Advertisement
7
TANK MTG.
BOLTS
WASHER
NUT
9
Before continuing, determine the type of water supply connecation you have from
the chart below and use the appropriate assembly parts required to properly
reconnect the water supply. DO NOT use plumber's putty to seal these fittings.
METAL/COPPER
FLARED TUBING
LOCK NUT
CONE
WASHER
COUPLING
NUT
WATER
SHUT-OFF
These parts must be used as
illustrated to insure water-tight
connection. Use of existing
coupling nut may result in water
leakage. Water supply tube or
pipe must extend at least 1/2"
inside threaded shank of valve
(does not apply to flanged tubing).
CAUTION: DO NOT USE
CONE WASHER WITH
PLASTIC SUPPLY LINE.
Repair parts are determined by toilet tank number which can be found marked inside tank.
NOTE: "XXX" represents color or trim finish options. Specify when ordering.
PART NO.
7381047-200
7381049-200
4142-016.XXX
4142.801.XXX
735133-400.XXX
3481.016.XXX
3483.016.XXX
3701.016.XXX
3703.016.XXX
034783-XXX0A
034602-0070A
7381054-100
7381053-100
7381052-100
7301320-100
034783-XXX0A
735133-401.XXX
603111-0030A
INSTALL TANK
a. Install large rubber gasket over threaded
outlet on bottom of tank and lower tank onto bowl
so that tapered end of gasket fits evenly into bowl
water inlet opening, and tank mounting bolts go
SPONGE
WASHER
through mounting holes. Secure with metal
washers and nuts.
b. With tank parallel to wall, alternately tighten
nuts until tank is snugged down evenly against
bowl surface.
!
CAUTION: DO NOT OVERTIGHTEN
NUTS MORE THAN REQUIRED
METAL FLANGED
METAL SPIRAL
TUBING
TUBING
LOCK NUT
EXISTING
WASHER
EXISTING
COUPLING
NUT
WATER
SHUT-OFF
Use existing
Use existing spiral cone
coupling nut
washer. Fluidmaster
and washer.
cone washer may not
seal completely on
spiral type supply line.
CAUTION: Overtightening of
LOCK NUT or COUPLING NUT
could result in breakage and
potential flooding.
REPAIR PARTS LIST
DESCRIPTION
TRIP LEVER ASSEMBLY LH
TRIP LEVER ASSEMBLY, WDI PRESSURE ASSIST, RH
TANK (COMPLETE WITH COUPLING COMPONENTS AND TANK TRIM)
TANK (COMPLETE WITH COUPLING COMPONENTS AND RH TANK TRIM)
TANK COVER
BOWL, ELONGATED 15"
BOWL, ELONGATED 16-1/2"H
BOWL, ELONGATED 15"
BOWL, ELONGATED 16-1/2" (419mm)
BOLT CAP COVER KIT (INCL TWO COVERS/WASHERS)
COUPLING GASKET
LOWER SUPPLY ASSEMBLY
UPPER SUPPLY ASSEMBLY
VALVE CARTRIDGE ASSEMBLY
TANK COUPLING KIT
BOLTS AND CAPS
TANK COVER FOR LOCKING DEVICE
COVER LOCKING DEVICE KIT
FOR A SNUG FIT!
VINYL/BRAIDED
CONNECTOR
LOCK NUT
LOCK NUT
EXISTING
COUPLING
CONE
NUT
WASHER
COUPLING
NUT
WATER
WATER
SHUT-OFF
SHUT-OFF
Captive cone
washers already
included. No
additional
washers needed.
- 3 -
8
INSTALL TOILET SEAT
Install toilet seat in accordance
with manufacturer's directions.
10
ADJUSTMENTS
The flushometer tank is designed and
factory-adjusted to provide a
consistent, safe seal depth in the
bowl after each flush. Field refill
adjustment is not required. The refill
has been preset and locked.
TOILET
7 3 01 3 1 2- 10 0
Advertisement
