Advertisement
Quick Links
Total pages scanned:
IWorknow:
I
Initial and Date each section below as it is completed:
Received _ Batchj
_
Scanned
Batch #
Title
....
Chassis
Product Type #
Doc Type
Date Received
Date Published
Publication
#
Pricing - Div
Pricing - Source
Figure Properties
S-E_V]-NG MACHINE
CABINET
DBO_
1260000
SERVM
[]
OWNM [] REFER
[] TECHM
[] INSTL []
PROC [] SALES r-
12-10-99
12-1-98
98100-FC
NIA
N/A
Model Numbers:
27298100490
MODEL INFORMATION
Type
Mfr Class
Status
Brand # 0934
Comments:
REG
STD
ACTIVE X
REG
SBP X
NPA
REG
STD
ACTIVE
SBP
NPA
REG
Document I 12/16/99
Advertisement
Related Manuals for Kenmore Sewing machine cabinet 272.98100.490
Summary of Contents for Kenmore Sewing machine cabinet 272.98100.490
- Page 1 Total pages scanned: IWorknow: Initial and Date each section below as it is completed: DBO_ Received _ Batchj Scanned Batch # Figure Properties Title ..S-E_V]-NG MACHINE CABINET Chassis 1260000 Product Type # Doc Type SERVM OWNM [] REFER [] TECHM [] INSTL [] PROC [] SALES r- Date Received...
- Page 2 OWNER'S MANUAL SEWING SEI_'ING MACHINE MAt;I_NE CABINET CAI_INET Model 272.98100.49_0 • ASSEMBLY • PARTS LIST IMPORTANT: Read instructions before assembling. 98100-FC...
- Page 3 Notice to Customer: TO ORDER REPLACEMENT PARTS CALL 1-800-366-7278 MANUALS DE ASAMBLEA EN ESPAI_OL. Before beginning assembly, remove all parts from the carton. Check closely with illustrations below to deter- Gracias pot comprar su gabinete de costura. Si usted necesita el "Manual en Espa_ol"...
- Page 4 Understanding How the "ARROW-LOC" Cam Fastener Works ARROW TOWARDS HOLE IN EDG! 1. Position bolt in 2. Press cam into 3. Insert bolt through 4. To lock, rotate cam pre-drilled hole and pre-drilled hole until pre-drilled hole in until tight, using turn until tight, flush with surface, edge of panel,...
- Page 5 Assembly Instructions STEP 1. Place Top and Sides on flat surface to thread the (12) Connecting Bolts into the pre-drilled holes (as shown in FIGS. 1 and 2). NOTE: <_ = Cam FIG, 1 • = Connecting Bott FIG. 2 Top Assembly Left Side Panel Right Side Panel...
- Page 6 (2) #8x1/2" Panhead Screws (as shown in FIG. 4). /_;_ " _ ack Panel STEP3. Attachthe PlatformStopperto the Back using /¢_ -_'v Platform Stopper FOLLOWING ASSEMBLY BONE WITH CABINET UPSIDE DOWN: STEP 4. Attach the Back Panel, Front assembly and Back Brace onto the Connecting Bolts in the Right Side Panel (as shown in FIG.
- Page 7 NOTE: The following assemblies should be done with the Cabinet upright. STEP5. Attach Hinges to Leaf Supports with (4) #8x5/8" Flathead Screws each, tap in Magnet with hammer, (as shown in FIG. 8B). STEP6. Attach the Leaf Support to Left Side Panel with (4) #8x5/8" Flathead Screws, (as shown in FIG. 7). Attach the Bronze Strike to Side Panel with (1) #5xl/2"...
- Page 8 Installing Sewing Machine in your new Cabinet. It may be helpful to read the directions for operating the mechanism before proceeding with the following steps. See page 7, and FIG. 12, on this page. STEP3 STEP 1. To prevent damage to Cabinet surface, place cushioning material just to the left of cut-out.
- Page 9 Operating the Mechanism in your Cabinet To move from FLATBED POSITION TO To move your machine from FREE-ARM position FREE-ARM position: (See FIG. 13, 14 and 15.) to FLATBED position: (See FIGS. 13, 14 and 15). (1.) Remove INSERT (1.) Lift and tilt machine slightly forward. (2.) Lift and tilt machine slightly backwards.
- Page 10 Wood Parts List (B)Top (A) Leaf (N) Filler Strip (E) Left Side (F) Right Side (G) Back Panel Panel (L) Back Brace REF. DESCRIPTION PART # Leaf 003000 (J) insert (Plastic) 003004 Machine Platform 003006 Hinge Rail 003007 Left Side Panel 003001 Right Side Panel 003002...
-
Page 11: Hardware Parts List
Hardware Parts List DESCRIPTION PART# 19mm Cam 000709 Connecting Bolt 002892 (A) 19mm Cam (B) Connecting Bolt (C) Rubber Bumpers Rubber Bumper 002466 Mounting Bolt 002890 1/4" Washer 000220 1/4" - 20 Wing Nut 000488 Bronze Magnet Strike 000839 Support Panel Hinge 002734 (D) Mounting Bolt (E) Washer... -
Page 12: Mechanism Parts
3-Position Mechanism Parts (FF) Left Bracket (GG) Right Hinge (HH) Left Hinge (EE) Right Bracket © (MM) 1/4" 20 Hex Nut (OO) Cotter Pin (JJ) Small Rod (LL) Platform \\ _5 \ (RR) Spring (PP) Release Lever Pad Number Item Description (SS) Plastic Spacer... - Page 13 Arrow Specialty Furniture (A Division of ARROW PRODUCTS, Inc.) P.O. Box 410, EIkhorn, Wl 53121 1-800-533-7347 12-9_ 98100-BC...