Tuning Your Television For The Vcr; Inserting Batteries In The Remote Control; Setting The Date And Time - Samsung SV-3000 Instruction Manual

Tuning Your Television for the VCR

GB
VCR STANDBY/ON TV STANDB
SLOW
2
SHUTTLE
REC MENU
4
OK
14
You must tune your television for the VCR only if you are not using
a RCA cable
To view pictures from your VCR when a RCA cable is
used, the television must be set to the audio/video mode
(AV).
1 Switch on the television.
2
Switch on the VCR by pressing STANDBY/ON on the front of the
VCR or VCR STANDBY/ON on the remote control.
3
Select a programme position on the television to be reserved for
use with your VCR.
4 Insert the video cassette in the VCR. Check that the VCR starts
❿ II
reading the cassette; if not, press
button.
5
Start a scan on your television or set the television to UHF
channel 36.
6
Fine tune the television until the pictures and sound are obtained
clearly.
7
If you cannot find the pictures and sound, or there is interference
from nearby channels, it may be necessary to change the setting
of the VCR output channel (see Setting the VCR Output Channel
on page 17 and Problems and Solutions on page 42).
8
When the picture and sound are perfectly clear, store this channel
at the desired programme position on the television.
Result: That programme is now reserved for use with your VCR.

Inserting Batteries in the Remote Control

You must insert or replace the batteries in the remote control when
you:
Purchase the video cassette recorder
Find that the remote control is no longer working
correctly
1
Push the tab in the direction of the arrow to release the battery
compartment cover on the rear of the remote control.
2
Insert two AA, R6 or equivalent batteries, taking care to respect
the polarities:
+ on the battery with + on the remote control
– on the battery with – on the remote control
3
Replace the cover by aligning it with the base of the remote
control and pushing it back into place.
Do not mix different battery types (manganese and
alkaline for example).

Setting the Date and Time

Your VCR contains a 24-hour clock and calendar used to:
Automatically stop programme recording
Preset your VCR to record a programme automatically
You must set the date and time when:
You purchase the video cassette recorder
The power supply remains off for more than 30 sec
(SV-910/SV-900/SV-810/SV-800 ONLY)
The power supply remains off for more than 1 hour
(SV-3000 ONLY)
Do not forget to reset the time when you change
clocks from winter to summer time and vice versa.
1
Press MENU on the remote control.
Result: The programming menu is displayed.
or ➛, ❿ buttons to select the
2 Press the corresponding ,
œ ❷
CLOCK SET option.
3
Press the OK button to select this option.
Result: The CLOCK SET menu is displayed.
Press ➛ or ❿ to select the hour, minutes, day, month and year.
4
Result: The option selected flashes.
5 Press the or buttons to increase or decrease the value.
œ ❷
Result: The day of the week is displayed automatically.
You can hold the œ or ❷ buttons down to scroll more
quickly through the values.
6
On completion, press MENU twice to exit the menu.
GB
1
REC MENU
2
2 2
OK
3
SPEED DUB TV/VCR TIMER
PROG OPTIONS INSTALL
CLOCK
CLOCK BONUS LANG
CLOCK SET
➛❿¤¤
OK END: MENU
œ ❷¤¤
CLOCK
12:00 1/JAN/2003
WED
➛❿¤¤¤¤¤¤¤¤¤¤¤
END: MENU
œ ❷
15