Register your product and get support at www.philips.com/welcome AC4002 AC4004 User manual...
English introduction Congratulations on your purchase and welcome to Philips! To fully benefit from the support that Philips offers, register your product at www.philips. com/welcome. With this new bedroom air purifier you breathe cleaner air. For the best results, place the bedroom air purifier in a room where you spend most of your time, e.g.
If the mains cord is damaged, you must have it replaced by Philips, a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard.
Make sure all filters are properly installed before you switch on the appliance. Only use the original Philips filters specially intended for this appliance. Do not use any other filters. Avoid knocking against the appliance (the air inlet and outlet in particular) with hard objects.
English Place your fingers in the recesses of the side panels and gently pull the bottom of the front panel towards you. Then lift the hooks at the top of the panel out of the top of the appliance. To remove the pre-filter, grab the two projections and pull the filter towards you.
English Put filter 3 (activated carbon filter) back into the appliance. AC4004 only: attach filter 2 (multi-care filter) to the back of filter 1 (pre-filter). Note: Make sure that the front of filter 2 (multi-care filter), that is the side with the tag, points towards the pre-filter.
Deep purple good Air quality indication Purple fair Colour Air quality Blue very good AC4002: AiR QUAliTY lights Deep purple good Purple fair Colour Air quality Blue very good Deep purple To switch off the air quality light ring, press the AIR QUALITY button.
English Note: When the appliance is operating in another mode and you want to activate the auto mode, simply press the AUTO button. , The AUTO light and one of the FAN SPEED lights go on. The FAN SPEED light indicates at which fan speed the appliance is operating. Note: When the air quality is very good and the fan speed operates at a very low fan speed, the FAN SPEED light for the lowest speed level does not go on.
English When you choose a fan speed manually (see section ‘Fan speed’ in this chapter). In this case, one of the FAN SPEED lights, the TIMER light and one of the HOUR lights are on. In combination with the SLEEP mode (see section ‘Sleep mode’ in this chapter).
adjust the sensitivity of the air quality sensor. When it is set to a higher sensitivity level, the appliance already starts cleaning the air at lower English pollution levels to make the air even cleaner. There are 3 sensitivity levels: extra sensitive standard sensitive...
English Clean the pre-filter when the filter cleaning light flashes to ensure optimal functioning of the appliance. Unplug the appliance. Place your fingers in the recesses of the side panels and gently pull the bottom of the front panel towards you. Then lift the hooks at the top of the panel out of the top of the appliance.
English To reattach the front panel, insert the two hooks into the top of the appliance first (1). Then push the panel against the body of the appliance (2). Put the plug in the wall socket. Press and hold the reset button for filter 1 (the button below the filter cleaning light) for 2 seconds to reset the appliance.
English Filter replacement Filter maintenance When one of the filters is almost full and has to be cleaned or replaced, the corresponding light or lights (the pre-filter cleaning light or one of the filter replacement lights together with the ‘REPLACE FILTER’ light) start to flash.
If you do not replace the filter in time, the appliance stops operating approx. 2 weeks after the filter replacement light started flashing.When the English appliance is locked, it does not operate until you have replaced the full filter and pressed the reset button. Note: The time between the filter replacement signal and the locking of the Note: When filter replacement lights 2 or 3/4 and REPLACE FILTER on the appliance varies, depending on how often you use the appliance.
English To remove filter 3 (activated carbon filter), grab its tag and pull it towards you. To remove filter 4 (HEPA filter), grab its tag and pull it towards you. Discard the filter that has to be replaced and unpack the new filter. Put filter 4 (HEPA filter) back into the appliance.
English Put filter 1 (pre-filter) back into the appliance. Note: Make sure that the side with the two projections points towards you. Note: Make sure that all hooks are properly attached to the appliance. To reattach the front panel, insert the two hooks into the top of the appliance first (1).
By doing this, you help to preserve the environment. guarantee and service If you need information or if you have a problem, please visit the Philips website at www.philips.com or contact the Philips Consumer Care Centre in your country (you find its phone number in the worldwide guarantee leaflet).
There is a problem with the air quality sensor of the appliance. Please keep flashing and the contact the Philips Consumer Care Centre in your country (you find its appliance does not work. phone number in the worldwide guarantee leaflet). If there is no Consumer Care Centre in your country, go to your local Philips dealer.
Contact the Consumer Care Centre in your country (you find its ring flashes blue, all other phone number in the worldwide guarantee leaflet). If there is no Consumer lights are out. Care Centre in your country, go to your local Philips dealer.
© 2012 Koninklijke Philips Electronics N.V. All rights reserved. 4222 002 73127 12172...