Advertisement
Bulk Trigger Mode & Sequential Trigger Mode
These new XCL-C Series cameras feature advanced Bulk
Trigger and Sequential Trigger modes in addition to a
conventional trigger mode. Each camera supports 16
memory channels that can store up to 16 different camera
setups (e.g., exposure, and gain).
Bulk Trigger mode allows these cameras to capture up to
16 images in rapid succession using a single software or
hardware trigger.
Sequential Trigger mode allows each camera to capture a
single image using successive setups stored in the memory
channels with each software or hardware trigger.
1
2
3
CH 1
CH 2
CH 3
Sequential Trigger mode
Near-infrared Sensitivity
Utilizing Sony's EXview HAD CCD II technology enables the
XCL-C280 to capture clear images in NIR (near-infrared)
wavelengths. When used with an infrared strobe, the camera
produces outstanding picture quality especially in low light
and NIR inspection applications.
PIN ASSIGNMENTS
DC IN
DC IN (DC power input) connector (12-pin)
Pin No.
Signal
Pin No.
1
Ground
5
2
DC 12 V
6
3
Ground
7
4
GPO1*
8
1
*1 Signal output from pin 4, 6, 9 (GPO1/2/3) of DC IN connector
This setting allows you to select from exposure signal, strobe control signal,
Hi/Low fixed value, etc. The initial values of GPO1/2/3 are all Hi fixed.
*2 Signal output from pin 7, 10, 11 (GPI3/2/1) of DC IN connector
Function as GPI input or trigger input. The initial setting is GPI 1 for trigger
input and GPI 2/3 for GPI input.
DIGITAL IF (Interface) connector (26-pin mini conector)
Pin No.
Signal
1
Power supply or Ground*
2
X0–
3
X1–
4
X2–
5
XCLK–
6
X3–
7
SerTC+
8
SerTFG–
9
CC1–
10
CC2+
11
CC3–
12
CC4+
13
Ground
* The connection differs depending on the type of camera module
interface board you use.
In the case of PoCL support: Both the 1st pin and 26th pin are power supply.
In the case of non-PoCL support: Both the 1st pin and 26th pin are ground.
1
CH 1
CH 2
CH 3
Bulk Trigger mode
Simulated images
DIGITAL IF
Signal
Pin No.
Signal
Ground
9
GPO3*
1
GPO2*
10
GPI2*
1
2
GPI3*
11
GPI1*
2
2
Ground
12
Ground
Pin.No.
Signal
14
Ground
15
X0+
16
X1+
17
X2+
18
XCLK+
19
X3+
20
SerTC–
21
SerTFG+
22
CC1+
23
CC2–
24
CC3+
25
CC4–
26
Power supply or Ground*
Look-up Table (LUT)
Each XCL-C Series camera supports a look-up table which
transforms the input luminance signal into the required
digital output. It supports factory presets – Linear, Negative,
Binarization, and Linear Interpolation – as well as a User-
defined LUT (input: 12 bits, output: 12 bits).
Trigger Noise Filtering
With a trigger line filter, these cameras can specify a valid
pulse width for the trigger. This helps avoid unexpected
image capture caused, for example, by triggers from
insignificant noise.
Pulse Train Generator
XCL-C Series cameras are capable of outputting any
rectangular wave from one of the general-purpose outputs.
This pulse train can be programmed for frequencies from
0.5 Hz up to 100 KHz in 1 µs steps to control external devices
such as LED lights, simplifying overall system configuration.
DIMENSIONS
2-M2 Depth 3
1
/
(29)
3
16
4-M2 Depth 3
3-M2 Depth 3
OPTIONAL ACCESSORIES
VCT-333I
Tripod Adaptor
Unit: mm (inches)
/
(14.5)
19
32
/
1
/
1
3
2
16
(12)
(30)
/
(15)
/
(23.7)
19
15
32
16
/
(22)
/
7
21
8
32
(16.5)
1
/
(42)
11
16
Advertisement
