American Standard 3125.016.020 - 3125.016.020 Yorkville Right Height Pressure-Assisted Elongated Toilet Bowl Installation Instructions

INSTALLATION INSTRUCTIONS

CADET 1.6 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS
- Model 2462.016 Cadet Elongated 15"
- Model 2467.016 Cadet Elongated 16-1/2" High Bowl
YORKVILLE 1.6 GPF TWO-PIECE PRESSURE-ASSISTED TOILETS
- Model 2876.016 Yorkville Elongated 15"
- Model 2878.016 Yorkville Elongated 16-1/2" High Bowl
Thank you for selecting American Standard - the benchmark of fine quality for over 100 years. To ensure this product is
installed properly, please read these instructions carefully before you begin. (Certain installations may require professional
help.) Also be sure your installation conforms to local codes.
!
CAUTION: PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE!
NOTE: For proper operation the recommended working pressure is between 25 psi at valve when flushing and 80 psi static.
RECOMMENDED TOOLS AND MATERIALS
Putty Knife Regular Screwdriver
Hacksaw Wax Ring/Gasket
Closet Flange Set (Cadet Toilets)
1 REMOVE OLD TOILET
a. Close toilet supply valve and flush tank completely. Towel or sponge remaining water from tank and bowl.
b. Disconnect and remove supply line. NOTE: If replacing valve, first shut off main water supply!
c. Remove old mounting hardware, remove toilet and plug floor waste opening to prevent escaping sewer gases.
d. Remove closet bolts from flange and clean away old wax, putty, etc. from base area.
NOTE: Mounting surface must be clean and level before new toilet is installed!
FOR CADET TOILETS:
2-1
DIMENSIONS (Nominal) NOTE: Distance from wall to closet
flange centerline (rough-in) must be 12" (305 mm)
30-1/4"
(768mm)
1"
(27mm)
9"
(226mm)
18-1/2"
(470mm)
6" 13-3/4"
(150mm) (347mm)
12"
(305mm)
3-1
INSTALL CLOSET BOLTS
Install closet bolts in flange
channel, turn 90°, and slide
into place 6" (152 mm)
apart and parallel to wall.
CLOSET BOLTS
P r o d u c t n a m e s l i s t e d h e r e i n a r e t r a d e m a r k s o f A S A m e r i c a , I n c .
© A S A m e r i c a , I n c . 2 0 0 9
Adjustable Wrench
Flexible Supply Tube
Neoprene or Graphite Felt Gasket (Yorkville Toilets)
20-1/2"
(516mm)
14"
(356mm)
9-1/2"
(238mm)
CLOSET FLANGE
305mm
(12)
Sealant Tape Measure
Closet Bolts Carpenters Level
FOR YORKVILLE TOILETS:
2-2
DIMENSIONS (Nominal) NOTE: Distance from floor to closet
flange centerline (rough-in) must be 4" (102 mm) with flange
surface flush to 1/16" (16mm) max. beyond finished wall.
29-3/4"
(752mm)
1/2"
(11mm)
9"
(226mm)
18-1/2"
(470mm)
13-5/8" 12"
(346mm) (305mm)
3-2
INSTALL CLOSET BOLTS
Install closet bolts in flange
channel, turn 90°, and slide
into place 6" (152 mm) apart
and parallel to floor. (Use
putty to hold bolts in place if
necessary.) Brace under
flooring as needed and
drill two mounting pilot
holes as shown.
20-1/2"
(516mm)
14"
(356mm)
9"
(230mm)
CLOSET
FLUSH TO
BOLTS
1/16" (16mm)
EXPOSED
CLOSET
FLANGE
102mm
(4)
346mm
(13-5/8)
168mm
PILOT
(6-5/8")
HOLES
7 3 01 3 12 - 10 0