3M Dynapro ET 350 Installation Manual
  1. Manuals
  2. Brands
  3. 3M Manuals
  4. Monitor
  5. Dynapro ET 350 Monitor
  6. Installation manual
3M Dynapro ET 350 Installation Manual

3M Dynapro ET 350 Installation Manual

Hide thumbs Also See for Dynapro ET 350:
Table of Contents

Advertisement

Quick Links

Download this manual
ET 350 Monitor
User's Installation Guide
Read and understand all safety information
before installing and using this product.

Advertisement

Table of Contents
loading

Related Manuals for 3M Dynapro ET 350

Summary of Contents for 3M Dynapro ET 350

  • Page 1 ET 350 Monitor User’s Installation Guide Read and understand all safety information before installing and using this product.
  • Page 2 3M Touch Systems, a subsidiary of 3M, is prohibited. Notice Given the variety of factors that can affect the use and performance of a 3M Touch Systems Product, including that solid state equipment has operation characteristics different from electromechanical equipment, some of which factors are uniquely within User’s knowledge and control, it is essential that User...

  • Page 3: Intended Use

    Follow all product and accessory installation instructions. Any servicing or other procedures not described in this manual are to be performed only by 3M Touch Systems service personnel. For the ET 350R monitor in a Pollution Degree 3 environment, install the unit in an enclosure that is sealed to a NEMA 4X/IP66 standard.
  • Page 4 3M Dynapro ET 350 Monitor User’s Installation Guide Warning To reduce the risk of electric shock which could result in serious personal injury or death: Do not open the power supply in the ET 350 monitor. It contains hazardous voltages. The power supply has no user-serviceable parts or adjustments inside.
  • Page 5 Product safety information Warning To reduce the risks associated with electric shock and/or burn- related injury that could result in death or serious injury and/or property damage: Do not open the power supply in the ET unit. It contains hazardous voltage/ hazardous energy.
  • Page 7 Suivez toutes les instructions d’installation du produit et des accessoires. Tout entretien ou autre procédure qui n’est pas décrite dans ce manuel doit être réalisée seulement par le personnel du service de 3M Touch Systems. Pour le moniteur ET 350R dans un environnement à polution de type 3, installez l’unité...
  • Page 8 Guide d’installation pour utilisateur du moniteur ET 350 3M Dynapro Avertissement (suite) Afin de réduire le risque d’électrocution qui peuvent causer des blessures corporelles sérieuses ou mortelles : N’ouvrez pas l’alimentation électrique du moniteur ET 350. Il contient des voltages dangereux. L’alimentation électrique n’a pas de pièces à remplacer par l’utilisateur ou de dispositifs de réglage à...
  • Page 9 Renseignements au sujet de la sécurité du produit Avertissement Pour réduire les risques de décharges électriques ou de brûlures susceptibles, faute de précaution, de causer la mort, des blessures graves et/ou des dommages matériels : Ne pas ouvrir le bloc d’alimentation du terminal ET. Il comporte des tensions dangereuses.
  • Page 11 Volg nauwkeurig de installatie-instructies van dit product en de eventuele accessoires. Alle onderhoudswerkzaamheden die niet beschreven worden in deze handleiding, moeten uitsluitend worden uitgevoerd door 3M Touch Systems onderhoudspersoneel. Voor de installatie van de ET 350R monitor in een omgeving met vervuilingsgraad 3: plaats de eenheid in een afgesloten gedeelte conform de NEMA 4X/IP66 standaard.
  • Page 12 3M Dynapro ET 350 Monitor Gebruikershandleiding voor Installatie Waarschuwing (vervolg) Om het gevaar van ernstig of dodelijk persoonlijk letsel als gevolg van elektrische schokken te beperken: Maak de vermogensvoeding van de ET 350 monitor niet open. Deze bevat een gevaarlijk voltage. De vermogensvoeding bevat geen onderdelen die aanpassing of onderhoud vergen door gebruikers.
  • Page 13 Informatie productveiligheid Waarschuwing Neem het volgende in acht om de risico's van elektrische schokken en/of brandwonden te reduceren die ernstig letsel, de dood en/of schade aan eigendommen tot gevolg kunnen hebben: Maak de voedingsbron in de ET-eenheid niet open. Hierin is een gevaarlijke spanning/gevaarlijke energie aanwezig.
  • Page 15 Bundes- und Landesbaubestimmungen zu entsprechen. Beim Ersetzen von Sicherungen oder anderen Teilen sind grundsätzlich nur Teile einzusetzen, die dem von 3M Touch Systems angegebenen Typ und Nennwert entsprechen. Installieren Sie den Monitor ET 350R so, dass er den Umweltversiegelungs- bestimmungen der Norm NEMA 4X/IP66 entspricht.
  • Page 16 Monitor 3M Dynapro ET 350 Montageanleitung Warnhinweise (Forts.) Maßnahmen zum Schutz vor elektrischem Schlag, der zu schwerer Körperverletzung oder Tod führen kann: Die Netzteil des Monitors ET 350 nicht öffnen, da es unter gefährlicher Spannung steht. Das Netzteil enthält keine Teile oder Einstellungs- möglichkeiten, die von Benutzern gewartet werden können.
  • Page 17 Produktsicherheitshinweise Warnhinweise Maßnahmen zum Schutz vor Elektroschock- bzw. Verbrennungsrisiken, die zu schweren Unfällen mit Todes- oder Verletzungsfolge bzw. Sachschäden führen können: Das Netzteil des ET-Monitors nicht öffnen, da es unter gefährlicher Stromspannung steht. Das Netzteil enthält keine Teile oder Einstellungsmöglichkeiten, die vom Benutzer gewartet werden können. Die Verbindungen auf der Klemmleiste nur berühren, wenn die Stromzufuhr unterbrochen ist.

  • Page 19: Informazioni Per La Sicurezza

    Seguire tutte le istruzioni per l'installazione del prodotto e dei suoi accessori. Per operazioni di manutenzione o altre procedure non descritte in questo manuale, rivolgersi solo a personale di assistenza 3M Touch Systems. Per il monitor ET 350R in ambiente di inquinamento Classe 3, installare l'unità...
  • Page 20 Guida per l’installazione del Monitor 3M Dynapro ET 350 Avvertenza (segue...) Precauzioni per ridurre il rischio di scosse elettriche che potrebbero causare lesioni gravi o fatali: Non aprire l'alimentatore del monitor ET 350. Esso contiene parti sotto tensione elevata. L'alimentatore non contiene parti che richiedono manutenzione o regolazione da parte degli utenti.
  • Page 21 Informazioni per la sicurezza Attenzione Per limitare o prevenire il rischio di scosse elettriche e/o di ustioni che potrebbero provocare incidenti gravi o mortali e/o danni alle attrezzature, attenersi alle istruzioni riportate di seguito: Non aprire l'alimentatore del monitor ET, poiché contiene componenti con una tensione e una potenza pericolose.
  • Page 23 Siga todas las instrucciones de instalación del producto y sus accesorios. Todo procedimiento de mantenimiento no descripto en este manual deberá ser realizado, exclusivamente, por el personal de mantenimiento de 3M Touch Systems. Con respecto al monitor ET 350R a ubicar en un ambiente con una contaminación grado 3, instale la unidad en un gabinete aprobado según el...
  • Page 24 Monitor 3M Dynapro ET 350 - Guía de Instalación del Usuario Advertencia (continuación) Para reducir el riesgo de choque eléctrico que podría resultar en lesiones personales severas o muerte: No abra la fuente de alimentación del monitor ET 350. Contiene tensiones peligrosas.
  • Page 25 Información de seguridad del producto Advertencia Para disminuir los riesgos relacionados con descargas eléctricas y quemaduras, los cuales, si no se evitan, pueden ocasionar la muerte, lesiones graves o daño a la propiedad: • No abra la unidad de suministro de energía de la unidad ET, pues contiene energía o voltaje peligroso.
  • Page 27      3M Dynapro ET 350 ET350R ET 350L2 ET350L3 ET350 ET350 3M Touch Systems (Pollution Degree) ET 350R NEMA 4X/IP66 ET 350 ET 350 ET 350L3 ET 350R 3M Touch Systems NEMA4X/ IP66 ET 350R NEMA 4X/IP66...
  • Page 28  3M Dynapro ET 350     ET 350 ET 350 ET 350 Windows  Windows  1 Windows (DPMS) Utility 減小電擊和/或灼傷危險，否則可能造成死亡或嚴重傷害和/或財產損： •切勿打開ET裝置中的電源。其中帶有危險性電壓/危險性能量。電源內 部沒有使用者可維修的零部件或調節。 • 避免接觸電源端子帶上的連接器，除非已斷開電源。 • 避免接觸ET裝置內部的裸露電氣部件。 減小電擊或失火危險，若不加以防範，會造成死亡或嚴重傷害和/或財 產損失： •果是使用NEMA 4X面板襯墊安裝ET裝置，則在列出的(UL)殼罩內安裝 該裝置。 減小機械功能危險，若不加以防範，可能導致財產損失： • 切勿在操作規範之外的條件下操作ET裝置。 減小失火和爆炸的危險，若不加以防範，可能造成死亡或嚴重傷害和/ 或財產損失：...
  • Page 29     ET 350   xxvii...

  • Page 31: Table Of Contents

    Topics ......................1 Warnings and cautions ................1 Related documents ..................1 Terms......................2 Product support ..................3 Contacting 3M Touch Systems ..............3 Chapter 1 Introducing the ET 350 monitor........5 Packing lists....................5 Standard features ..................6 Distinctive features of each model ............8 Options ....................
  • Page 33 List of Figures Figure 1: 3M Dynapro ET 350 monitor ........... 6 Figure 2: NEMA 4X panel gasket (comes with ET 350R) ...... 8 Figure 3: NEMA 4X hatch and extended cover (comes with ET 350L3) 9 Figure 4: Moisture Deflector option............11 Figure 5: Connectors: ET 350 monitor (without KVM extender) ..

  • Page 35: Before You Start About The User's Installation Guide

    If you ordered either the ET350R monitor or the ET 350L3 monitor, one of these installation instruction documents will ship with this manual and your monitor (and are also available for download from the 3M Touch Systems web site: www.3Mtouch.com):...

  • Page 36: Terms

    For DPMS instructions for ET 35X monitor models with a heater, refer to instructions that ship with models with heaters. Graphic underlay A graphic that illustrates the TouchSurround and fits behind the touch screen. 3M (also called TouchSurround Dynapro industrial products may be ordered with standard or custom underlays.

  • Page 37: Product Support

    Before you start: About the User’s Installation Guide Product support Registration Register your 3M Dynapro ET 350 monitor by mailing the postage-paid Product Registration Card. It detaches from the Warranty Card that came with your unit. The Product Registration Card may also be faxed to 3M Touch Systems (604-521-4629).

  • Page 39: Chapter 1 Introducing The Et 350 Monitor

    Allen key (5/32-inch). Full-scale cutout template. Warranty card with detachable mail-in Product Registration Card. 3M Dynapro ET 350 Monitor User’s Installation Guide (this manual). Model-specific packing lists In addition to the standard items listed above, each of the three ET 350 monitor models will come with different materials (for information on the distinctive features of each model, see “Distinctive features of each...

  • Page 40: Standard Features

    3M Dynapro ET 350 Monitor User’s Installation Guide ET 350L3 monitor (hatch) NEMA 4X hatch and extended hatch cover NEMA 4X hatch gasket Cable fitting components Screws Clear, flexible insulator Instructions for installing the NEMA 4X hatch The packing list for the KVM extender option appears on page 10.
  • Page 41 For details, see “Backlights saver” on page 25. For information on replacing the backlights, contact 3M Touch Systems customer service (see “Contacting 3M Touch Systems” on page 3).

  • Page 42: Distinctive Features Of Each Model

    3M Dynapro ET 350 Monitor User’s Installation Guide Distinctive features All ET 350 monitor units have the standard features described above. The of each model distinctive features of each model are described below and summarized in Table A. ET 350R monitor (NEMA 4X panel gasket) The ET 350R monitor has a UL Recognized component mark.

  • Page 43: Figure 3: Nema 4X Hatch And Extended Cover (Comes With Et 350L3)

    Installation instructions (No on-site inspection required). Note: IEC and stripped power cables are available from 3M Touch Systems for both North American and European applications. For more information on power cables, see “Step 3: Connect to power supply” in Chapter 2, page 16...

  • Page 44: Options

    3M Dynapro ET 350 Monitor User’s Installation Guide Options There are three types of options that may be ordered for the ET 350 monitor (not including mounting options, which are discussed on page 11): Keyboard, video, and mouse (KVM) extender (single or dual) option...

  • Page 45: Mounting Kits

    ET 350L3 monitor comes with a NEMA 4X hatch The ET 350L2 monitor does not come with mounting/sealing materials. There are three optional mounting kits available from 3M Touch Systems for use with the ET 350 monitor. Each kit comes with its own set of...
  • Page 46 3M Dynapro ET 350 Monitor User’s Installation Guide Table C summarizes the mounting possibilities for each of the ET 350 monitor models. Table C: Mounting possibilities for ET 350 monitor models Monitor NEMA NEMA Desktop Rack Boom Model hatch panel...

  • Page 47: Chapter 2 Installing The Monitor

    For permanently connected equipment, a readily accessible disconnect device must be incorporated in the fixed wiring. • Any servicing or other procedures not described in this manual are to be performed only by 3M Touch Systems service personnel.

  • Page 48: Before Installing

    You may choose to use a standard signal cable or make a cable using the “Video signal cable connector” pin-out in Appendix C. When making a cable, 3M Touch Systems recommends you use a high-quality shielded cable such as Belden cables 1417B, 1418B, 1522A, or 1826A.

  • Page 49: Step 2: Connect Serial Cable

    Chapter 2: Installing the monitor Important • To reduce the risk of voiding FCC and CE compliance and reducing the performance of the ET 350 monitor, when making your own cable, reduce the sensitivity of the ET 350 monitor to electrical and radio frequency noise by connecting the cable shield to the connector shield (360º...

  • Page 50: Step 3: Connect To Power Supply

    50 to 60 Hz, supplies the appropriate power without requiring any adjustment. For North American applications, use a standard AC power cable. Both types of cable are available from 3M Touch Systems and come with either an IEC connector or terminal strip wiring. Warning...

  • Page 51: Figure 6: Connecting Ac Power Cable Wires To Connectors

    Chapter 2: Installing the monitor To connect the AC power cable: 1. If the monitor has a hatch , make sure that the hatch is open (it should have been opened when connecting the video cable). The hatch must be open to access connectors. Connect the power cable to the socket on the side of the monitor.

  • Page 52: Figure 7: Terminal Connection For Ac Power (Et 350R, Et 350L3 Monitors) And For Dc Power

    3M Dynapro ET 350 Monitor User’s Installation Guide Using a 1/8-inch flathead screwdriver, turn the terminal block’s screw clockwise until the neutral cable wire is firmly attached to the ET 350 monitor. Repeat (5) and (6) for the ground and line cable wires and then tighten the screws on the terminal block to a torque of 10 inch- pounds.

  • Page 53: Step 4: Adjust Display Settings

    Chapter 2: Installing the monitor Figure 8: Connecting DC power cable wires to connectors Using a 1/8-inch flathead screwdriver, turn the screw on the terminal strip clockwise until the negative cable wire is firmly attached. Repeat steps (5) and (6) for the “ground” and DC+ cable wires and then tighten screws on the terminal block to a torque of 10 inch- pounds.

  • Page 54: Figure 9: Pc Menu Options

    3M Dynapro ET 350 Monitor User’s Installation Guide Table D: Summary of on-screen display controls Symbol Name Function of the control Display controls inside ET 350 monitor enclosure Menu To start up the on-screen display menus and to move through the menu options.

  • Page 55: Figure 10: Auto Display Setup

    Chapter 2: Installing the monitor Figure 10: Auto display setup Press once. The display settings are automatically optimized. Manually adjusting display settings If the auto display setup settings are not suitable for your application, you can make manual adjustments to the display settings. Follow these steps: Press once.

  • Page 56: Step 5: Install Software And Import Touchsurround Files

    3M Dynapro ET 350 Monitor User’s Installation Guide Other on-screen display options The most commonly used on-screen display options are those that appear under the PC and Auto icons. Other on-screen options that can be set using the controls are summarized below.
  • Page 57 Chapter 2: Installing the monitor Follow the screen prompts to install the driver and then follow the on- screen instructions of the Setup Wizard. : When the Baseline dialog box appears, select Skip. When the Note Linearization Data Download dialog box appears, select Skip. Baseline and linearization data are built into the monitor at the factory.
  • Page 58 3M Dynapro ET 350 Monitor User’s Installation Guide Click Yes in reply to the question: Are you sure you want to use this driver? The Update Device Driver Wizard appears. Insert your CD-ROM for the Windows 98 operating system. (If the CD-ROM welcome page appears, close it so you can see the Wizard dialog box.)

  • Page 59: Step 6: Set "Backlights Saver" And "Safe Touch

    Chapter 2: Installing the monitor To import the standard TouchSurround definition for Windows NT 4.0 and Windows 9X operating systems, follow these steps: Select the Windows Start button, select Programs, and then select Command Prompt. At the command prompt, type CD\TOUCH\NT for Windows NT CD\TOUCH\W9X for Windows 9X Type TOUCHINI /i350.ini...
  • Page 60 3M Dynapro ET 350 Monitor User’s Installation Guide If the ET 350 monitor is running an application or is in a setting in which unintentionally activating a button on the touch screen might have harmful consequences for people or equipment, 3M Touch Systems recommends creating a “safe touch”...
  • Page 61 Chapter 2: Installing the monitor Select OK. If your ET unit has a display power management system (DPMS), that is configurable from the display’s on-screen menu options, make sure that it is turned on. For details on how to check DPMS, see “Utility menu”...

  • Page 62: Step 7: Close Enclosure And Hatch

    ET 350L3 monitor with a NEMA 4X hatch The ET 350L2 monitor does not come with mounting materials, but there are optional mounting kits available from 3M Touch Systems (see below). For details of the features of the three ET 350 monitor models, see “Distinctive features of each model”...
  • Page 63 Mounting the ET 350 monitor with Moisture Deflector The ET 350 monitor with Moisture Deflector comes with four sealing screws fastened to the back of the unit. 3M Touch Systems recommends that if you need to remove the sealing screws to access the enclosure, you re-attach the screws after closing the enclosure.

  • Page 65: Chapter 3 Maintaining The Monitor

    CHAPTER 3 Maintaining the monitor About the chapter This chapter describes how to: Clean the touch screen and enclosure Replace backlights Replace the fuse Check gaskets for damage or improper functioning Maintain the ET 350 monitor with Moisture Deflector Warning To reduce the risk of electric shock which could result in serious personal injury or death, do not open the power supply in the ET 350 monitor.

  • Page 66: Replacing Backlights

    3M Dynapro ET 350 Monitor User’s Installation Guide Cleaning the enclosure Use a 50 percent solution of alcohol (ethanol or isopropanol) in water on a cotton gauze pad or soft cotton cloth to clean the enclosure. Be sure to apply the alcohol solution to the cloth only, not directly to the enclosure.

  • Page 67: Checking Gaskets

    Follow these guidelines to check and clean the gaskets on your monitor: Make sure there is no debris on gaskets that will prevent a seal. If debris needs to be cleaned from gaskets, do so gently. If gaskets are torn or damaged, return to 3M Touch Systems for servicing.

  • Page 68: Maintaining The Et 350 Monitor With Moisture Deflector

    Maintaining the ET The Moisture Deflector is made of durable plastic and, like other 350 monitor with 3M Dynapro components, is designed to function in rugged conditions. Moisture Deflector It is not indestructible, however. Follow these guidelines to extend its life...

  • Page 69: Chapter 4 Touchsurround And Graphic Underlay

    Standard TouchSurrounds Standard TouchSurround layouts from 3M Touch Systems feature predefined buttons that permit some keyboard functions (for example, Enter) to be performed by touch. The functions of the buttons can be changed by following instructions in the software guide appropriate for your operating system (see “Software guides”...
  • Page 70 3M Dynapro ET 350 Monitor User’s Installation Guide Creating your own graphic underlay If you need a custom graphic underlay, it is recommended that you order it from 3M Touch Systems, especially if the underlay will need to withstand temperature and humidity extremes. Important...

  • Page 71: Replacing A Touchsurround Graphic Underlay

    Chapter 4: TouchSurround and graphic underlay Replacing a What you will need TouchSurround The rest of this chapter describes how to remove the graphic underlay that graphic underlay came with your monitor and replace it with a new, custom underlay. To do the tasks described in this section, you will need: A clean, ESD-protected environment with a work bench.

  • Page 72: Figure 13: Location Of Optional Security Screws

    3M Dynapro ET 350 Monitor User’s Installation Guide Put on an ESD grounding wrist strap if one is available. If a grounding wrist strap is not available, touch a grounded metal object to discharge any static charge from your body.

  • Page 73: Figure 14: Disconnecting Touch Screen Tail Connector

    Chapter 4: TouchSurround and graphic underlay Carefully disconnect the touch screen tail connector from the controller board (Figure 14). Gently pull out the touch screen connector’s retaining clip with two fingers. Gently pull the touch screen tail from the controller and through the ferrite block.

  • Page 74: Figure 15: Removing Display Panel Nuts And Washers

    3M Dynapro ET 350 Monitor User’s Installation Guide Using a 5/16-inch torque hex nut drive, remove the four display panel nuts and washers (Figure 15). Figure 15: Removing display panel nuts and washers...

  • Page 75: Figure 16: Sliding Display Pan Out And Lifting It

    Chapter 4: TouchSurround and graphic underlay Carefully slide the display pan away from the threaded studs and lift it to a vertical position, taking care not to damage the cables connected to the components on the display pan (Figure 16): Lift the hinge side of the display pan up from the threaded studs.

  • Page 76: Figure 17: Removing Original Underlay

    3M Dynapro ET 350 Monitor User’s Installation Guide Remove the underlay in stages. The underlay is larger than the opening in the sheet metal retaining frame. You can bend the underlay, but do not tear or crease it. To loosen the underlay from the glass surface, use a finger and push a corner of the underlay towards the center of the glass.

  • Page 77: Figure 18: Placing New Underlay

    Chapter 4: TouchSurround and graphic underlay Being careful not to damage the new underlay, place it under the retaining frame in stages: slide one corner in place under the retaining frame, then bend the underlay and slide in the next corner. Continue until the underlay is in place against the surface of the glass (Figure 18).

  • Page 78: Figure 19: Reconnecting Touch Screen Tail

    3M Dynapro ET 350 Monitor User’s Installation Guide Gently reconnect the touch screen tail to the controller (Figure 19): Pull out the touch screen connector’s retaining clip. Slide the touch screen tail through ferrite and insert it into the connector.

  • Page 79: Chapter 5 Troubleshooting

    About the chapter This chapter outlines problems that may occur when using the 3M Dynapro ET 350 monitor and suggests solution strategies. If problems persist after following the applicable instructions in this chapter, contact 3M Touch Systems technical support (see page 3).
  • Page 80 3M Dynapro ET 350 Monitor User’s Installation Guide Problem Solution ET 350 monitor does not power Try the following: up when plugged in. Make sure that the power to the monitor’s power cable is turned on. Make sure that the power to the host computer’s power supply is turned on.

  • Page 81: Touch Screen Driver Error Messages

    If you see one of the following error messages, messages please note the number displayed with it. This will help 3M Touch Systems technical support staff to diagnose the problem (see page 3). Error message...

  • Page 83: Appendix A Specifications

    APPENDIX A Specifications Enclosure and cutout dimensions Imperial Metric Enclosure 14.00" high 16.30" wide 355.60 mm high 414.02 mm wide 6.32" deep 160.53 mm deep Panel cutout 313.18 mm high 12.33" high 14.36" wide 364.74 mm wide Mounting Rear 1" Rear 25.4 mm clearances Weight...

  • Page 84: Figure 21: Cutout Dimensions

    3M Dynapro ET 350 Monitor User’s Installation Guide 6.685" (169.80 mm) 30023_a Figure 21: Cutout dimensions...

  • Page 85: Display Specifications

    94.500 Chemical The bezel provides resistance to user abuse and to most chemicals and resistance other substances. Contact 3M Touch Systems technical support for guidelines on protecting the equipment from specific chemicals. Supported Windows XP Professional operating system operating systems Windows 2000 Professional operating system Windows NT 4.0 operating system...

  • Page 86: Ac Power Supply

    3M Dynapro ET 350 Monitor User’s Installation Guide Communications Port/ Description connector Touch screen interface to host Standard Serial computer monitor RS-232C compatible asynchronous serial port 9-pin female D-connector Video interface to host VGA signal cable port 15-pin female VGA connector Analog RGB 0.7V p-p...

  • Page 87: Operating Conditions

    Appendix A: Specifications Operating conditions Condition Range Operating 0°C to 50°C (32°F to 122°F) temperature Humidity 50°C, 5% to 95% non-condensing Maximum operating 6,560 feet (2,000 meters) altitude Vibration 5 to 57 Hz 0.006 in peak displacement 58 to 2000 Hz 1.0 G acceleration Shock Acceleration: 15 G Pulse duration: 11 ms...
  • Page 88 3M Dynapro ET 350 Monitor User’s Installation Guide FCC compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide a reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 89: System Software

    Appendix A: Specifications Electromagnetic emission standards EN55022 Class A ICES-003 Class A FCC CFR 47, Part 15, Subpart B, Class A C-Tick — Australia, New Zealand Product certifications UL Information Technology Equipment — United States ET 350R monitor (with panel gasket) UL recognized component for Pollution Degree 3 environments if installed and tested with panel gasket in an enclosure that meets NEMA 4X/IP66 rating.

  • Page 91: Appendix B Installing Monitor With Kvm Extender

    APPENDIX B Installing monitor with KVM extender About this This appendix provides instructions for installing the ET 350 monitor with appendix the keyboard, video, and mouse (KVM) extender option. For more information about the KVM extender, refer to the manufacturer’s manual that came with your ET 350 monitor.
  • Page 92 3M Dynapro ET 350 Monitor User’s Installation Guide These jumpers (JP3, JP4, and JP5) can be set to adjust equalization of the monitor’s display to compensate for loss of image quality due to the signal passing through a long cable.
  • Page 93 Appendix B: Installing monitor with KVM extender If the length of cable between the local and remote units is near the high end of one of the ranges and you are using high-resolution video (1024 x 768), try setting jumpers for the next higher cable length. This might help improve video compensation.
  • Page 94 3M Dynapro ET 350 Monitor User’s Installation Guide Remove the bracket, find the DIP-Switch on the board, and move the switch to the on position. Replace the bracket and screws and close the enclosure. Step 2: To connect communications cables, follow these steps: Make connections 1.

  • Page 95: Figure 23: Connectors: Et 350 Monitor With Kvm Extender

    Appendix B: Installing monitor with KVM extender Figure 23: Connectors: ET 350 monitor with KVM extender Remaining steps Continue the installation steps in Chapter 2, beginning with Step 3 on page 16: “Step 3: Connect to power supply “Step 4: Adjust display settings “Step 5: Install software and import TouchSurround files “Step 6: Set ‘backlights saver’...

  • Page 97: Appendix C Connector Pin-Outs

    APPENDIX C Connector pin-outs Video signal cable connector Signal Red video Green video Blue video N.C.* Vertical sync. return Red return Green return Blue return N.C.* Horizontal sync. return N.C.* N.C.* Horizontal sync. Vertical sync. N.C.* Important: To reduce the risk of voiding FCC and CE compliance and reducing the performance of the ET 350 monitor, when making your own cable, reduce the sensitivity of the ET 350 monitor to electrical and radio frequency noise by connecting the cable shield to the connector shield (360 degree shield) on both...
  • Page 98 3M Dynapro ET 350 Monitor User’s Installation Guide Serial port RS-232C connector Signal Description In/Out N.C.* Receive Data Transmit Data Data Terminal Ready SGND Signal Ground N.C.* N.C.* N.C.* N.C.* Important: To reduce the risk of voiding FCC and CE compliance and reducing...
  • Page 99 Appendix C: Connector pin-outs CAT 5 interconnecting Color Function, pair cable (for KVM White/Orange TX, Pair 2 extender) Orange/White RX, Pair 2 White/Green TX, Pair 3 Blue/White RX, Pair 1 White/Blue TX, Pair 1 Green/White RX, Pair 3 White/Brown TX, Pair 4 Brown/White RX, Pair 4 *Looking into the interconnect socket on either the remote or local unit, or...
  • Page 100 3M Dynapro ET 350 Monitor User’s Installation Guide Keyboard and mouse (for KVM Signal extender) Data N.C.* Clock N.C.* Important: To reduce the risk of voiding FCC and CE compliance and reducing the performance of the ET 350 monitor, when making your own cable, reduce...
  • Page 101 Index extender) serial cable video cable AC power supply fixed field wiring Connector pin-outs specifications see Pin-outs standard wiring Controls for on-screen display ACPI settings defined Customer support Cutout dimensions Backlights replacing DC power supply (option) safe touch setting connecting setting saver specifications specifications...
  • Page 102 Moisture Deflector – mounting – mounting kit options Keyboard & mouse cable (KVM packing lists extender) registering connecting returning to 3M Touch Systems pin-outs safety labels Keyboard & mouse control safety standards setting DIP-Switch SW1 (KVM – specifications extender) –...
  • Page 103 – fuse – graphic underlay Near Field Imaging (NFI). see Resistance to chemicals MicroTouch Near Field Imaging Returning ET 350 monitor to 3M Touch Non-operating conditions Systems On-screen display settings Safe touch setting adjusting described auto display setup Windows 9X operating system...
  • Page 104 Terms Video cable connecting 3M Touch Systems pin-outs customer support returns policy Video drivers, downloading latest trademarks Touch screen cleaning defined Windows 9X operating system TouchSurround backlights saver defined Windows NT/9X operating systems importing definition files – installing driver replacing underlay Windows XP/2000 operating systems TouchSurround.

This manual is also suitable for:

Dynapro et 350rDynapro et 350l2Dynapro et 350l3

Table of Contents