Related Manuals for Bosch AG40-85
Summary of Contents for Bosch AG40-85
- Page 1 AG40-85 AG40-85P AG40-85PD AG40-11P AG40-11PD AG50-10 AG50-11VS AG50-11VSPD AG50-125PD AG60-125 AG60-125PD...
-
Page 2: General Power Tool Safety Warnings
General Power Tool Safety Warnings Read all safety warnings and all instructions. SAVE ALL WARNINGS AND INSTRUCTIONS FOR FUTURE REFERENCE Work area safety Keep work area clean and well lit. If an extension cord is necessary, a cord Do not operate power tools in explosive with adequate size conductors that is atmospheres, such as in the presence of capable of carrying the current necessary... - Page 3 Power tool use and care Keep handles dry, clean and free from oil and grease. Do not force the power tool. Use the correct power tool for your application. Use clamps or other practical way to secure and support the workpiece to a stable platform.
- Page 4 Develop a periodic maintenance schedule at maximum no-load speed for one minute. for your tool. Wear personal protective equipment. Depending on application, use face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing protectors, gloves and workshop apron Safety Warnings Common for Grinding, capable of stopping small abrasive or Sanding, Wire Brushing, and Abrasive...
- Page 5 direct guard opening or particles toward Never place your hand near the rotating your body. accessory. A type 27 guard must be used with all Do not position your body in the area where grinding wheels, bonded body sanding flap power tool will move if kickback occurs.
- Page 6 Additional Safety Warnings Specific for Abrasive Cutting-Off Operations: Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make A guard may not be used for all sanding an excessive depth of cut. operations. Do not discard guard when not in use.
- Page 7 Symbols IMPORTANT: Symbol Name Designation/Explanation...
- Page 8 Symbols (continued) IMPORTANT:...
- Page 9 Angle Grinders with Paddle Switch AG40-85P AG40-11P Model number & AG40-85PD & AG40-11PD AG50-11VSPD AG50-125PD AG60-125PD...
- Page 10 Angle Grinders with Slide Switch Model number AG40-85 AG50-10 AG50-11VS AG60-125...
- Page 11 Application Model number AG40-85 AG50-10 AG50-11VS AG60-125 AG40-85P(D) Model number AG40-11P(D) AG50-11VSPD AG50-125PD AG60-125PD Do not use Type 11 abrasive (cup) wheels with this tool.
-
Page 12: Assembly Instructions
Functional Descriptions Electronic Clutch: Overload Protection: Constant Response Circuitry: Soft Start: Variable Speed: Automatic Restart Protection: Assembly Instructions Lock Nut & Backing Flange Installing Side Handle Hand Shield... - Page 13 Installing Wheel Guards (Type 27 & Type 1 Wheel Guards) A Type 27 guard must be used with all grinding wheels, bonded body sanding flap discs, wire brushes and wheels. To attach guard (Fig. 5): To remove wheel guard:...
- Page 14 Abrasive Type 27 Grinding Wheel & Sanding Flap Disk Assembly To install grinding wheel or flap disk (Fig. 7): When using spin-on wheels: Do not use accessories that run eccentrically.
-
Page 15: Wheel Assembly
Abrasive Type 1 & 27 Cutting Wheel Assembly Always use type 1 cutting guard cutting operations. A type 27 wheel guard may not be used for all tool operations. Do not discard guard when not in use. To install cutting wheel (Fig. 9):... - Page 16 Concrete Dust Extraction Attachment for Surfacing Grinding Assembly A type 27 grinding wheel guard may not be used for all tool operations. Do not discard guard when not in use. Dust Extraction Attachment is not a guard, do not use with bonded abrasive wheels. To install concrete dust extraction attachment (Fig.
- Page 17 Sanding Assembly A type 27 wheel guard may not be used for all tool operations. Do not discard guard when not in use. To install backing pad and sanding disc (Fig. 11): Wire Cup Brush Assembly A type 27 wheel guard may not be used for all tool operations.
- Page 18 Masonry Cutting Guard Assembly A type 27 grinding wheel guard may not be used for all tool operations. Do not discard guard when not in use. Rotate gearbox (Fig. 13): Installing Masonry Type 1 Cutting Guard:...
- Page 19 Installing dry diamond wheel (Fig. 15): Wire Wheel Assembly To install wire wheel (Fig. 16):...
-
Page 20: Operating Instructions
Operating Instructions If the “Lock-ON” button is continuously being depressed, the trigger cannot be released. Never leave the trigger locked "ON". Before plugging the tool in, check that the trigger lock is "OFF". Be aware of the location and setting of the switch "Lock-ON"... - Page 21 Metal Grinding Tip: Metal Cutting A Type 1 wheel guard may not be included with this tool but is required when using a cutting wheel.
- Page 22 Masonry / Concrete Cutting Tip:...
- Page 23 Concrete Surfacing Tip: Sanding Tips:...
- Page 24 Wire Brush (Wheels and Cups) WIRE WHEEL BRUSH Tip: WIRE CUP BRUSH...
-
Page 25: Extension Cords
Maintenance Service Preventive maintenance performed by unauthorized personnel may result in misplacing of internal wires and components which could To avoid accidents always cause serious hazard. disconnect the tool from the power supply before cleaning or performing any maintenance. Always wear safety goggles when cleaning tools with compressed air. - Page 34 Meuleuses d’angles avec interrupteur à palette...
- Page 35 Angle Grinders with Slide Switch...
- Page 36 Application...
- Page 37 Descriptions fonctionnelles...
- Page 45 Consignes d’utilisation...
- Page 49 BROSSE MÉTALLIQUE (TYPE MEULE) BROSSE MÉTALLIQUE (TYPE COUPELLE)
- Page 59 Angle Grinders with Paddle Switch...
- Page 60 Angle Grinders with Slide Switch...
- Page 61 Application...
- Page 62 Descripciones funcionales...
- Page 70 Instrucciones de uso...
- Page 74 CEPILLO DE RUEDA DE ALAMBRE CEPILLO ACOPADO DE ALAMBRE...
- Page 76 2610025308...