Page 1
130" Sealed GasCooktop nstructlons JGP 0, I Iinstallation JGP940, JGP945 ir_- I Questions? Call 800.GE.CARES In Canada, call 1.800.361.3400 (800.432.2737) or Visit our Website or Visit our Website at: www.geappliances.ca at: www.GEAppliances.com IN THE COMMONWEALTH FOR YOUR SAFETY: MASSACHUSETTS: -&WARNING - Iftheinformation •...
Installation Instructions IMPORTANT SAFETY INSTRUCTIONS ELECTRICAL REQUIREMENTS PARTS INCLUDED This appliance must be supplied with the proper voltage and frequency and connected to an individual, properly grounded branch circuit, protected by a circuit breaker or fuse 2 Screws Foam Tape having amperage as noted...
Installation Instructions PRE-INSTALLATION CHECKLIST Remove Installation Instructions from When preparing cooktop opening, make sure the inside of the cabinet literature pack and read them carefully the cooktop do not interfere with each before you begin. other. (See section on preparing Be sure to place all literature, Use and opening.)
Installation Instructions PREPARING THE OPENING _-I MAINTAIN THE FOLLOWING RECOMMENDED GAS SUPPLY MINIMUM CLEARANCE LOCATION FROM BACKWALL DIMENSIONS 1" Min. From Backwall 13" MAX. Depth of unprotected overhead cabinets 6" MIN. clearance from Recommended i cutout to side wall on _tas supply _13-1_ the right of the unit...
Installation Instructions INSTALLING THE COOKTOP UNIT LOCATE ELECTRICAL OUTLET [_] LOCATE MOUNTING PARTS AND GAS SHUT-OFF VALVE Remove the hold down brackets from BENEATH CABINET literature package. NEVER REUSE OLD CONNECTORS Shut off I] J\ WHEN INSTALLING THIS UNIT. _ Valve--_ i Electrical Outlet 12"...
Page 6
Installation Instructions INSTALLATION--GAS CONNECTIONS _-I PROVIDE ADEQUATE INSTALL REGULATOR ONTO GAS SUPPLY BURNER BOX BOTTOM This cooktop is designed to operate Screw natural gas at 4" of water column manifold regulator onto pressure and 7" of water column (W.C.) the burner supply pressure.
Installation Instructions CHECK FOR LEAKS INSTALLATION OVER BUILT-IN OVEN Before testing for leaks, make sure all burner knobs are in the OFF position. See built-in oven installation for complete installation instructions. After connecting the cooktop to gas, check system for leaks with a manometer.
Page 8
Installation Instructions INSTALLATION--ELECTRICAL CONNECTIONS -&WARNING - Disconnect _-I ELECTRICAL SUPPLY AND OUTLET electrical power at the main circuit breaker or fuse box before installing. An adequate electrical supply and outlet must be used to operate the electrical parts of your cooktop.
Page 9
Installation Instructions CAUTION: USAGE SITUATIONS WHERE Attaching the adaptor ground APPLIANCE POWER CORD terminal to the wall receptacle cover screw does not ground the appliance unless the WILL BE DISCONNECTED screw is metal, and not insulated, and the wall INFREQUENTLY receptacle is grounded through...
Installation Instructions COOKTOP BURNERS Make sure the Burner cap ASSEMBLING THE COOKTOP pins in the burner BURNERS heads match the The electrode of the spark igniter is exposed. burner base Be careful not to push any cooktop controls indentations Burner head while the top of the burner is removed,...
Installation Instructions CHECK IGNITERS THE BURNER FLAMES Operation of the electric igniters should Turn each burner on. Flames should be blue checked after the cooktop and supply line in color with no trace of yellow. The burner have been carefully checked for leaks and flames...
Installation Instructions OPERATION CHECKLIST Make sure all controls are left in the OFF When ordering parts, always include position, Check to be sure the cooktop serial number, model number and a code in the UNLOCKED position (on models letter to ensure proper replacement parts.
Installation Instructions MAKING THE LP CONVERSION ADJUST YOUR COOKTOP FOR SAFETY INFORMATION SHOULD KNOW USE WITH LP GAS The pressure regulator and burner orifices Disconnect all electrical power, at the main circuit breaker or fuse box. are set for natural gas.
Page 14
Installation Instructions MAKING THE LP CONVERSION (CONT.) CHANGE COOKTOP BURNER CHANGE COOKTOP BURNER ORIFICES ORIFICES (CONT.) NOTE: On most burners, Remove the top grates, burner caps, the orifices have a spring- Retainer and burner heads. Remove loaded retaining ring Ring This around the hex head to...
Page 15
Left Rear LeftFront RightFront These marks denote the precise location Model Orifice Orifice Orifice each orifice to the cooktop burner. JGP328 OOOO JGP330 JGP933 JGP940 18,000 BTU/HR Burner (on some models) JGP945 Replace: With: Main 206XN ..-) I08XL Simmer --) 34L with markings located in the sides only.
Installation Instructions MAKING THE LP CONVERSION (CONT.) ADJUST BURNER FLAMES Make the adjustment by slowly turning the screw until flame appearance Turn all burners full on and check correct. flames. They should be blue in color with Testing Flame Stability: some yellow tipping...