AOpen XC Cube edition EZ855 Easy Installation Manual

Easy Installation Guide
Optical Device Optical Device
S/PDIF OUT Port S/PDIF OUT Port
Phone Jack Phone Jack
Microphone Jack Microphone Jack
USB 2.0 Ports USB 2.0 Ports
Coaxial Out RCA Port
COM1 Port
Parallel Port
PS/2 Mouse Connector
PS/2 Keyboard Connector
Monitor Connector
1
2
Connect the Connect the
purple keyboard
monitor's video
connector to the cable to the blue
matching purple
monitor connector
connector at the
located at the rear
rear panel. Also panel.
connect the green
mouse connector to
the green
connector at the
rear panel.
6
5
Depending on
Connect the
the type of printer
microphone
that you have,
cable to the pink
connect the
microphone jack
printer's data cable
at the rear
to the blue-colored
panel.
parallel port as
shown in the
picture.
To learn more about AOpen XC Cube, visit us at http://xc.aopen.com.tw, http://www.aopen.com
EZ855
Optical Device Optical Device
Eject Button Eject Button
Floppy Disk Drive Floppy Disk Drive
/ Card Reader / Card Reader
Power Button Power Button
HDD Indicator HDD Indicator
IEEE1394 Port (4 pin) IEEE1394 Port (4 pin)
IEEE1394 Port IEEE1394 Port
(6 pin) (6 pin)
Voltage selector switch
(115/230V)
Power Supply Switch
Power Connector
IEEE1394 Port (6 pin)
Ethernet Network
Connector (RJ45)
Line-In Jack (SUR)
Line-Out Jack (L/R)
Microphone Jack (C/B)
USB 2.0 Ports
S/PDIF IN Port
3
4
Plug the RJ45
Connect the
cable into the
speakers' audio
network jack cable to the light
(recognizable by
blue speaker jack at
an icon with three the rear panel. Also
tiny computers).
insert the speakers'
power plug into a
properly grounded
AC wall socket.
8
7
Connect the
Connect the
other end of the
power cord to
power cord to the
the system's
AC wall socket, and
power connector
press the power
as shown.
button to boot up
your system.
P/N:49.EZ802.011 Doc.no:EZ855-EG-E0410A
UX855GME
AUX_IN
Front Audio
AC'97 CODEC
JP4 & JP5
AUX_IN Jumper
CD_IN
PCI slot
AGP 4X
IDE Connector x 2
(ATA33/ 66/100)
JP14 CMOS
Jumper
Front Panel
Connector
CPU (Socket 479) Frequency Table CPU (Socket 479) Frequency Table
Processor Name Clock Speed FSB System Bus L2 Cache Ratio Processor Name Clock Speed
Pentium M 755 2.0 GHz 100MHz 400MHz 2MB 20 x Celeron M 360
Pentium M 745 1.8 GHz 100MHz 400MHz 2MB 18 x Celeron M 350
Pentium M 735 1.7 GHz 100MHz 400MHz 2MB 17 x Celeron M 340
Pentium M 725 1.6 GHz 100MHz 400MHz 2MB 16 x Celeron M 330
Pentium M 715 1.5 GHz 100MHz 400MHz 2MB 15 x Celeron M 320
Pentium M 705 1.5 GHz 100MHz 400MHz 1MB 15 x Celeron M 310
Pentium M 738 1.4 GHz 100MHz 400MHz 2MB 14 x Celeron M 353
Pentium M 718 1.3 GHz 100MHz 400MHz 1MB 13 x Celeron M 333
Pentium M 733 1.1 GHz 100MHz 400MHz 2MB 11 x Note: With CPU changing rapidly, there might be faster CPU on the
market by the you received this installation guide. This table is
Pentium M 723 1.0 GHz 400MHz 2MB 10 x
100MHz
kindly for your references only.
Pentium M 713 1.1 GHz 100MHz 400MHz 1MB 11 x
Cooler Installation Cooler Installation
1
Push four iron plates up a bit
and then put CPU cooler firmly
2
onto the CPU retention module.
Press four iron plates
downward till you hear a "chip"
sound.
Note:
For Optimized heat-
dissipating, the fan should be
placed next to the slots onboard.
To learn more about AOpen XC Cube, visit us at http://xc.aopen.com.tw, http://www.aopen.com
P/N:49.EZ802.011 Doc.no:EZ855-EG-E0410A
Back Panel
JP28 KB/MS
Wake_up Jumper
FDD Connector
Printer Connector
4-pin ATX Power
IEEE 1394 x 2
USB 2.0 x 4
479-pin CPU Socket
supports Intel
®
Pentium M and
®
Celeron M CPU
®
Intel 855GME +
ICH4-M Chipset
CPUFAN1
DDR333/266/200
DIMMx 2
Max. 2 GB
ATX Power
FSB System Bus L2 Cache Ratio
1.4 GHz 100MHz 400MHz 1MB 14 x
1.3 GHz 100MHz 400MHz 1MB 13 x
1.5 GHz 100MHz 400MHz 512KB 15 x
1.4 GHz 100MHz 400MHz 512KB 14 x
1.3 GHz 100MHz 400MHz 512KB 13 x
1.2 GHz 100MHz 400MHz 512KB 12 x
900 MHz 100MHz 400MHz 512KB 9 x
900 MHz 100MHz 400MHz 512KB 9 x
Technical Technical
Notice Notice
*
UX855GME is based on
3
powerful Intel 855GME
Connect the fan cable onto
chipset, which provides
the CPU FAN connector onboard.
integrated graphics
capabilty. Because i855GME
is designed for LVDS ( low
voltage differential signal
interface ) use, there will be
the possibility that the
monitor won't work properly
after powering on. If this
condition happens, please
press < Ctrl + Alt + F1 >
concurrently to enable the
monitor after hearing the
"Welcome Effect" of the OS.