Table of Contents
Advertisement
Connecting with TV
In the initial SET, exclusive channel for video is set to CH 3. To change this setting, set again in "CHANNEL
SET" screen in VCR operation.
In connecting RF cable to TV, set TV channel to CH3.
Various methods in connecting with TV
<Rear Panel of DVD-VIDEO>
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK.
DO NOT REMOVE COVER (OR BACK).
REFER SERVICING TO QUALIFIED SERVICE PRESONNEL.
NO USER SERVICEABLE PARTS INSIDE.
AUDIO
20
19
21
14
15
17
18
16
8
13
11
9
12
10
3
4
6
7
5
1
3
VIDEO
<Rear Panel of TV>
Method 3
Method 4
S-VIDEO
1
1
Method
Method
Remove circular cable (RF cable) (surplus cable) plugged in "ANT.IN" Jack in rear panel of TV. Connect the
cable to "ANT.IN" jack in rear panel of DVD-Video. Connect TV to DVD-Video. Connect "RF OUT" jack in DVD-
Video with "ANT.IN" jack in TV with RF cable.
2
2
Method
Method
: Connecting to a TV that has a audio/video in jacks
Connect VIDEO OUT jack in DVD-Video to VIDEO IN jack in TV, and AUDIO OUT jack in DVD-Video to AUDIO
IN jack in TV with connecting cable of Audio/Video jack. Select VCR mode by pressing TV/INPUT button in TV,
you can view more clear screen and sound than connection with RF cable only.
3
3
Method
Method
: Connecting to a TV that has a component video in jacks
Use a component video cable (commercially available) in place of the yellow video cable to enjoy higher quality
pictures. The component video connection only supplies video (picture) in the DVD mode of the DVD-Video.
Therefore, in order to use the VCR features or view TV channels at the DVD-Video, you still need to either
connect the RF coaxial cable between the ANT-OUT jack of the DVD-Video and the TV's Antenna In jack, or
connect the video cable.
4
4
Method
Method
: Connecting to a TV that has a S-Video in jacks
Use a S-Video cable (not supplied) to enjoy higher quality pictures. Only in DVD mode, S-Video output is
available.
• VHF: 2 ~13 channels of TV , UHF: 14~69 channels of TV, CATV: Broadcasting is transmitted with cable from
broadcasting station by contract with the station and consumers. It does not need any antenna.
• In/Out jack in Audio/Video terminal: - In: A jack used to receive signal required in this unit from other units. -
Out: A jack used to send signal of this unit to other units.
• Connect with Audio/Video terminal, you can enjoy more clear video and audio. (Use OUTPUT button in this remote
control to select video mode.)
• If screen is broken in connecting COMPONENT Out to Pr, Pb, Y of TV COMPONENT In jack , connect to Cr, Cb, Y.
10
AUDIO OUT
COMPONENT OUT
OUT
IN
ANT.IN
Y
R
R
AUDIO
Pr
S-VIDEO OUT
L
L
DIGITAL AUDIO OUT
RF OUT
OPTICAL
COAXIAL
Pb
VIDEO
Method 1
Method 2
<Outside Antenna or Wall Antenna Outlet>
Connecting with Cable Box
You should install a distributor additionally.
How to connect
<Converter Box>
<Rear Panel of DVD-VIDEO>
IN
OUT
IN
R
AUDIO
OUT
L
VIDEO
<A/B Switch>
<Splitter (Not supported)>
RF Cable
OUT
IN
OUT
RF Cable
Connect one RF cable between one OUT terminal on the splitter and the IN terminal on the converter box.
Connect another RF cable between the other OUT terminal on the splitter and the A-IN terminal on an A/B
switch (available at your local electronics store.) Connect a third RF cable between the OUT terminal on the
converter box and the B-IN terminal on the A/B switch.
Connect a RF cable between the OUT terminal on the A/B switch and the ANT. IN on your DVD-VIDEO.
When the A/B switch is in the B position, use the converter box to change channels ; when the A/B switch is in
the A position, use the DVD-VIDEO to change channels.
How to watch general broadcasting with recording CATV
1
1
Set Channel Select switch of Converter Box to CH 3 or 4 as same as video exclusive channel. Press [SET]
button in [VCR] operation to set video exclusive channel in "CHANNEL SET" screen.
2
2
Press channel button of Converter Box to select channel to be recorded. In this case, if you want to watch
CATV to be recorded, press [TV/INPUT] button of TV to select "Out (VCR)".
3
3
Press [REC] button in DVD-Video.
4
4
To watch general broadcasting, press channel button in TV to select the desired channel.
• For some types of TV, you should press [TV/INPUT] button in TV remote control and convert from Out 1( VCR 1) or
Out 2(VCR 2) mode to Broadcasting Channel mode to change TV channel.
• Change channel selection of CATV receiver in recording, contents of recording is changed.
<Rear Panel of TV>
INPUT 1
INPUT 2
ANT.IN
ANT IN
RF OUT
RF Cable
AUDIO/VIDEO Cable
If your cable system only
requires you to use a converter
box for some channels
(i.e., pay-TV channels), follow
these steps: Find the primary
incoming RF cable. Plug this
<Cable Antenna>
cable into a splitter (available
at your local electronics store.)
11
Advertisement
Table of Contents
