Vox Tonelab LE Owner's Manual page 39

6. TEXTREM
............................ Stereo In/Stereo Out 2
This models the popular tremolo circuit that's built
into the BLACK 2x12 model. The SPREAD set-
ting lets you produce a panning effect that
spreads to left and right.
[1] "SPEED"................................. 1.00...10.00 [Hz]
* Adjusts the tremolo speed.
[2] "DEPTH".............................................0.0...10.0
* Adjusts the tremolo depth.
[5] "SPREAD" ..........................................0.0...10.0
Adjusts the left/right spaciousness.
[6] "LEVEL"..............................................1.0...10.0
* Adjusts the output level.
7. ROTARY
.................................Mono In/Stereo Out 2
This models a stereo rotary speaker. When you
adjust the speed, it will take a certain amount of
time for the specified speed to be reached — just
like on an actual rotary speaker. This is because
it takes several seconds for the motor that cre-
ates the rotation to accelerate or decelerate.
[1] "SPEED 1"................................ 0.80...10.0 [Hz]
* Adjusts the rotational speed of the speaker. If
you assign "ROT SPD" to the CONTROL
switch, this will be the SLOW speed. This
knob is effective even if you're not using the
CONTROL switch. (p.49 Control switch set-
tings)
[2] "DEPTH"...........................................0.0...10.00
* Adjusts the modulation depth.
[4] "SPEED 2"................................ 0.80...10.0 [Hz]
* Adjusts the rotational speed of the speaker. If
you assign "ROT SPD" to the CONTROL
switch, this will be the FAST speed. This knob
will not function if you're not using the CON-
TROL switch. (p.49 Control switch settings)
[5] "ACCEL" .............................................1.0...10.0
* Adjusts the time it takes for the rotational
speed to change. With higher settings, the
change will take more time.
CONTROL switch ....................................ROT SPD
If you select "ROT SPD" as the CONTROL
switch setting, the rotation speed will alternate
between SLOW/FAST (SPEED 1/SPEED 2)
each time you press the CONTROL switch. This
lets you control the effect just as on an actual
rotary speaker. (p.49 Control switch settings)
8. PITCH SHIFTER (PITCH)
This is a pitch shifter with a range of two octaves
up or down, rivaling sophisticated rack-mounted
signal processors.
PITCH SHIFTER TIPS: If you assign the PITCH
knob to an expression pedal, you can use the
pedal to control the pitch change. ( p.47 Using the
expression pedal to control the sound)
[1] "PITCH" ..............................................–24...+24
* Adjusts the pitch in 100-cent units.
[2] "FINE".................................................–50...+50
* Adjusts the pitch in one-cent units.
[4] "TRACKING" ................................ 10...150 [ms]
[5] "DIRECT" ........................................... 0.0...10.0
[6] "EFFECT" .......................................... 0.0...10.0
9. MOD DELAY (MOD DLY)
(Mode=1) Mono In/Mono Out 3 (Mode=2) Mono In/Ste-
reo Out 1 (Mode=3)
This models an analog delay that lets you add a
vibrato effect to the delayed sound. The actual
unit provided 400 ms of delay time, but this simu-
lation extends this up to 1400 ms while maintain-
ing the same warm sound, and can also be used
as a sub-delay for the DELAY section.
[1] "SPEED" ...............................0.100...10.00 [Hz]
[2] "DEPTH" ............................................ 0.0...10.0
[3] "FEEDBACK" ..................................... 0.0...10.0
[4] "TIME"................................................ 1.0...10.0
[5] "MODE"..................................................... 1,2,3
[6] "MIX" .................................................. 0.0...10.0
10. FILTRON
This is an envelope controlled filter — a filter that
opens and closes according to the guitar input.
By assigning the MANUAL knob to the expres-
sion pedal you can simulate Korg's TRAVELER
pedal.
[1] "ATTACK" ........................................... 1.0...10.0
... Mono In/Mono Out 1
[2] "DEPTH" ............................................ 0.0...10.0
[3] "RESO" .............................................. 0.0...10.0
[4] "MANUAL".......................................... 1.0...10.0
[5] "POLARITY".....................uP (UP), dn (DOWN)
[6] "SENS"............................................... 0.0...10.0
39
Adjusts the tracking of the pitch shifter (i.e., how
closely it will follow). Shorter settings are effec-
tive if the PITCH setting is close to 0, and longer
settings are effective if the PITCH setting is
close to +/–24. While listening to the pitch-
shifted sound, adjust this so that you do not
have difficulty playing.
* Adjusts the level of the direct sound.
* Adjusts the level of the effect.
* Adjusts the modulation speed.
* Adjusts the modulation depth.
* Adjusts the amount of feedback.
* Specifies the delay time.
Selects the output method.
1: Mono output.
2: Stereo mode with the effect sound from
the right and dry sound from the left.
3: Reverse-phase stereo mode with dry +
effect in the left side and dry — effect in
the right side.
* Adjusts the mix amount of the effect.
........................... Stereo In/Stereo Out 2
* Adjusts the speed of response.
* Adjusts the depth of the effect.
* Adjusts the amount of resonance.
* Sets the cutoff frequency. If DEPTH is set to
10, MANUAL will not function.
Specifies the direction of movement.
* Adjusts the sensitivity of response to the gui-
tar volume.
...Mono In/Mono Out 1