Advertisement
LOCATION
OF THE PORTABLE AiR CONDiTiONER
/
/
1. Select
a location
near
a window
and
electrical
outlet.
2.
Position
the unit
in a fiat,
spacious
location
with
a minimum
of one foot
of clearance
(30
cm) between
the air outlets
and
any
wall
or pieces
of furniture.
3. If
placing
the unit
outside
of the room
to be
cooled,
position
it on a fiat
solid
surface,
preferably
in a space
with
overhead
shielding
from
rain and
the direct
rays
of the sun. Do not operate
the unit
in
extremely
moist
areas
such as a sauna.
WINDOW
KIT INSTALLATION
The Window
Kit (included)
contains three sliding pieces, and can be adjusted
to fit most standard
vertical
and horizontal
windows
(see Figs. 1 & la). For
very wide windows,
use all three pieces. For very narrow windows,
you may
have to cut down the end of the piece with the hose attachment
hole. Do not
cut into the hole.
EXHAUST HOSE CONNECTION
The exhaust hose must be attached
to the appropriate
side of the unit given
the desired
application,
either cooling
or heating
(see Operating
Instructions).
When changing
applications,
switch the adjustable
air vent and exhaust hose
holder (hose can remain attached)
to the opposite
sides of the unit.
zii
Window
kit
Min: 19 in.
(48 cm)
Max: 50 in.
(127 cm)
Vertical
Window
Window
kit
Min: 19 in.
(48 cm)
Max:
50 in.
(127 cm)
Horizontal
Window
10
This product
is equipped
with an LCDI (Leakage
Current Detection
and
Interruption)
safety
plug. If power shuts off:, unplug
from the electrical
outlet
and make sure the cord is undamaged.
If the cord is damaged,
return the unit
to a Sears Service Center for repair
before using it again.
TO TEST THE SAFETY PLUG
1. Connect the power plug to an electrical
outlet.
2. The power plug has two buttons located
on the top. One button is marked
"TEST" and the other is marked "RESET'L Press the "TEST" button;
you wiii
hear a click as the "RESET" button pops out.
3. Press the "RESET" button;
you wiii hear a click as the button engages.
4. The power supply cord is now energized
and supplying
electricity
to the
air conditioner
(it is indicated
by a light on the plug head).
°
Under no circumstances
should this device
be used to turn the unit on
or
off:.
°
The "RESET" button
must always
be pushed in (engaged)
for correct
operation.
°
The power supply cord must be replaced
if it fails to reset when the
"TEST" button
is pushed in.
(5)
(2) --
(7) --
(i) --
o
[_
(3)
--
(6)
--
(8)
(4)
1. POWER (_
Press this button
to switch
the unit on or off:.
2. MODE
Press this button
to select
between
Cooling
(_),
Heating (_)
or Dehumidifying (iitj) mode.
NOTE: To change
display
between
°F
and °C, press the MODE
button for 10
seconds with the power off: and unit
plugged
in (Standby
Mode).
You will
hear a beep when the change
occurs.
3. TEMP+
A
•
Pressing this button in cooling
mode increases the desired room
temperature
setting by I°F (1°C) up to
a maximum setting of 86°F (30°C).
•
Pressing this button in heating
mode increases the desired room
temperature
setting by I°F (1°C) up to
a maximum setting of 77°F (25°C).
11
Advertisement
