicle” for further information. coolant (antifreeze) products. Do not use addi- tional rust inhibitors or antirust products, as they CAUTION! may not be compatible with the radiator engine...
Page 436
434 MAINTAINING YOUR VEHICLE vehicle. Please review these recommendations for using Please note that it is the owner’s responsibility to main- Hybrid Organic Additive Technology (HOAT) engine tain the proper level of protection against freezing ac- coolant (antifreeze). cording to the temperatures occurring in the area where the vehicle is operated.
Page 437
MAINTAINING YOUR VEHICLE 435 rules for your community. To prevent ingestion by ani- WARNING! mals or children do not store ethylene glycol-based • The warning words “DO NOT OPEN HOT” on engine coolant (antifreeze) in open containers or allow it to remain in puddles on the ground.
Page 438
436 MAINTAINING YOUR VEHICLE • Check the coolant freeze point in the radiator and in long as the engine operating temperature is satisfactory, the coolant bottle need only be checked once a month. the coolant recovery bottle. If engine coolant (anti- freeze) needs to be added, the contents of the coolant When additional engine coolant (antifreeze) is needed to recovery bottle must also be protected against freez-...
MAINTAINING YOUR VEHICLE 437 • Keep the front of the radiator clean. If your vehicle is WARNING! equipped with air conditioning, keep the front of the condenser clean. Riding the brakes can lead to brake failure and possibly a collision. Driving with your foot resting or •...
Page 440
438 MAINTAINING YOUR VEHICLE when the pads are replaced. However, low fluid level WARNING! may be caused by a leak and a checkup may be needed. • Use only manufacturer’s recommended brake NOTE: If your vehicle is equipped with a manual fluid.
Page 441
MAINTAINING YOUR VEHICLE 439 WARNING! (Continued) WARNING! (Continued) • To avoid contamination from foreign matter or • Do not allow petroleum based fluid to contami- moisture, use only new brake fluid or fluid that nate the brake fluid. Brake seal components could has been in a tightly closed container.
440 MAINTAINING YOUR VEHICLE Automatic Transmission (CVT) – If Equipped Special Additives Do not add any materials (other than leak detection dyes) Selection Of Lubricant to Continuously Variable Transmission (CVT) Fluid It is important that the proper lubricant is used in the (CVTF+4 ).
MAINTAINING YOUR VEHICLE 441 level checked immediately. Operation with incorrect Frequency Of Fluid Change fluid level can cause severe transmission damage. Under normal operating conditions, the fluid installed at the factory will give satisfactory lubrication for the life of Fluid And Filter Changes the vehicle.
442 MAINTAINING YOUR VEHICLE fill plug. The fluid level should be maintained between the fill plug. The fluid level should be maintained be- the bottom of the fill hole to 1/8 in (4 mm) below the fill tween the bottom of the fill hole to 1/8 in (4 mm) below hole.
Page 445
MAINTAINING YOUR VEHICLE 443 hot or cold weather and other extreme conditions will Washing have an adverse effect on paint, metal trim, and under- • Wash your vehicle regularly. Always wash your ve- body protection. hicle in the shade using MOPAR Car Wash or a mild The following maintenance recommendations will enable car wash soap, and rinse the panels completely with you to obtain maximum benefit from the corrosion...
Page 446
444 MAINTAINING YOUR VEHICLE • If you detect any stone chips or scratches in the paint, CAUTION! touch them up immediately. The cost of such repairs is • Do not use abrasive or strong cleaning materials considered the responsibility of the owner. such as steel wool or scouring powder, which will •...
Page 447
MAINTAINING YOUR VEHICLE 445 Wheel And Wheel Trim Care Stain Repel Fabric Cleaning Procedure – If Equipped • All wheels and wheel trim, especially aluminum and Stain Repel seats may be cleaned in the following man- chrome plated wheels, should be cleaned regularly ner: with a mild soap and water to prevent corrosion.
Page 448
446 MAINTAINING YOUR VEHICLE Interior Care WARNING! Use MOPAR Total Clean or equivalent to clean fabric upholstery and carpeting. Do not use volatile solvents for cleaning purposes. Many are potentially flammable, and if used in Use MOPAR Total Clean or equivalent to clean vinyl closed areas, they may cause respiratory harm.
Page 449
MAINTAINING YOUR VEHICLE 447 Glass Surfaces Instrument Panel Bezels All glass surfaces should be cleaned on a regular basis CAUTION! with MOPAR Glass Cleaner or any commercial household-type glass cleaner. Never use an abrasive type When installing hanging air fresheners in your ve- cleaner.
448 MAINTAINING YOUR VEHICLE Seat Belt Maintenance Do not bleach, dye or clean the seat belts with chemical solvents or abrasive cleaners. This will weaken the fabric. Sun damage can also weaken the fabric. If the seat belts need cleaning, use a mild soap solution or lukewarm water.
Page 451
MAINTAINING YOUR VEHICLE 449 Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse 10 Amp Rear Center Brake 20 Amp Power Locks/Interior Light Switch Yellow Lighting 10 Amp Ignition Switch/ 15 Amp Power Outlet Occupant Classifica- Lt Blue tion Module 20 Amp 115V AC Inverter –...
Page 452
450 MAINTAINING YOUR VEHICLE Cavity Cartridge Mini- Description Cavity Cartridge Mini- Description Fuse Fuse Fuse Fuse 40 Amp Auto Shutdown Relay 15 Amp Auto Shutdown Relay Green Lt Blue 20 Amp Radio Amplifiers 10 Amp Airbag Control Yellow Module 15 Amp Radio 10 Amp Airbag Control...
Page 453
MAINTAINING YOUR VEHICLE 451 Cavity Cartridge Mini- Description CAUTION! Fuse Fuse • When installing the IPM cover, it is important to 10 Amp J1962 Conn/ ensure the cover is properly positioned and fully Powertrain Control latched. Failure to do so may allow water to get Module into the IPM, and possibly result in an electrical 30 Amp...
452 MAINTAINING YOUR VEHICLE VEHICLE STORAGE REPLACEMENT BULBS If you will not be using your vehicle for more than All the inside bulbs are brass or glass wedge base. 21 days, you may want to take steps to preserve your Aluminum base bulbs are not approved and should not battery.
MAINTAINING YOUR VEHICLE 453 BULB REPLACEMENT Fog Lamps Refer to the Service Manual or see your authorized dealer Headlamps for bulb replacement. 1. Raise the hood and locate the connector behind the CAUTION! headlamp. Do not touch the new bulb with your fingers. Oil 2.
454 MAINTAINING YOUR VEHICLE License Lamps 3. Pull the bulb from the socket. 1. Use a screw driver to gently pry against the side of the Center High-Mounted Stoplamp snap tab to remove the lamp from the liftgate. This light is an LED assembly. See your authorized dealer for replacement.
MAINTAINING YOUR VEHICLE 455 FLUIDS, LUBRICANTS, AND GENUINE PARTS Engine Component Fluid, Lubricant, or Genuine Part Engine Coolant MOPAR Antifreeze/Coolant 5 Year/100,000 Mile Formula HOAT (Hy- brid Organic Additive Technology) or equivalent. Engine Oil Use API Certified SAE 5W-20 Engine Oil, meeting the requirements of Chrysler Material Standard MS-6395.
Page 460
458 MAINTENANCE SCHEDULES MAINTENANCE SCHEDULE On Non-EVIC equipped vehicles, “Change Oil” will flash The Scheduled Maintenance services listed in this in the instrument cluster odometer and a single chime manual must be done at the times or mileages specified will sound, indicating that an oil change is necessary. to protect your vehicle warranty and ensure the best Based on engine operation condition, the oil change vehicle performance and reliability.
Page 461
MAINTENANCE SCHEDULES 459 • Change your engine oil more often if you drive your At Each Stop For Fuel vehicle off-road for an extended period of time. • Check the engine oil level about five minutes after a • Under no circumstances should oil change intervals fully warmed engine is shut off.
Page 462
460 MAINTENANCE SCHEDULES Once A Month At Each Oil Change • Check the tire pressure and look for unusual wear or • Change the engine oil filter. damage. • Inspect the brake hoses and lines. • Inspect the battery and clean and tighten the terminals CAUTION! as required.
Page 463
MAINTENANCE SCHEDULES 461 8,000 Miles (13,000 km) or 16,000 Miles (26,000 km) or 12 Months Maintenance Service 6 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
462 MAINTENANCE SCHEDULES 24,000 Miles (39,000 km) or 32,000 Miles (52,000 km) or 24 Months Maintenance Service 18 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 465
MAINTENANCE SCHEDULES 463 40,000 Miles (65,000 km) or 48,000 Miles (78,000 km) or 36 Months Maintenance Service 30 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 466
464 MAINTENANCE SCHEDULES 56,000 Miles (91,000 km) or 64,000 Miles (104,000 km) or 48 Months Maintenance Service 42 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 467
MAINTENANCE SCHEDULES 465 72,000 Miles (117,000 km) or 80,000 Miles (130,000 km) or 60 Months Maintenance Service 54 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 468
466 MAINTENANCE SCHEDULES 88,000 Miles (143,000 km) or 66 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 88,000 miles (143 000 km). Odometer Reading Date Repair Order #...
Page 469
MAINTENANCE SCHEDULES 467 96,000 Miles (156,000 km) or 72 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 96,000 miles (156 000 km). ❏...
Page 470
468 MAINTENANCE SCHEDULES 104,000 Miles (169,000 km) or 112,000 Miles (182,000 km) or 84 Months Maintenance Service 78 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 471
MAINTENANCE SCHEDULES 469 120,000 Miles (195,000 km) or 128,000 Miles (208,000 km) or 96 Months Maintenance Service 90 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 472
470 MAINTENANCE SCHEDULES 136,000 Miles (221,000 km) or 144,000 Miles (234,000 km) or 108 Months Maintenance Service 102 Months Maintenance Schedule ❏ Change the engine oil and engine oil filter. Service Schedule ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before ❏...
Page 473
MAINTENANCE SCHEDULES 471 152,000 Miles (247,000 km) or 114 Months Maintenance Service Schedule ❏ Change the engine oil and engine oil filter. ❏ Rotate the tires, rotate at the first sign of irregular wear, even if it occurs before 152,000 miles (247 000 km). Odometer Reading Date Repair Order #...
Page 474
472 MAINTENANCE SCHEDULES WARNING! • You can be badly injured working on or around a motor vehicle. Do only service work for which you have the knowledge and the right equipment. If you have any doubt about your ability to perform a service job, take your vehicle to a competent mechanic.
IF YOU NEED CONSUMER ASSISTANCE CONTENTS Suggestions For Obtaining Service For Your Customer Assistance For The Hearing Or Vehicle......475 Speech Impaired (TDD/TTY) .
Page 476
474 IF YOU NEED CONSUMER ASSISTANCE Department Of Transportation Uniform Tire Traction Grades ..... 481 Quality Grades ......481 Temperature Grades .
IF YOU NEED CONSUMER ASSISTANCE 475 SUGGESTIONS FOR OBTAINING SERVICE FOR the service advisor and list the items in order of priority. YOUR VEHICLE At many authorized dealers, you may obtain a rental vehicle at a minimal daily charge. If you need a rental, it Prepare For The Appointment is advisable to make these arrangements when you call If you’re having warranty work done, be sure to have the...
476 IF YOU NEED CONSUMER ASSISTANCE This is why you should always talk to an authorized Chrysler Group LLC Customer Center dealer’s service manager first. Most matters can be re- P.O. Box 21–8004 solved with this process. Auburn Hills, MI 48321–8004 Phone: (877) 426–5337 •...
IF YOU NEED CONSUMER ASSISTANCE 477 Customer Assistance For The Hearing Or Speech the manufacturer’s service contracts. If you purchased a Impaired (TDD/TTY) manufacturer’s service contract, you will receive Plan To assist customers who have hearing difficulties, the Provisions and an Owner Identification Card in the mail manufacturer has installed special TDD (Telecommuni- within three weeks of the vehicle delivery date.
478 IF YOU NEED CONSUMER ASSISTANCE We appreciate that you have made a major investment WARRANTY INFORMATION when you purchased the vehicle. An authorized dealer See the Warranty Information Booklet, located on the has also made a major investment in facilities, tools, and DVD, for the terms and provisions of Chrysler Group training to assure that you are absolutely delighted with LLC warranties applicable to this vehicle and market.
IF YOU NEED CONSUMER ASSISTANCE 479 If NHTSA receives similar complaints, it may open an In Canada investigation, and if it finds that a safety defect exists in If you believe that your vehicle has a safety defect, you a group of vehicles, it may order a recall and remedy should contact the Customer Service Department imme- campaign.
Page 482
480 IF YOU NEED CONSUMER ASSISTANCE • Service Manuals • Owner’s Manuals These comprehensive Service Manuals provide the These Owner’s Manuals have been prepared with the information that students and professional technicians assistance of service and engineering specialists to need in diagnosing/troubleshooting, problem solving, acquaint you with specific Chrysler Group LLC ve- maintaining, servicing, and repairing Chrysler Group hicles.
Page 483
IF YOU NEED CONSUMER ASSISTANCE 481 DEPARTMENT OF TRANSPORTATION UNIFORM significantly from the norm due to variations in driving TIRE QUALITY GRADES habits, service practices, and differences in road charac- The following tire grading categories were established by teristics and climate. the National Highway Traffic Safety Administration.
Page 484
482 IF YOU NEED CONSUMER ASSISTANCE Temperature Grades WARNING! The temperature grades are A (the highest), B, and C, representing the tire’s resistance to the generation of heat The temperature grade for this tire is established for and its ability to dissipate heat, when tested under a tire that is properly inflated and not overloaded.
Page 497
INDEX 495 Paint Care ......442 Pregnant Women and Seat Belts ....61 Panic Alarm .
Page 498
496 INDEX Reminder, Seat Belt ..... . . 59 Safety Checks Inside Vehicle ....86 Remote Control Safety Checks Outside Vehicle .
Page 499
INDEX 497 Rear Seat ......42 Shift Lever Override ..... . 408 Seats .
Page 500
498 INDEX Steering Temperature Gauge, Engine Coolant ..203,391 Power ......319,320 Tether Anchor, Child Restraint .
Page 501
INDEX 499 Jacking ......392 Guide ......379 Life of Tires .
Page 502
500 INDEX Transmitter Battery Service Vanity Mirrors ......99 (Remote Keyless Entry) ....25 Variance, Compass .
Page 503
INDEX 501 Wheel and Wheel Trim ....445 Windshield Defroster ... . . 87,279,280,286 Wheel and Wheel Trim Care .
Page 504
INSTALLATION OF RADIO TRANSMITTING EQUIPMENT Special design considerations are incorporated into this The antenna cable should be as short as practical and vehicle’s electronic system to provide immunity to radio routed away from the vehicle wiring when possible. Use only frequency signals.
Page 505
Chrysler Group LLC 3rd Edition Printed in U.S.A. 12MK74-126-AC...