Yamaha DTX900M Owner's Manual page 77

Paramater
name
NoisModDpt Determines the depth of the noise modulation.
NoisModSpd Determines the speed of the noise modulation.
NoisTon Determines the characteristics of the noise.
On/Off Turns the isolator on or off.
Determines the frequency for modulating the input
OSCFrqCors
wave.
Finely determines the frequency for modulating the
OSCFrqFine
input wave.
OutGain Determines the level gain.
OutLvl Determines the output level.
OutLvl1 Determines the output level for the 1st series.
OutLvl2 Determines the output level for the 2nd series.
Output Determines the output level.
Determines the degree and character of the distor-
OverDr
tion effect.
Pan1 Determines the pan position for the 1st series.
Pan2 Determines the pan position for the 2nd series.
This parameter of the Slice effect determines the
PanAEGLvl minimum level of the AEG applied to the panned
sound.
This parameter of the Slice effect determines the
PanAEGType
type of the AEG applied to the panned sound
PanDirectn Determines the type of the Auto Pan.
PanDpth Determines the depth of the pan effect.
PanType Determines the pan type.
PhShiftOfst Determines the offset value of the phase modulation.
Pitch1 Determines the pitch in semitones for the 1st series.
Pitch2 Determines the pitch in semitones for the 2nd series.
PMDepth Determines the depth of the pitch modulation.
Determines the Cutoff frequency of the Low Pass Fil-
Pre-LPF
ter before the modulation.
Determines the Resonance of the Low Pass Filter for
PreLPFReso
the input sound.
Determines the Cutoff frequency of the High Pass
PreModHPF
Filter before the modulation.
This guitar amp effect parameter controls the high
Presenc
frequencies.
Ratio Determines the ratio of the compressor.
Determines the release curve of the envelope fol-
RelCurv
lower.
Determines the amount of time that elapses between
Release the release or end of a sound and the end of the
compressor effect.
RelTime Determines the release time of the envelope follower.
Reso Determines the resonance of the filter.
ResoOfst Determines the resonance as offset.
Determines the delay time from the early reflections
RevDly
until the reverberations.
RevTime Determines the reverb time.
RoomSize Determines the room capacity.
Determines the volume balance of the horn and
Rotor/Horn
rotor.
Determines the speed of the rotor when the slow/fast
RotorF
switch is set to "fast."
Determines the speed of the rotor when the slow/fast
RotorS
switch is set to "slow."
[For FLANGER&PHASER effects, TECH effects]
Determines the sensitivity of the modulation applied
to the input change.
Sens
[For TOUCH WAH]
Determines the sensitivity of the wah filter's change
applied to the input change.
Determines how long it takes for the rotation speed of
the horn to change from the current speed (slow or
S-FTmHorn
fast) to another speed (fast or slow) when the rotation
speed is switched.
Descriptions
Basic Structure of the DTX900
Paramater
name
Determines how long it takes for the rotation speed of
the rotor to change from the current speed (slow or
S-FTmRotor
fast) to the another speed (fast or slow) when the
rotation speed is switched.
SmplFrqCtr Controls the sampling frequency.
SpcType Selects the type of space simulation.
Speaker Selects the type of speaker simulation.
[For FLANGER]
Determines the frequency of the LFO wave which
controls the cyclic change of the delay modulation.
[For PHASER MONO, PHASER STEREO]
Speed
Determines the frequency of the LFO wave which
controls the cyclic change of the phase modulation.
[For AUTO WAH]
Determines the speed of the LFO.
SpeedCtrl Switches the rotary speed.
Spread Determines the spread of the sound.
Stage Determines the step number of the phase shifter.
Determines the minimum input level at which the
Thresh
effect is applied.
*3
Top Determines the maximum value of the wah filter.
[For FLANGER]
Determines the type of flanger.
[For WAH effects]
Type
Determines the type of Wah.
[For EARLY REFLECTION]
Determines the type of the reflection sound.
Vowel Selects a vowel type.
Determines the wall status of the simulated room.
WallVary
Higher settings produces more diffuse reflections.
Width Determines the width of the simulated room.
Determines the resolution of the sound, or how
WordLen
"rough" the sound is.
*1 The Bottom parameter is available only when the value is less than
that of the Top parameter.
*2 The Color parameter may not be effective depending on the values
of the Mode and Stage parameters.
*3 The Top parameter is available only when the value is more than that
of the Bottom parameter.
Reference
Descriptions
75
DTX900 Owner's Manual