GE JGP328 Installation Instructions Manual

30" sealed gas cooktops
Hide thumbs Also See for JGP328:

Advertisement

Available languages

Available languages

I Iinstallation
130"
Sealed Gas Cooktop
nstructions
JGP940,
JGP94s
=_
Questions?
Call 800.GE.CARES
(800.432.2737)
or Visit our Website
at: go.corn
In Canada,
call 1.800.361.3400
or Visit our Website
at: www.geappliances.ca
I
IN THE COMMONWEALTH
OF
MASSACHUSETTS:
• This product
must be installed
by a
licensed
plumber
or gas fitter.
• When
using ball-type
gas shut-off
valves,
they shall be the T-handle
type.
• A flexible
gas connector,
when
used, must
not exceed 3 feet.
BEFORE YOU BEGIN
Read these
instructions
completely
and carefully.
• iMPORTANT - Save t hese
instructions
for local inspector's
use.
• iMPORTANT
- Observe all
governing
codes
and ordinances.
Note to Installer
- Be sure to leave these
instructions
with
the Consumer.
Note to Consumer
- Keep these
instructions
for future
reference.
Product
failure
due to improper
installation
is not covered
under
the Warranty.
-&WARNING
-
This appliance
must
be properly
grounded.
IMPORTANT
-
Leak testing
of the
appliance
shall
be conducted
according
to
the manufacturer's
instructions.
= Proper installation
is the responsibility
of the installer
and product
failure
due to
improper
installation
is NOT covered
under
warranty.
-&WARNING - Disconnect
all
electrical
power
at the main circuit
breaker
or fuse box before
installing.
FOR YOUR SAFETY:
-&WARNING - Iftheinformation
in this manual
is not followed
exactly,
a fire,
explosion
or gas leak may result causing
property
damage,
personal
injury or death.
Do not store or use gasoline
or other
flammable
vapors
and liquids in the vicinity
of this or any other
appliance!
WHAT TO DO IF YOU
SMELL GAS:
Do not try to light
any appliance.
Do not
touch
any electrical
switch;
do not use any
phone
in your
building.
Immediately
call your
gas supplier
from
a
neighbor's
phone.
Follow
the gas supplier's
instructions.
• If you cannot
reach your
gas supplier,
call
the fire department.
Installation
and service
must
be performed
by a qualified
installer,
service
agency
or
the gas supplier.
This cooktop
has been design
certified
by CSA International.
You'll
find safety
precautions
in your
Owner's
Manual,
Read them
carefully.
• Installation
of this cooktop
must
conform
with
local codes
or in the absence
of local
codes
with
the National
Fuel Gas Code,
ANSI
Z223,1/NFPA
54-Latest
edition.
Be sure your
cooktop
is installed
properly
by a qualified
installer
or service
technician.
To eliminate
reaching
over surface
burners,
cabinet
storage
above
burner
should
be
avoided.
• Do not install
the unit near an outside
door
or where
a draft
may affect
its use,
31-10613-3
(11-06 JR)
1

Advertisement

Table of Contents
loading

Summary of Contents for GE JGP328

  • Page 1 I Iinstallation 130" nstructions Sealed Gas Cooktop JGP940, JGP94s Questions? In Canada, Call 800.GE.CARES call 1.800.361.3400 or Visit our Website (800.432.2737) or Visit our Website at: www.geappliances.ca at: go.corn IN THE COMMONWEALTH FOR YOUR SAFETY: MASSACHUSETTS: -&WARNING - Iftheinformation • This product...
  • Page 2: Installation Instructions

    Installation instructions IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL REQUIREMENTS PARTS INCLUDED This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse 2 Screws Foam Tape having amperage as noted...
  • Page 3: Pre-Installation

    Installation Instructions PRE-INSTALLATION CHECKLIST When preparing cooktop opening, Remove Installation Instructions from make sure the inside of the cabinet literature pack and read them carefully the cooktop do not interfere with each before you begin. other. (See section on preparing Be sure to place all literature, Use and opening.)
  • Page 4: Preparing The Opening

    Installation Instructions PREPARING THE OPENING MAINTAIN THE FOLLOWING [_] RECOMMENDED GAS SUPPLY MINIMUM CLEARANCE LOCATION FROM BACKWALL DIMENSIONS 1" Min. From Backwall 13" MAX. Depth of unprotected overhead cabinets 6" MIN. clearance from Recommended cutout to side wall on gas supply _,_ 13-1_ / the right of the unit location...
  • Page 5: Installing The Cooktop Unit

    Installation Instructions INSTALLING THE COOKTOP UNIT LOCATE ELECTRICAL OUTLET _-I LOCATE MOUNTING PARTS AND GAS SHUT-OFF VALVE Remove the hold down brackets from BENEATH CABINET literature package. NEVER REUSE OLD CONNECTORS _Shut WHEN INSTALLING THIS UNIT. [ Outlet 12" Valve _[_ Below Countertop I-_ ATTACH BRACKETS TO...
  • Page 6 Installation Instructions INSTALLATION--GAS CONNECTIONS PROVIDE ADEQUATE INSTALL REGULATOR ONTO GAS SUPPLY BURNER BOX BOTTOM This cooktop is designed to operate Screw natural gas at 4" of water column manifold regulator onto pressure and 7" of water column (W.C.) the burner supply pressure.
  • Page 7 Installation instructions CHECK FOR LEAKS INSTALLATION OVER BUILT-IN OVEN Before testing for leaks, make sure all burner knobs are in the OFF position. See built-in oven installation for complete installation instructions. After connecting the cooktop to gas, check system for leaks with a manometer. If a manometer is not available,...
  • Page 8 Installation Instructions INSTALLATION--ELECTRICAL CONNECTIONS -&WARNING - Disconnect _-I ELECTRICAL SUPPLY AND OUTLET electrical power at the main circuit breaker or fuse box before installing. An adequate electrical supply and outlet must be used to operate the electrical parts of your cooktop.
  • Page 9 Installation instructions CAUTION: USAGE SITUATIONS WHERE Attaching the adaptor ground APPLIANCE POWER CORD terminal to the wall receptacle cover screw does not ground the appliance unless the WILL BE DISCONNECTED screw is metal, and not insulated, and the wall INFREQUENTLY receptacle is grounded through...
  • Page 10: Cooktop Burners

    Installation instructions COOKTOP BURNERS Make sure the ASSEMBLING THE COOKTOP Burner cap pins in the burner BURNERS heads match the The electrode of the spark igniter is exposed. burner base Be careful not to push any cooktop controls indentations Burner head while the top of the burner is removed.
  • Page 11 Installation instructions CHECK IGNITERS THE BURNER FLAMES Operation of the electric igniters should Turn each burner on. Flames should be blue checked after the cool{top and supply line in color with no trace of yellow. The burner have been carefully checked for leaks and flames...
  • Page 12: Installation

    Installation Instructions OPERATION CHECKLIST Make sure all controls are left in the OFF When ordering parts, always include position, Check to be sure the cooktop serial number, model number and a code in the UNLOCKED position (on models letter to ensure proper replacement parts.
  • Page 13: Making The Lp Conversion

    Installation instructions MAKING THE LP CONVERSION ADJUST YOUR COOKTOP FOR _-_ SAFETY INFORMATION SHOULD KNOW USE WITH LP GAS The pressure regulator and burner orifices Disconnect all electrical power, at the main circuit breaker or fuse box. are set for natural gas.
  • Page 14 Installation Instructions MAKING THE LP CONVERSION (CONT.) CHANGE COOKTOP BURNER CHANGE COOKTOP BURNER ORIFICES ORIFICES (CONT.) NOTE: On most burners, Remove the top grates, burner caps, the orifices have a spring- Retainer and burner heads. loaded retaining ring Ring Remove This around the hex head to...
  • Page 15 Left Front RightFront These marks denote the precise location Model Orifice Orifice Orifice each orifice to the cooktop burner. JGP328 OOOO JGP330 JGP933 JGP940 18,000 BTU/HR Burner (on some models) JGP945 Replace: With: Main 206XN --) I08XL Simmer --). 34L with markings located in the sides only.
  • Page 16 Installation instructions MAKING THE LP CONVERSION (CONT.) ADJUST BURNER FLAMES Make the adjustment by slowly turning the screw until flame appearance Turn all burners full on and check correct. flames. They should be blue in color with Testing Flame Stability: some yellow tipping...
  • Page 17: Instructions D'installation

    Instructions Table de cuisson scellee d'installation au gaz de 76 cm (30") JGP328, JGP330, JGP933, JGP940, JGP945 Web a I'adresse : www, electromenagersge,ca Questions? Appelez le Centre de reponse 1.800.361.3400 ou visitez notre site AVANT DE COMMENCER POUR VOTRE SECURITE...
  • Page 18 instructions d'instaliation INSTRUCTIONS IMPORTANTES DE SI CURITI PII CES COMPRISES La conception de votre table de cuisson a ete approuve par I'ACNOR International. Vous trouverez des precautions a prendre matiere de securite dans votre Guide d'utilisation et de soins. Lisez-les attentivement.
  • Page 19 Instructions d'instaliation LISTE DE VITRIFICATION AVANT INSTALLATION Enlevez les instructions d'installation Pour preparer I'ouverture de la surface de la trousse de documentation de cuisson, vous devez vous assurer que I'interieur de I'armoire ne touche lisez-les soigneusement avant commencer. pas la table de cuisson (consultez section...
  • Page 20 instructions d'installation PRI PARATION DE L'OUVERTURE vous DEVEZ RESPECTER LES EMPLACEMENT DEGAGEMENTS MINIMAUX RECOMMANDE SUlVANT UALIMENTATION DE G.AZ A PARTIR DU MUR ARRIERE Profondeur max de 33 cm (13") des armoires en surplomb non protegees Degagement rain. de 2.5 cm (1") min. du mur arri_re 15 crn (6") decoupage au tour de c6te ,_ m ,ace ent...
  • Page 21: De La Table De Cuisson

    Instructions d'instaliation INSTALLATION LA UNITI DE LA TABLE DE CUISSON _-I TROUVEZ LES PIECES DE _-I PLACEZ LA PRISE D'ALIMENTATION MONTAGE I_LECTRIQUE ET LE ROBINET Retirez les supports de fixation de la trousse de documentation. D'ALIMENTATION DE GAZ AU-DESSOUS DE L'ARMOIRE DEsN'UTIUSEZRAcCORDsJAMAIS iJ,, Robinet...
  • Page 22 instructions d'instaliation INSTALLATION--BRANCHEMENT DU GAZ INSTALLEZ LE RI_GULATEUR _-I FOURNISSEZ UN BON APPROVISIONNEMENT EN BAS DE LA BOiTE DE EN GAZ BRULEURS Cette table de cuisson est congue pour Vissez fonctionner au gaz naturel a une pression regulateur dans tubulure d'admission de 4 po.
  • Page 23 instructions d'instaliation VI_RIFIEZ QU'IL N'Y A PAS DE [-_ INSTALLATION SUR UN FOUR FUlTE ENCASTRI_ Avant de verifier qu'il n'y a pas de fuite, Consultez I'installation du four encastre pour assurez-vous que tousles boutons y trouver les instructions d'installation. brQleurs soient en position OFF (arrSt).
  • Page 24 instructions d'instaliation INSTALLATION--RACCORDS I LECTRIQUES -&AVERTISSEMENT _-I ALIMENTATION I_LECTRIQUE ET PRISE Debranchez tout courant electrique au niveau du disjoncteur de la maison ou de la boite Vous devez utiliser une bonne alimentation fusibles avant d'installer. electrique et une bonne prise pour faire fonctionner les elements...
  • Page 25 instructions d'instaliation INSTALLATION--RACCORDS I LECTRIQUES (SUITE) MISE EN GARDE "sivousfixez _-I SITUATION D'UTILISATION O0 LE CORDON D'ALIMENTATION D'UN la broche de raise a la terre de I'adaptateur une vis du couvercle de la prise murale, APPAREIL I:!:LECTROMI:!:NAGER cela ne met pas a la terre I'appareil, a moins EST INFREQUEMMENT que la vis soit en metal...
  • Page 26 instructions d'instaliation BROLEURS DE LA TABLE DE CUlSSON N-I ASSEMBLEZ LES BRULEURS Assurez-vous Capuchon de brQleur les broches DE LA TABLE DE CUISSON t_tes de brQleur L'electrode de I'allumeur est exposee. Faites correspondent attention de ne pas pousser un contr61e de la T_te de brQleur aux creux de la...
  • Page 27 instructions d'instaliation VI RIFIEZ LES ALLUMEURS ALLUMAGE DES BRULEURS Vous devez verifier le fonctionnement Allumage de la table de cuisson - Quand allumeurs electriques apres vous _tre vous mettez le bouton de la table de cuisson soigneusement assure que la table de cuisson en position LITE (allumage), rallumeur...
  • Page 28 instructions d'instaliation BRULEURS DE LA TABLE DE CUISSON (SUITE) LES FLAMMES DU BRULEUR GRILLES DE BRULEUR Les quatre grilles de brQleur sont con_ues Allumez chaque brQleur. Les flammes doivent pour leur emplacement particulier. Pour 6tre bleu sans trace de jaune. Les flammes obtenir une stabilite...
  • Page 29 Instructions d'instaliation CONVERSION AU GAZ PROPANE .RENSEIGNEMENTS RELATIFS AJUSTEZ VOTRE PLAQUE A LA SECURITE QUE VOUS CUlSSON A UN USAGE AU DEVEZ CONNAiTRE GAZ PROPANE Les diaphragmes du regulateur de pression et du Debranchez tout le courant electrique, br_leur sont regles pour le gaz naturel. Pour niveau du disjoncteur principal...
  • Page 30 Instructions d'instaliation CONVERSION AU GAZ PROPANE (SUITE) CHANGEZ LES DIAPHRAGMES CHANGEZ LES DIAPHRAGMES DES BRULEURS DE LA TABLE DES BRULEURS DE LA TABLE DE CUlSSON DE CUlSSON (SUITE) Enlevez les grilles NOTE : Sur la plupart haut, les capuchons breleurs, les diaphragmes Baguede de brQleur...
  • Page 31 Chaque diaphragme indique une serie droit Modele gauche gauche de signes graves (I, II, III, X ou rien) en JGP328 haut. JGP330 Ces signes indiquent I'emplacement JGP933 precis de chaque diaphragme sur le JGP940 brQleur de la table de cuisson.
  • Page 32 Instructions d'instaliation CONVERSION AU GAZ PROPANE (SUITE) AJUSTEZ LES FLAMMES Continuez a ajuster en tournant lentement la vis jusqu'a ce que les BRULEURS flammes soient normales. Allumez tous les brQleurs au maximum Essai de stabilite de la flamme et verifiez les flammes.

This manual is also suitable for:

Jgp330Jgp933Jgp945Jgp940

Table of Contents