Display System Owners Manual Customer Service Center • N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A. Models 89225 & 89226 WARNING! READ AND UNDERSTAND REQUIRED TOOLS AND OPERATOR'S MANUAL MATERIALS: BEFORE USING THIS UNIT. • 2 People •...
Page 2
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary.
NOTICE TO ASSEMBLERS ALL Huffy Sports Basketball Systems, including those used for DISPLAYS, MUST be assembled and ballasted with sand or water according to the instructions. Failure to follow instructions could result in SERIOUS INJURY. It is NOT acceptable to devise a makeshift weight system.
Page 4
PARTS LIST (See Hardware Identifier) Item Qty. Part No. Description Item Qty. Part No. Description 900033 Back Bracket 203795 Nut, Slam Jam 203796 T-Bolt, 3/8-16 x 5 201125 Spring, Rathet return 200318 Bracket 900103 Bracket, Backboard Support 203472 Spring 200874 Spacer, Steel .402 I.D.x.50 O.D.x1.5 Long 201651 Spacer, .50 I.D.
Page 6
Install display boards in the marked locations. Each mounting location consists of a mounting pole stub with the following dimensions: Height = 8”, O.D. = 3 3/8”, I.D. = 3 1/8” (arrows indicate direction the board is facing). Display Stand - Top View 3-1/2"...
Page 7
At corner locations 1, 2, and 3 install the display pole to the mounting pole stub. If required, secure the display pole by sliding the display wedge (12) into position as shown. To lock the display pole in place, tighten the set screw (13 or 39). 39: QTY 1 12: QTY 3 13: QTY 2...
Page 8
ELEVATOR ASSEMBLY - Corner Location 1 Attach spacers (51, 52) to pole mount Install pole mount bracket (49) with carriage bracket (49) with bolts (24), washers (30), bolts (16) as shown. and nuts (17) as shown. IMPORTANT! Tighten flange nuts (8) completely. Tighten until washers (30) no longer move.
Page 9
STEEL FRAME ACRYLIC BACKBOARD ASSEMBLY - Corner Location 1 Attach backboard support brackets (37) to the backboard frame using bolts (24), spacers (38), and nuts (17) as shown Attach lower elevator tubes (29) to backboard support brackets (37) using spacers (59), bolt (27), and nut (42) as shown.
Page 10
Attach upper elevator tubes (21) to backboard support brackets (37) using spacers (59), bolt (27), and nut (42) as shown. Attach backboard assembly to pole section (11). Install pole cap (43). WARNING! USE CAUTION; ELEVATOR ASSEMBLY IS HEAVY. TWO PEOPLE REQUIRED FOR THIS PROCEDURE.
Page 11
Attach adjustment rod (47) to lower elevator Insert handle assembly through pole tubes (29) using bolt (27) spacer (59) and nut mount assembly as shown. Lock pole (42) as shown. assembly in place at the 10’ (3.05m) mark with pin (55). P/N 21154401 01/04...
Page 12
• Fit rim (58) securely into bracket (1) as shown. • Install reinforcement bracket (3) onto “T” bolt (2) as shown. • Install spring (4) onto “T” bolt (2) as shown. • Install special nut (35) and washer (22) onto “T” bolt (2). NOTE: Tighten nut (35) until flush with end of "T"...
Page 13
44” FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 2 Correctly identify each pole section. ONLY THE TOP POLE SECTION (14) IS USED IN THIS ASSEMBLY. MIDDLE POLE 43” TOP POLE 31” BOTTOM POLE 43” Fit spacer (15) into pawl (19). Then continue to assemble as shown. Tighten completely. Identify elevator tubes (21).
Page 14
Assemble elevator tubes (21) to ratchet (28) and backboard brackets (23) using bolts (20), spacers (5, & 40), and nuts (42) as shown. Tighten completely. IMPORTANT!: It is necessary for all parts to be LEVER installed properly for this mechanism to work safely and BROOM properly.
Page 15
Insert “T” bolt (2) through Slam Jam bracket (1) as shown. Secure Slam Jam bracket (1) and backboard bracket (23) assemblies to backboard. Bend upper halves of backboard brackets (23) to line up with holes in backboard and secure with bolts (44 & 7) and nuts (8). Tighten completely.
Page 16
Attach upper and lower elevator tubes (21) to top pole section (14) using bolts (20) and nuts (42) as shown. Attach pole cap (41) as shown. WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE.
Page 17
FAN MOLDED PLASTIC BOARD ASSEMBLY - Corner Location 3. Correctly identify each pole section. Pole bracket will need to be lightly pressed into Poles have an identification sticker backboard ribbing. Be sure to press completely into that will be used as a reference point place.
Page 18
FAN BACKBOARD ASSEMBLY - Corner Location 4. Assemble fan backboard as shown below with a standard rim as shown. WARNING TWO PERSON MINIMUM REQUIRED FOR THIS PROCEDURE. NOT FOLLOWING RECOMMENDATION MAY RESULT IN BODILY INJURY. P/N 21154401 01/04...
Page 19
Install net clips. CLIP “ARM” WARNING! USE OF THIS PRODUCT WITHOUT PROPER INSTALLATION OF SMART CLIPS ® , OR WHEN ALL SMART CLIPS ® ARE NOT PRESENT COULD RESULT IN BODILY HARM. BE SURE TO FOLLOW CLIP “BODY” DIRECTIONS CAREFULLY. Insert one “arm”...
Page 20
Install net. SIDE VIEW NETCLIP Insert net into bottom of clip as shown. SIDE VIEW Twist net until it snaps into position. Net must be centered through clip. NETCLIP P/N 21154401 01/04...