Before begin--Read these instructions completely carefully. IMPORTANT: Save these instructions local inspector's use. IMPORTANT: OBSERVE ALL GOVERNING CODES AND ORDINANCES. NOTE TO INSTALLER: Be sure to leave these instructions with the Consumer. NOTE TO CONSUMER: Keep these instructions with your Care Book future...
Gas Cooktop Component, Available cooktops in a variety of cooking technologies with right hand controls to meet any cooking need. ZGW125EN3 ZEW145V Gas Cooktop Component, with left hand controls Halogen and Ribbon Component ZEW155N JXBA55...
Page 4
Design Information Component Cooktop 5_stem ZEW166Y Product Downdraft Grill Cooktop Component Dimensions (240 volt) Parts supplied: • Grease collection • 48" flexible conduit 14-I/2" • One set clamping screws • One downdraft joiner strip JXBA55 • blower motor assembly -Shipped With Discharge On NOTE: The downdraft plenum is shipped with the discharge Left Side...
Design Information Component Cooktop _wtem Installation Joinei" sti'ips and end caps are included provide a finished look to any modular Accessories cooktop ai,i'angement. Provided EndCap Downdraft Joiner Downdraft Joiner EndCap Advance • ConsideI" base cabinet stoi'age ai`i'angements • Always t)i`e-plan electrical and gas to accommodate...
Cabinetry Component Cooktop _v_tem Installation • Whenever possible, avoid placing cabineti directly above the cooking surface. Location • If cabinetry is used above tile cooking surface: Use cabinets no more than 13" deep. Maintain 30" nAnimum clearance between cooktop(s) unprotected cabinets directly above the cooktop.
Cabinetry Component Cooktop _vstem For Gas Components: Tools & • Carpenter's square • Pipe wrench • Measuring tape Materials • Gas line to reach installation location • Saw • Gas resistant pipe joint sealant. • #2 Phillips head screwdriver bit socket Required •...
Page 8
Cabinetry Conlponent Cooktop _vstem Cutout If your configuration is not shown in the previous size. For each of the following components, add the charts, use tile following chart to calculate your cutout dimensions given. Information (dontint,ed) Component/Connector Model/Name Width Quantity Total Width Halogen...
Page 9
Cabinetry Component Cooktop _vstem Cutout If multiple components will be attached together, determine dimension A fl'om the following: information: Unit Unit Unit Unit 4 Unit multiple Halogen Halogen 29 3/4" component units RH Gas RH Gas LH(-;as LHGas Halogen Updraft 30 5/8"...
Ductwork Conlponent Cooktop _vstem Through Floor Between Joists Through Floor & Under Joists Multiple cooktops and downdrafl vent units may be used in a single arrangement. • Plan the route for venting exhaust to the outdoors. • Ductwork nmst be vented to outdoors - never to a crawl space,...
Ductwork Conlponent Cooktop _vstem Determine Ductwork Location 6"90° Elbow 6"90° Elbow (not Discharge left side (not to scale) Dischargeright side (not to scale) accurately locate the ductwork holes in the cabinet floor: • Place all components into the cutout, arranged in the exact position they will be...
Page 12
Actual length of straight duct plus duct fitting Total Duct Rtm, suchasthose publishedby NFPA andASHRAE. equivalent. Equivalent length of duct pieces are based on actual tests conducted by GE Evaluation Engineer- ing and reflect requirements for good venting performance with any downdrafl cooktop.
Page 13
Gas and Electrical Supply Component Cooktop _vstem • Gas components designed to operate Unit natural gas at 4" water column pressure. Supply These cooktops supplied with 1/2" 2-I/2" Location male gas connections. connection from Rear Edge of Cutout models with right hand controls...
Page 14
Installation Component Cooktop _vstem Apply foam tape (supplied) on top surface countertop along all edges of the cutout, Apply Gasket Strip • Turn all control knobs position. • Carefully remove knobs by lifting straight • Remove all grates, burner caps and vent conlponents.
Page 15
Installation Component Cooktop _vstem Attach chassis support brace to different Joining height cooktops Mtdtiple • When attaching grill to halogen or gas, place the support brace as shown. Cooktops • Remove screw fl'om the center of each Gasor Grill (Continued) Halogen cooktop chassis.
Installation Component Cooktop _vstem Joining Multiple Cooktops (Continued) Front of Countertop Joining additional cooktop to downdraft vent • Place cooktop next to downdraft vent in the cutout. or to downdraf| grill • Remove endcap on the side of the next •...
Installation Component Cooktop _vstem • Install the supplied pressure regulator in gas supply line as close to the cooktop irflet as not use a flame possible. Allowances for ventilation ducting check for leaks. may be required. Connect - The regu later should be installed with the...
Page 18
Connect only black, red and bare wires as showl-I, Model Voltage Frequency AMPS Electrical ZGW124EN3 60 Hz Power ZGW125EN3 60 Hz ZEW145V 60 Hz 11.0 Requirements ZEW145V 60 Hz 12.7 ZEW155N 60 Hz ZEW166Y 60 Hz 13.5 ZEW176Y 60 Hz...
Page 19
Installation Component Cooktop _v_tem Install downdraft vent filter Finalize • Place filter into opening on top ilter Installation supports. • Place grille over tile filter. Grille Removed Electric Components: _¢¢._Burner Push in and turn each knob to high position. Make sure each element...
Page 20
Pub No 49 8834 1 800 ddd 18d5. Dwg. No 164D3333P076 at Gtq_+,ral NO'It : Product imprt>vtqntqat is a c+>ntinuing endeavor ', 1997 GE Appliances [qectlic ]her+,R>r+., materials, ;mpealanct. 7rod sp+_cmcali_ns ar+_ s_d+ject Printed il_ USA Monogram; _ change withotl{...
Need help?
Do you have a question about the Monogram ZEW145V and is the answer not in the manual?
Questions and answers