Renault Koleos Owner's Handbook Manual
Renault Koleos Owner's Handbook Manual

Renault Koleos Owner's Handbook Manual

Hide thumbs Also See for Koleos:
Table of Contents

Advertisement

KOLEOS
DRIVER'S HANDBOOK

Advertisement

Table of Contents
loading

Summary of Contents for Renault Koleos

  • Page 1 KOLEOS DRIVER’S HANDBOOK...
  • Page 2 Warning: to ensure the engine operates optimally, the use of a lubricant may be restricted to certain vehicles. Please ELF has developed a complete range of lubricants for RENAULT: refer to your maintenance document. engine oils manual and automatic gearbox oils Benefiting from the research applied to Formula 1, lubricants are very high-tech products.
  • Page 3: Driving

    This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
  • Page 5: Table Of Contents

    Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
  • Page 7 Section 1: Getting to know your vehicle RENAULT cards: general information, use, deadlocking ....... . .
  • Page 8: Doors

    "Replace card battery" appears on the and never leave a child instrument panel (refer to the informa- (or a pet) unsupervised, even for a tion on the "RENAULT card: Battery" in short while. Section 5). They may pose a risk to themselves...
  • Page 9 Replacement: need for an Using the key additional RENAULT card Refer to the information on "Locking/ If you lose your RENAULT card or unlocking the doors". require another, you can obtain one Once you have accessed the vehicle from an approved dealer.
  • Page 10: Locking The Doors

    The dipped beam headlights, indicator erly shut, or if a RENAULT card is still in lights and interior lights come on for ap- the reader, the doors and boot quickly...
  • Page 11: Unlocking The Vehicle

    – one flash indicates that the vehi- cle is unlocked; – two flashes indicates that the vehicle is locked. Never leave your vehicle with the RENAULT card inside.
  • Page 12: Locking The Vehicle

    After this delay, the hands-free mode Note: a RENAULT card must be within is activated once again and any move- the vehicle's access zone (zone 1) to ment of a handle will unlock the vehicle.
  • Page 13 After locking or unlocking the vehi- cle doors or the tailgate only, using the buttons on the RENAULT card, hands-free unlocking is deactivated. To reactivate the “hands-free” mode: restart the vehicle.
  • Page 14 RENAULT cARd: deadlocking To lock the vehicle, without deadlocking Press button 2 or 3 twice. Note: to raise the windows simulta- neously, the second time the button is pressed, it must be held down for more than one second. The hazard warning lights flash twice to indicate that the doors have locked.
  • Page 15 If a door (or tailgate) is open or not With the doors unlocked or the “hands- properly closed, as soon as the vehi- free” RENAULT card in your posses- Lights-on reminder buzzer cle reaches a speed of approximately sion, hold handle 1 and pull it towards 9 mph (15 km/h), the message “Boot...
  • Page 16: Child Safety

    OpENINg ANd cLOsINg ThE dOORs (2/2) child safety Manually locking the rear doors Move lever 3 and check from the inside that the doors are securely locked, to prevent the rear doors being opened from the inside. driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-sufficient alone on your vehicle, even for a short time.
  • Page 17: Locking/Unlocking Doors

    Card; refer to the information on the RENAULT Card" in Section 1. In certain cases, the RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc. – use of appliances operating on the same frequency as the card (mobile phone, etc.);...
  • Page 18: Indicator Light

    RENAULT card When the ignition is on, the indicator (if the RENAULT card is not working, for light integrated in switch 4 informs you example) of the status of the doors and tailgate: With the engine switched off and a –...
  • Page 19: Operating Principle

    RAId (RENAULT ANTI-INTRUdER dEvIcE) Operating faults To activate this function: After switching on the ignition and If you experience an operating fault (no when the vehicle is stationary, you automatic locking, the indicator light in- have approximately 20 seconds to...
  • Page 20: Front Headrests/Seats

    fRONT hEAdREsTs To remove the headrest Raise the headrest as far as possible, then while pressing button 1, raise the headrest to release it. To refit the headrest Insert the headrest rods into the holes, with the notches facing forwards. Hold down button 1 and move the headrest to the required height.
  • Page 21: Front Seats

    fRONT sEATs (1/2) To raise or lower the seat base (depending on vehicle) Move lever 4 as required: – move it upwards to raise the seat; – move it downwards to lower the seat. To tilt the seatback Move lever 5 to control the angle of the seatback.
  • Page 22: Heated Seats

    fRONT sEATs (2/2) heated seats To fold down the passenger seat To adjust the lumbar support on the Depending on the vehicle, the passen- driver’s seat: (depending on vehicle) ger seatback may be folded down onto Move lever 7. With the engine running, press the seat base to create a table.
  • Page 23: Seat Belts

    sEAT BELTs (1/2) Before starting, first adjust your driv- Always wear your seat belt when trav- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
  • Page 24 sEAT BELTs (2/2) ™ fastening Adjusting the height of the front passenger seat belt re- minder warning light front seat belts Unwind the belt slowly and smoothly (depending on the vehicle) and ensure that buckle 3 locks into Press button 8 to adjust the seat belt This comes on the central display 6 catch 5 (check that it is locked by pull- height so that the shoulder strap 1 is...
  • Page 25: Rear Seat Belts

    REAR sEAT BELTs side seat belt centre seat belt Hold the buckle 1 and pull slowly on the Hold the buckle 4 and pull slowly on the belt. belt. Place the upper section of the belt as Place the upper section of the belt as close to your shoulder as possible and close to your shoulder as possible and the lower section as close to your pelvis...
  • Page 26 sEAT BELTs warnings The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: belts, seats and their mountings. For special operations (e.g. fitting child seats) contact an authorised dealer. –...
  • Page 27 METhOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretension- an accident. ers 1; – No operation whatso- –...
  • Page 28: Methods Of Restraint In Addition To The Front Seat Belts

    METhOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (2/4) force limiter Air bags for driver and front passenger Above a certain level of impact force, this mechanism is used to limit the force An “airbag” marking on the steer- of the belt against the chest so that it is ing wheel and the dashboard (airbag at an acceptable level.
  • Page 29 METhOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (3/4) Operation Operating faults This system is only operational when Warning light 4 will light up on the in- the ignition is switched on. strument panel when the ignition is switched on and then go out after a few In a severe frontal impact, the air bags seconds.
  • Page 30 METhOds Of REsTRAINT IN AddITION TO ThE fRONT sEAT BELTs (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
  • Page 31: To The Rear Seat Belts

    METhOds Of REsTRAINT IN AddITION TO ThE REAR sEAT BELTs force limiter Above a certain level of impact force, this mechanism is used to limit the force of the belt against the chest so that it is at an acceptable level. –...
  • Page 32 sIdE pROTEcTION dEvIcEs side air bags This air bag is fitted to each of the front seats and is inflated at the sides of the seats (door side) to protect the oc- cupants in the event of a severe side impact.
  • Page 33: Additional Methods Of Restraint

    AddITIONAL METhOds Of REsTRAINT All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. The air bag is designed to complement the action of the seat belt.
  • Page 34: Child Safety: General Information

    chILd sAfETY: general information (1/2) carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- driver’s responsibility ished growing.
  • Page 35 chILd sAfETY: general information (2/2) Using a child seat Set a good example by always fas- The level of protection offered by the tening your seat belt and teaching child seat depends on its ability to re- your child: strain your child and on its installation. –...
  • Page 36 chILd sAfETY: choosing a child seat Rear-facing child seats forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
  • Page 37: Choosing A Child Seat Mounting

    chILd sAfETY: choosing a child seat mounting (1/2) There are two ways of attaching child Attachment using the IsOfIX seats: via the seat belt or using the system ISOFIX system. Authorised ISOFIX child seats are ap- proved in accordance with regulation Attachment via the seat belt ECE-R44 in one of the three following The seat belt must be adjusted to...
  • Page 38 chILd sAfETY: choosing a child seat mounting (2/2) Fit the hook of the strap onto ring 3 and pull the strap so that the seatback of the child seat comes into contact with the top of the seatback on the vehicle seat. The two rings 1 are located between The third ring is used to attach the the seatback and the seat base (behind...
  • Page 39: Fitting A Child Seat

    chILd sAfETY: fitting a child seat (1/3) In the front seat In the rear side seat Some seats are not suitable for fitting child seats. The diagram on the follow- The laws concerning children travel- A carrycot can be installed across the ing page shows you how to attach a ling in the front passenger seat differ in vehicle and will take up at least two...
  • Page 40 chILd sAfETY: fitting a child seat (2/3) child seat attached using the IsOfIX mounting ü seat which allows an ISOFIX child seat to be fitted. ± the rear seats are fitted with an anchorage point which allows a for- ward-facing ISOFIX child seat with uni- versal approval to be fitted.
  • Page 41 chILd sAfETY: fitting a child seat (3/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the regu- lations in force are respected. seat size Weight of passenger front Type of child seat Rear side seats Rear centre seat the child...
  • Page 42 chILd sAfETY: deactivating, activating the front passenger air bag (1/3) dANgER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEvER fit a rear-facing child seat on a front passenger seat with an active front air bag.
  • Page 43 chILd sAfETY: deactivating, activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of the passen- ger sun visor 3 (example: label shown above) remind you of these instruc- tions. dANgER Since operation of the front passenger air bag is not compatible with the position of a rear-facing child seat, NEvER...
  • Page 44: Deactivating/Activating The Front Passenger Airbags

    chILd sAfETY: deactivating, activating the front passenger air bag (3/3) It is forbidden to fit a rear-facing child seat to the front passenger seat if the air bag activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended. Activating the front Operating faults passenger air bags...
  • Page 45: Clock And Exterior Temperature

    cLOcK ANd EXTERNAL TEMpERATURE External temperature indicator special note: When the outside temperature is –3°C to +3°C, the °C characters flash (signal- ling a risk of black ice on the road). Note: in some cases (vehicle stopped for less than 3 hrs 30 mins), the infor- mation displayed on the screen when the ignition is switched on may be in- correct.
  • Page 46: Driving Position

    dRIvINg pOsITION: LEfT-hANd dRIvE (1/2) 9 10 11 12 29 28 27 1.40...
  • Page 47 dRIvINg pOsITION: LEfT-hANd dRIvE (2/2) The equipment fitted, described below, dEpENds ON ThE vERsION ANd cOUNTRY. 1 Vents 9 Display (depending on the vehicle) 22 Switch for: of time, temperature, radio informa- 2 Stalk for: – Hill Descent Control (HDC); tion, navigation system information, –...
  • Page 48 dRIvINg pOsITION: RIghT-hANd dRIvE (1/2) 1.42...
  • Page 49 dRIvINg pOsITION: RIghT-hANd dRIvE (2/2) The fittings described below dEpENd ON ThE vEhIcLE EQUIpMENT ANd cOUNTRY. 1 Vents 11 Instrument panel. 18 Cruise control/speed limiter con- trols. 2 Location for passenger air bag. 12 Location of driver’s air bag and horn. 19 Passenger seat belt indicator light.
  • Page 50: Warning Lights

    WARNINg LIghTs (1/4) The presence and operation of the warning lights dEpENd ON ThE EQUIpMENT ANd cOUNTRY. å Ä Air bag warning light Toxic fume filter system This comes on when the igni- Warning Light tion is switched on and goes out after a This lights up when the ignition is few seconds.
  • Page 51: Electronic Parking Brake

    WARNINg LIghTs (2/4) The presence and operation of the warning lights dEpENd ON ThE EQUIpMENT ANd cOUNTRY. Ú sTOp light Battery charge warning light ® This lights up when the ignition If the light comes on accompa- ® is switched on and goes out as soon as nied by the warning light, this in- the engine is started.
  • Page 52 WARNINg LIghTs (3/4) The presence and operation of the warning lights dEpENd ON ThE EQUIpMENT ANd cOUNTRY. Ü fuel gauge warning light particle filter warning light (depending on the vehicle) If this warning light lights up or flashes, fill the tank as soon as possi- Refer to the information on “Special ble.
  • Page 53 WARNINg LIghTs (4/4) The presence and operation of the warning lights dEpENd ON ThE EQUIpMENT ANd cOUNTRY. ™ front seat belt reminder Anti-lock braking warning side light tell-tale light warning light light á This comes on when the engine is This comes on when the ignition is headlight main beam tell- started then, if the driver’s or front pas-...
  • Page 54: Instrument Panel

    INsTRUMENT pANEL: displays and indicators (1/2) coolant temperature indicator In normal use, the needle 6 should be positioned before mark 5. It may ap- proach mark 5 under severe conditions of use. ® There is a warning only if the indicator and engine overheating indi- cator 4 come on along with the mes- sage “Engine overheating”...
  • Page 55: Trip Computer And Warning System

    INsTRUMENT pANEL: displays and indicators (2/2) Engine oil level low warning 7 Information display 8 The display warns the driver if the Depending on the vehicle, the following engine oil level is low when the ignition information is shown on display 8: is switched on.
  • Page 56 TRIp cOMpUTER ANd WARNINg sYsTEM (1/10) c) mileage before service; d) programmed speed (speed limiter/ cruise control); e) trip log, operating faults and informa- tion message readout. Trip computer and warning display selection buttons 2 system 1 and 3 This includes the following functions: Scroll through the following informa- tion upwards (button 2) or downwards –...
  • Page 57 TRIp cOMpUTER ANd WARNINg sYsTEM (2/10) Interpreting some of the Automatic resetting of the values displayed after journey parameters resetting Resetting occurs automatically when the maximum value of any of the pa- The values showing average fuel con- rameters is exceeded. sumption, range and average speed will become more stable and reliable the further you travel after pressing the...
  • Page 58 TRIp cOMpUTER ANd WARNINg sYsTEM (3/10) The display of information shown below dEpENds ON ThE vEhIcLE EQUIpMENT ANd cOUNTRY. Examples of selections Interpreting the display selected a) Total mileage and trip mileage recorder. b) Journey parameters. fuel used since the last reset. Average fuel consumption since the last reset.
  • Page 59 TRIp cOMpUTER ANd WARNINg sYsTEM (4/10) The display of information shown below dEpENds ON ThE vEhIcLE EQUIpMENT ANd cOUNTRY. Examples of selections Interpreting the display selected current fuel consumption. This value is displayed above a speed of approximately 20 mph (30 km/h). Estimated range with remaining fuel.
  • Page 60 TRIp cOMpUTER ANd WARNINg sYsTEM (5/10) The display of information shown below dEpENds ON ThE vEhIcLE EQUIpMENT ANd cOUNTRY. Examples of selections Interpreting the display selected c) Mileage before service. Distance remaining before the next service. When the distance value approaches the limit, there are several possible scenarios: –...
  • Page 61 TRIp cOMpUTER ANd WARNINg sYsTEM (6/10) Journey parameters The display of information shown below dEpENds ON ThE vEhIcLE EQUIpMENT ANd cOUNTRY. Examples of selections Interpreting the display selected e) cruise control/speed limiter programmed speed. Refer to the information on the “Cruise control/Speed limiter” in Section 2. g) computer log.
  • Page 62: Information Messages

    Interpretation of messages “Top up oil level” Top up as soon as possible. The card battery charge is too low (refer to the information on the “Renault card: “Replace card battery” battery” in section 5). Indicates the presence of water in the diesel filter; contact your authorised dealer “Bleed diesel filter”...
  • Page 63 TRIp cOMpUTER ANd WARNINg sYsTEM (8/10) Operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. ©...
  • Page 64: Warning Messages

    TRIp cOMpUTER ANd WARNINg sYsTEM (9/10) Warning messages ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. stop your engine and do not restart it. contact an approved dealer. Examples of warning messages are given in the following pages.
  • Page 65 TRIp cOMpUTER ANd WARNINg sYsTEM (10/10) Warning messages ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traffic conditions allow. stop your engine and do not restart it. contact an approved dealer. Examples of warning messages are given in the following pages.
  • Page 66: Steering Wheel

    sTEERINg WhEEL/pOWER-AssIsTEd sTEERINg variable power-assisted Operating faults steering – If the message “Check power steer- ing” is displayed on the instrument It is equipped with a system which © panel accompanied by the adapts the level of assistance to the ve- warning light, consult an authorised hicle speed.
  • Page 67: Rear-View Mirrors

    REAR vIEW MIRRORs folding door mirrors With the engine running, move button 1 to position F: the door mirrors fold away. To reset them for driving, return to posi- tion C, D or E. heated door mirrors Mirror de-icing is carried out at the same time as rear screen de-icing.
  • Page 68: Audible And Visual Signals

    AUdIBLE ANd vIsUAL sIgNALs direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. When driving on the motorway, the steering wheel is not often turned enough to return the stalk automatically to 0.
  • Page 69: Exterior Lighting And Signals

    EXTERIOR LIghTINg ANd sIgNALs (1/3) á Main beam headlights With the dipped beam head- lights lit, push stalk 1 forwards. This indicator light on the instrument panel comes on. To return to the dipped headlight posi- tion, pull the stalk 1 towards you again. If the headlights are off, you can pull stalk 1 towards you to flash the head- lights.
  • Page 70: Switching Off The Lights

    EXTERIOR LIghTINg ANd sIgNALs (2/3) switching off the lights “see-me-home lighting” function There are two possibilities: This function (useful, for example, for – manually, move ring 3 to the OFF po- opening a gate, garage, etc.) enables sition; you to switch the dipped headlights on –...
  • Page 71: Rear Fog Light

    EXTERIOR LIghTINg ANd sIgNALs (3/3) Rear fog light Turning off the front and rear fog lights. Turn the centre ring 5 on the stalk until the symbol is opposite Turn the ring 5 until the mark 4 is oppo- mark 4, then release it. site the OFF symbol.
  • Page 72: Electric Beam Height Adjustment

    ELEcTRIc BEAM hEIghT AdJUsTMENT Examples of positions for adjusting control A according to the load On equipped vehicles, control A allows you to adjust the height of the beams according to the load. Turn control A downwards to lower the headlights and upwards to raise them.
  • Page 73 WINdscREEN WAsh, WIpE (1/2) vehicle fitted with front windscreen wiper rain sensor A Wiping on request The stalk returns to position B when released. B Off C Automatic wiper function When this position is selected, the system detects water on the wind- screen and triggers the wipers at a suitable wiping speed.
  • Page 74: Windscreen Washer

    WINdscREEN WAsh, WIpE (2/2) headlights on The headlight washers will be activated at the same time. In freezing or snowy weather, ensure they are not stuck to the windscreen (including the central area located behind the interior rear-view mirror) and the rear screen before starting the wipers (risk of motor overheat- Windscreen washer, ing).
  • Page 75: Special Note

    REAR scREEN WAsh, WIpE Rear screen wash/wipe To use this, push stalk 1. A longer pull activates the windscreen washers and four sweeps of the wind- screen wipers followed by one sweep a few seconds later. special note If the windscreen wipers are opera- tional when you select reverse gear, the rear screen is wiped intermittently.
  • Page 76: Fuel Tank

    fUEL TANK (1/3) diesel versions It is essential to use diesel fuel that conforms with the information given on the label inside cover A. petrol versions It is essential to use unleaded petrol. The octane rating (RON) must conform with the information given on the label on cover A.
  • Page 77 fUEL TANK (2/3) vehicles running on ethanol-based filling with fuel persistent smell of fuel Insert the nozzle fully before beginning fuel It is essential to use unleaded petrol or to fill the tank (risk of splashback). fuel containing a maximum of 85% eth- If you notice a persistent Keep the nozzle in this position anol (E85).
  • Page 78 fUEL TANK (3/3) The engine can then be restarted; if it still does not run properly, allow it to run at idle. If the engine does not start after several attempts, contact an authorised dealer. No modifications what- soever are permitted on any part of the fuel supply system (electronic unit, Running out of fuel on diesel...
  • Page 79 Section 2: Driving (Advice on use relating to fuel economy and the environment) Running in ..............Starting the engine .
  • Page 80: Running In

    RUNNING IN Petrol version Diesel version For the first 1,200 miles (2,000 km), For the first 900 miles (1,500 km), do not exceed 78 mph (130 km/h) in do not exceed 2,500 rpm. After com- top gear (or 3,000 to 3,500 rpm), and pleting this mileage you may drive change gears without over-revving the faster, although you may only expect...
  • Page 81: Starting The Engine

    When you get into the vehicle, insert the To start, depress the brake or clutch It is only possible to start the engine if RENAULT card fully into card reader 2. pedal and press button 1. If a gear the card is in the reader 2.
  • Page 82 (2/2) Operating faults In certain cases, the hands-free RENAULT card may not work: – when the RENAULT card battery is drained, flat battery, etc. – near to appliances operating on the same frequency as the card (moni- tor, mobile phone, video game, etc.);...
  • Page 83: Stopping The Engine

    “No keycard Press When leaving your vehi- and hold” appears on the instrument cle, in particular with the panel A: press button 1 for over two RENAULT card, check that seconds. the engine has completely stopped. Hands-free RENAULT card: With the card in the vehicle, press button 1: the engine will stop.
  • Page 84: Special Features Of Petrol Versions

    SPECIAL FEATURES OF PETROL vERSIONS The following operating conditions If you notice any of the above operating should be avoided: faults, have the necessary repairs car- ried out as soon as possible by an ap- – driving for long periods when the low proved dealer.
  • Page 85: Special Features Of Diesel Versions

    SPECIAL FEATURES OF DIESEL vERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection To avoid faults in icy weather: equipment which prevents the engine – ensure that the battery is always fully speed being exceeded irrespective of charged;...
  • Page 86: Special Features Of Diesel Versions Fitted With A Particle Filter

    SPECIAL FEATURES OF DIESEL vERSIONS FITTED wITH A PARTICLE FILTER Diesel engine speed Precautions to be taken in Ü winter Depending on the vehicle, the Diesel engines are fitted with injection warning light lights up on the instrument equipment which prevents the engine To avoid faults in icy weather: panel to show that there is a risk of the speed being exceeded irrespective of...
  • Page 87: Gear Lever

    GEAR LEvER/HANDBRAKE Handbrake To release Pull lever 4 upwards, press button 3 and then lower the lever to the floor. To apply Pull upwards, check that the vehicle is properly immobilised. When driving, ensure that the handbrake has been Selecting reverse gear vehicle with automatic gearbox: refer completely released (red to the information on the “Automatic...
  • Page 88: Electronic Parking Brake

    ELECTRONIC PARKING BRAKE (1/4) Automatic releasing of the electronic parking brake Indicator lights 3 and go out a The brake will be released as soon as few seconds after the engine has been the vehicle starts and accelerates. switched off. Note: if the driver’s door is opened, in- Manual operation dicator lights 3 and...
  • Page 89 ELECTRONIC PARKING BRAKE (2/4) Parking without applying the Brief stop parking brake To manually activate the electronic (if there is a risk of ice etc.): parking brake, (when stopping at a red light, or stopping when the engine is – Stop the engine by pressing the running, etc.): pull and release switch 2.
  • Page 90 ELECTRONIC PARKING BRAKE (3/4) versions with an automatic Operating faults gearbox © Indicator light flashes, accom- When indicator lights and in cer- ® panied by indicator lights For safety reasons, automatic release © tain cases light up on the instru- and the message “Parking is deactivated when the driver’s door ment panel accompanied by the mes-...
  • Page 91: Emergency Unlocking

    This control cannot be used to reap- and contact an approved Dealer. cle with the RENAULT card ply the parking brake. A reminder can be found on the inside. They could acci- label in area A.
  • Page 92: Engine Adjustments

    ADvICE: antipollution, fuel economy and driving (1/3) Aiding fuel economy Your vehicle complies with criteria for Have your vehicle adjusted and recycling and recovering vehicles at the checked by an approved Dealer, in ac- Depending on the vehicle, in order to end of their service life which will come cordance with the instructions given in optimise consumption, an indicator light...
  • Page 93 ADvICE: antipollution, fuel economy and driving (2/3) Exhaust gas monitoring – Sporty driving uses a lot of fuel: drive with a light right foot. system – Brake as little as possible. If you an- The exhaust gas monitoring system will ticipate an obstacle or bend in ad- detect any operating faults in the vehi- vance, you may then simply release...
  • Page 94 ADvICE: antipollution, fuel economy and driving (3/3) – In vehicles fitted with air condi- tioning, it is normal to observe an increase in fuel consumption (es- pecially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
  • Page 95: Environment

    This commitment is illustrated by the lation. less fuel (eg. 140 g/km, equivalent to Renault eco² group signature. 5.3 l/100 km for a diesel vehicle). Recycling Our vehicles are also equipped with a...
  • Page 96: Tyre Pressure Monitor

    TYRE PRESSURE MONITOR (1/3) This system monitors the tyre pressure. The pressures must be adjusted when the tyres are cold. If the tyre pressures cannot be checked The operation of the tyre pressure when the tyres are cold, assume an in- monitor may be affected by using crease of 0.2 to 0.3 bar (or 3 PSI).
  • Page 97 TYRE PRESSURE MONITOR (2/3) Changing a wheel Emergency spare wheel The tyre pressure monitor takes ap- The emergency spare wheel has no proximately 8 minutes to identify the sensor, and cannot be recognised by tyres which have been replaced. The the system.
  • Page 98 TYRE PRESSURE MONITOR (3/3) Examples of messages which may appear on the instrument panel displays Message Display Interpretation of messages “Adjust tyre The tyre pressure is lower than normal. pressure” ® Indicator light comes on, accompanied by a bleep. Stop the vehicle as soon as “Underinflation possible and contact an approved dealer.
  • Page 99 ALL-wHEEL DRIvE SYSTEM: 4 wheel drive (4wD) (1/3) “AUTO” mode “4wD Lock” mode This is the mode defined each time Press the bottom section of button 1. the engine is started. The button returns immediately to its ’ original position. The indica- Operating principle tor light will light up on the instrument...
  • Page 100: Drive System

    ALL-wHEEL DRIvE SYSTEM: 4 wheel drive (4wD) (2/3) Operating faults When the system detects an operating fault the message “Check 4WD” and © warning light appear on the in- – as soon as the vehicle speed ex- strument panel. ceeds 24 mph (40 km/h) in “4WD Contact your approved Dealer as soon Lock”...
  • Page 101 ALL-wHEEL DRIvE SYSTEM: 4 wheel drive (4wD) (3/3) All-wheel drive system – Depending on the driving conditions, the system may switch automatically from “2WD” to “4WD”. In this case, the “4WD” indicator light does not come on. – Whichever mode is selected, do not start the engine if the rear wheels are on the ground and the front wheels are in the air (e.g.
  • Page 102: Driver Correction Devices

    DRIvER CORRECTION DEvICES (1/5) ABS (anti-lock braking Operating faults: Depending on the vehicle, this is com- posed of: – If the message “Check ABS” is dis- system) – the anti-lock braking system ABS; © Under heavy braking, the ABS prevents played and the –...
  • Page 103: Electronic Stability Control

    DRIvER CORRECTION DEvICES (2/5) Electronic stability control Operating faults Traction control ASR ESC with understeer control This system helps to limit wheelspin of When the system detects an operat- and traction control ASR the drive wheels and to control the ve- ing fault the message “Check ESC”...
  • Page 104: Emergency Brake Assist

    DRIvER CORRECTION DEvICES (3/5) If you deactivate this function, the Emergency brake assist traction control (ASR) system will This system supplements the ABS also be deactivated. and helps reduce vehicle stopping dis- As the ESC and ASR provide enhanced tances. safety, it is not advisable to drive with the function switched off.
  • Page 105: Hill Descent Control

    DRIvER CORRECTION DEvICES (4/5) Starting the system The hill descent control system is de- With the vehicle travelling downhill at activated as soon as you depress the less than 15 mph (25 km/h) in first or re- brake pedal or the accelerator pedal, verse gear (position D or R for vehicles and reactivated as soon as you release with an automatic transmission), press...
  • Page 106 DRIvER CORRECTION DEvICES (5/5) Hill start assistance This function assists the driver when starting on hills. It prevents the vehicle The hill start assistance from rolling backwards, depending on system cannot completely the slope, by automatically applying the prevent the vehicle from brakes when the driver lifts his/her foot rolling backwards in all sit- off the brake pedal to depress the ac-...
  • Page 107: Speed Limiter

    CRUISE CONTROL, SPEED LIMITER: speed limiter function (1/3) Controls Switching on The speed limiter function helps you stay within the driving speed limit that  1 Main “On/Off” switch. Press switch 1 on the side showing you choose, known as the limit speed. Indicator light 6 comes on, lit orange, 2 Limit speed activation, storage and and the message “Speed limiter”...
  • Page 108 CRUISE CONTROL, SPEED LIMITER: speed limiter function (2/3) varying the limit speed Exceeding the limit speed To vary the limit speed, press switch 2 It is possible to exceed the limit speed (+) repeatedly to increase the speed or at any moment. To do this: press the switch 5 (-) to decrease.
  • Page 109 CRUISE CONTROL, SPEED LIMITER: speed limiter function (3/3) Recalling the limit speed If a speed has been stored, it can be re- called by pressing switch 3 (R). Putting the function on Switching off the function standby The speed limiter function is deacti- vated if you press switch 1: in this case The speed limiter function is suspended a speed is no longer stored.
  • Page 110 CRUISE CONTROL, SPEED LIMITER: cruise control function (1/4) The system is designed in such a way that it is possible to detect a dif- ference between the programmed speed and the speed shown on the instrument panel. This function is an addi- tional driving aid.
  • Page 111: Cruise Control

    CRUISE CONTROL, SPEED LIMITER: cruise control function (2/4) Switching on Activating cruise control Driving  At a steady speed (above approxi- Once a cruising speed is stored and Press switch 1 on the side showing mately 20 mph (30 km/h)) press the cruise control function is active, Indicator light 7 comes on, lit green, switch 2 (+) or 5 (-): the function is acti-...
  • Page 112 CRUISE CONTROL, SPEED LIMITER: cruise control function (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While it is being exceeded, the cruising speed flashes on the in- strument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
  • Page 113 CRUISE CONTROL, SPEED LIMITER: cruise control function (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road condi- tions are suitable (traffic, road surface, weather conditions, etc.). With a ve- hicle speed above 20 mph (30 km/h), press switch 3 (R).
  • Page 114 PARKING DISTANCE CONTROL (1/3) Operating principle Front parking distance control On equipped vehicles, ultrasonic sen- (Depending on the vehicle) sors fitted in the vehicle’s rear and/or front bumper measure the distance Operation between the vehicle and an obstacle when moving forwards at less than when reversing.
  • Page 115: Parking Distance Control

    PARKING DISTANCE CONTROL (2/3) Automatic activation/deactivation of If there are obstacles located close to both the front and rear of the vehicle, rear parking distance control only the closest of the two will be ac- The system deactivates: knowledged and the corresponding –...
  • Page 116 PARKING DISTANCE CONTROL (3/3) Activating/deactivating for long periods Press the switch for approximately 3 seconds to deactivate the system: the indicator light on the switch comes on and the message “Parking sensor off” is displayed on the instrument panel. The system is reactivated by press- ing the switch again for approximately 3 seconds.
  • Page 117: Selector Lever

    AUTOMATIC OR CONTINUOUSLY vARIABLE TRANSMISSION (1/3) Driving in automatic mode Select position D. In most traffic con- ditions, you will not have to touch the gear selector lever again: the gears will change automatically at the right time and at the most suitable engine speed because the automatic system takes into account the vehicle load and road contour and adjusts itself to the particu-...
  • Page 118: Parking The Vehicle

    AUTOMATIC OR CONTINUOUSLY vARIABLE TRANSMISSION (2/3) Driving in manual mode Special circumstances Parking the vehicle With the selector lever in position D, – If the bends and road surface do When the vehicle is stopped, move the move the lever to the left. Shifting the not allow you to stay in automatic lever to position P while keeping your lever repeatedly allows you to change...
  • Page 119 AUTOMATIC OR CONTINUOUSLY vARIABLE TRANSMISSION (3/3) Operating faults – when driving, if the “Check auto gearbox” message appears on the instrument panel, it indicates a fault. Contact your approved Dealer as soon as possible. – when driving, if the message “Auto gearbox overheating”...
  • Page 120 2.42...
  • Page 121: Your Comfort

    Section 3: Your comfort Air vents (air outlets) ............. Manual air conditioning/heating system .
  • Page 122: Air Vents, Air Outlets

    AIR VENTS, air outlets (1/2) 6 right-hand side window demisting 1 left-hand side air vent vent 2 left-hand side window demisting 7 right-hand side air vent vent 8 passenger footwell air vents 3 windscreen demisting vents 9 driver footwell air vents 4 Centre air vents.
  • Page 123 AIR VENTS, air outlets (2/2) Air flow Direction To remove bad odours from your ve- hicles, only use the systems designed Turn the control knobs 2 to adjust the Move tabs 1 or 3. for this purpose. Consult an approved flow of air.
  • Page 124: Air Recirculation Mode

    MANuAl AIR coNDITIoNINg/hEATINg SySTEM (1/3) Air recirculation mode Press the button B: the indicator light on the button comes on. In these conditions air is taken from the passenger compartment and is recircu- lated, with no air being taken from out- side the vehicle.
  • Page 125: Adjusting The Ventilation Speed

    MANuAl AIR coNDITIoNINg/hEATINg SySTEM (2/3) Switching air conditioning on or off The air conditioning is switched on (in- dicator light illuminated) or off (indicator light extinguished) using button F. The air conditioning system is used for: – lowering the temperature inside the passenger compartment;...
  • Page 126 MANuAl AIR coNDITIoNINg/hEATINg SySTEM (3/3) Rear screen de-icing/ demisting Press button D: the indicator light on the button comes on. This function is used to prevent con- densation forming on the rear screen. To switch it off, press button D again. “clear View”...
  • Page 127: Automatic Climate Control

    AuToMATIc clIMATE coNTRol (1/6) Adjusting the air temperature – Turn control 1 to adjust the tempera- ture on the driver’s side: the temper- ature is displayed on screen 2; – Turn control 9 to adjust the tem- perature on the passenger’s side: the temperature is displayed on screen 10.
  • Page 128: Automatic Mode

    AuToMATIc clIMATE coNTRol (2/6) Automatic mode To reach and keep the chosen comfort level and to maintain good visibility, the Press the automatic mode button 3. system controls: The indicator light on the button comes – ventilation speed; – air distribution; The automatic climate control system ensures, in most cases, a comfortable –...
  • Page 129 AuToMATIc clIMATE coNTRol (3/6) The displayed temperature values show a comfort level. When the vehicle is started in cold or hot weather, increasing or de- creasing the values displayed does not mean that the temperature is Varying the ventilation speed Switching air conditioning on reached more quickly.
  • Page 130 AuToMATIc clIMATE coNTRol (4/6) “clear View” function Press button 8: the integrated indicator light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
  • Page 131 AuToMATIc clIMATE coNTRol (5/6) The air flow is mainly directed to the dashboard vents. The air flow is directed to the windscreen demisting vents and the dashboard vents. This setting maintains the optimum temperature level in warm weather. The air flow is directed to the windscreen demisting vents õ...
  • Page 132 AuToMATIc clIMATE coNTRol (6/6) 14 15 Setting the air recirculation Flow of air from rear air Prolonged use of this position may lead to odours, caused by non-renewal of mode vents. air, and the formation of condensation (depending on vehicle) Pressing button 11 activates air recircu- on the windows.
  • Page 133: Maintenance

    AIR coNDITIoNINg: information and advice on use Advice on use operating faults In some situations, (air conditioning Fuel consumption off, air recirculation activated, venti- As a general rule, contact your ap- lation speed at zero or low, etc.) you proved dealer in the event of an op- You will normally notice an increase may notice that condensation starts erating fault.
  • Page 134: Electric Windows

    Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave a Front and rear passenger with the ignition on, press the switch child (or a pet) unsupervised, even...
  • Page 135 – Fully and briefly press down on the then lower and raise the window fully to the RENAulT card or, in hands-free relevant switch down: the window reinitialise the system. mode, the door or tailgate button, will open completely.
  • Page 136: Electric Sunroof

    (limited to approximately 45 sec- onds). Driver’s responsibility Never leave your vehicle with the RENAULT card inside and never leave a Sunroof blind Tilting the sunroof child (or a pet) unsupervised, even opening: open the sunroof blind, then Move handles 1 forwards or backwards for a short period of time.
  • Page 137: Remote Control

    When you lock the doors from the out- using products recommended by our side, press the locking button on Technical Department; the RENAulT card or, in hands-free – do not open the sunroof immedi- mode, the door or tailgate button ately after the vehicle has been in...
  • Page 138: Sun Visor

    SuN VISoR Front sun visor courtesy mirror with light Lower the sun visor 1 over the wind- Lift the cover 4. screen or unclip it and turn it over the Light 5 switches on automatically. side window. courtesy mirror without light 3 Lift cover 2.
  • Page 139: Child Minder Mirror

    SuN VISoR/chIlD MINDER MIRRoR Side sun blind child minder mirror (depending on vehicle) Pull the sun visor upwards using tab 6 until hooks 7 engage in their hous- This allows you to see the rear seats. ing (make sure the hooks are properly –...
  • Page 140: Interior Lighting

    INTERIoR lIghTINg (1/2) courtesy lights Door lights glove box light 5 Use switch 3: Each light 4 comes on when a door is Light 5 comes on when the cover is – left-hand side: the light comes on opened. opened. when a door is opened.
  • Page 141: Luggage Compartment Light

    INTERIoR lIghTINg (2/2) Rear light 7 luggage compartment light 9 Use switch 6: Use switch 8: – top position: the light is off; – top and bottom positions: light off; – central position: the light comes – central position: the light comes on when a door is opened.
  • Page 142: Passenger Compartment Storage/Fittings

    PASSENgER coMPARTMENT SToRAgE, FITTINgS (1/6) Passenger storage Front door armrest storage 6 Depending on the vehicle, this storage compartment has: compartment Pull handle 1 to open it. – a card holder 2 Door pockets 7 It can hold A4 size documents, large It can hold books, maps, cups, etc.
  • Page 143 PASSENgER coMPARTMENT SToRAgE, FITTINgS (2/6) Sunglasses holder 8 Mobile phone storage Front centre armrest storage compartment and ashtray 10 compartment A (depending on vehicle) Lift control 13 then lift cover 12. Sun visor storage 9 Note: do not use this storage compart- This can be used for storing motorway ment for bottles or cups.
  • Page 144: Cup Holder

    PASSENgER coMPARTMENT SToRAgE, FITTINgS (3/6) Rear armrest storage 16 Ski hatch Removing the rear armrest Depending on the vehicle, a storage If you want to transport long objects Pull strap 21 to unclip it. compartment may be fitted in the rear (skis etc.) in the luggage compartment, Press on the left-hand side of the arm- armrest.
  • Page 145 PASSENgER coMPARTMENT SToRAgE, FITTINgS (4/6) handle for holding bags Rear parcel shelves 24 Rear door storage (depending on vehicle) whilst cornering 22 compartment 27 Raise it to the horizontal position. This offers support and can be held This can be used to store books, drinks when the vehicle is moving.
  • Page 146 PASSENgER coMPARTMENT SToRAgE, FITTINgS (5/6) Drawer under passenger Passenger compartment floor luggage compartment floor seat 29 storage 30 storage 32 (depending on vehicle) Hold handle 28 and pull out drawer 29. There is a flap 32 on both sides of the A flap 30 is located either side of the luggage compartment.
  • Page 147 PASSENgER coMPARTMENT SToRAgE, FITTINgS (6/6) Storage compartment under Lift the handle then attach the hook 35 Depending on the vehicle, these stor- to the ring 36. age compartments are available 37. the luggage compartment carpet. Lift the luggage compartment carpet with handle 34.
  • Page 148: Cigar Lighter

    AShTRAy/cIgAR lIghTER/AccESSoRIES SocKET Ashtray 1 Accessories socket 4 and 5 (depending on vehicle) This is a removable ashtray which may be fitted into one of the cup holders or Depending on the vehicle, this can be storage compartments 3 in the vehicle. fitted instead of cigar lighter 2.
  • Page 149: Rear Headrests

    REAR hEADRESTS Position for use To remove the headrest Raise or lower the headrest while pull- Press tabs 1 and 2 simultaneously and ing it towards the front of the vehicle. remove the headrest. Storage position A To refit the headrest Press tab 1 or 2 and lower the headrest Slide the headrest rods into the holes, completely.
  • Page 150: Rear Bench Seat Functions

    REAR BENch SEAT FuNcTIoNS (1/2) To fold down the rear To fold down the rear seats To return the seat to its seats from the luggage from inside the passenger original position compartment compartment – lift the seatback and return it to its original position;...
  • Page 151: Rear Seat

    REAR BENch SEAT FuNcTIoNS (2/2) When adjusting the seat, always ensure that the seat belt can return to its original position. When moving the rear bench seat, make sure the bench seat anchor- age points are clean (they should be To adjust the seatback on the free from grit, cloths etc.).
  • Page 152: Luggage Compartment

    luggAgE coMPARTMENT (1/2) Max 200 Kg Double opening tailgate Full access: when the upper section is open, pull handle 2 and guide the lower opening section B fully downwards. The maximum authorised Quick access: press switch 1 and lift weight on the lower sec- the upper section A.
  • Page 153 luggAgE coMPARTMENT (2/2) To close the tailgate opening the tailgate from Next, lower the upper section A and close it. inside the vehicle Lift the lower section B of the tailgate, For your comfort, use handle 3 on the then close it. If the tailgate cannot be opened from tailgate to close it.
  • Page 154: Luggage Cover

    luggAgE coMPARTMENT coVER (DEPENDINg oN ThE VEhIclE) To unfold the flexible section Removing the luggage cover luggage compartment cover of the luggage compartment storage Press the two ends 3 and move them cover towards the centre of the luggage com- Move the parcel shelf up (move- partment cover, then tilt the cover.
  • Page 155 TRANSPoRTINg oBjEcTS IN ThE luggAgE coMPARTMENT/TowINg (towing equipment) Always place the objects to be trans- ported so that their largest side rests against the back of the rear bench seat, for normal loads (example A), or Always position the heavi- against the back of the front seats when est items directly on the the rear bench seatbacks are folded...
  • Page 156: Anchorage Points/Luggage Net

    ANchoRAgE PoINTS/luggAgE NET Anchorage points 1 luggage net The luggage net can be attached using anchorage points 1, 2 and 3. Always position the heavi- est items directly on the floor. If the vehicle is equipped with anchorage points 1 on the luggage compart- It is prohibited to attach a ment floor, use them.
  • Page 157: Roof Bars

    RooF BARS It is strictly forbidden to place the roof bars in the transverse position Roof bars 1 Roof bar mounting points 2 (carrying position) when entering a (depending on vehicle) roller-type car wash. To access the mounting points, pivot Luggage can be transported on the lug- each section 2 upwards using a flatb- gage bars mounted on the roof bars.
  • Page 158: Multimedia Equipment

    MulTIMEDIA EQuIPMENT The presence and location of this equipment depends on the vehicle’s multimedia equipment. 1 Radio; 2 central control; 3 steering column control; 4 microphones; 5 multimedia sockets. hands-free telephone integrated control On equipped vehicles, use micro- phones 4 and steering column con- trol 3.
  • Page 159 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
  • Page 160: Bonnet

    BOnnet Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet, replace stay 2 back into its holder 3, hold the bonnet in the middle and lower it to 30 cm above the closed position, then release it. It will latch automatically under its own weight.
  • Page 161: Engine Oil Level: General Information

    enGIne OIL LeVeL: general information (1/2) It is normal for an engine to use oil for lubrication and cooling of moving parts and it is normal to top up the level be- tween oil changes. However, contact an approved Dealer if more than 0.5 litres is being consumed every 600 miles (1,000 km) after the running in period.
  • Page 162 enGIne OIL LeVeL: general information (2/2) Once the operation is complete, ensure that the dipstick is fully inserted, or Consult your approved Dealer at the cap-type dipstick screwed in com- once if you notice an abnormal or pletely. repeated drop in any of the fluid levels.
  • Page 163: Engine Oil Level: Topping Up/Filling

    enGIne OIL LeVeL: topping up/filling (1/2) 2.5 16V 2.0 dCi topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
  • Page 164 enGIne OIL LeVeL: topping up/filling (2/2) Oil change Filling: take care when Service interval: refer topping up the oil that Maintenance Service Booklet for your no oil drips onto engine vehicle. components - risk of fire. Remember to refit the cap securely Average capacities for oil change as there is a risk of fire if oil splashes including oil filter...
  • Page 165: Levels

    LeVeLS (1/3) Checking intervals Replacement intervals Check the coolant level regularly Refer to the Maintenance Service (very severe damage is likely to be Booklet for your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
  • Page 166: Brake Fluid Level

    LeVeLS (2/3) Level 2 topping up It is normal for the level to drop as After any operation on the hydraulic cir- the linings become worn, but it should cuit, a specialist must replace the fluid. never drop below the “MIn” warning Only use fluids approved by our line.
  • Page 167: Windscreen/Headlight Washer Reservoir

    LeVeLS /FILteRS (3/3) Filters Liquid Screen wash product (product with an- The replacement of filter elements (air tifreeze in winter). filter, passenger compartment filter, diesel filter, etc.) is scheduled in the Jets maintenance operations for your vehi- cle. Use a tool such as a needle to adjust the height of the windscreen washer Replacement intervals for filter el- jets.
  • Page 168: Tyre Pressure

    tyRe pReSSuRe tyre safety and use of snow chains The tyre pressure is indicated on the Zone B: dimension of the tyres fitted to label A affixed to the edge of driver’s the vehicle. Refer to the information on “Tyres” door.
  • Page 169: Battery

    BAtteRy Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. The battery does not require any main- Label A tenance. Observe the indications on the battery: – 1 naked flames and smoking are for- bidden;...
  • Page 170: Bodywork Maintenance

    BODyWORk MAIntenAnCe (1/2) – minor impacts A well-maintained vehicle will last – Allow rust to form following minor im- longer. It is therefore recommended to pacts. You should take a minimum number of maintain the exterior of the vehicle reg- precautions in order to safeguard your –...
  • Page 171 BODyWORk MAIntenAnCe (2/2) you should – Wash your car frequently, with the – Before going through a roller type car engine off, with cleaning products wash, return the windscreen wiper – Observe the vehicle stopping dis- recommended by our Technical stalk to the Park position (refer to tances when driving on gravelled Department (never use abrasive...
  • Page 172: Interior Trim Maintenance

    InteRIOR tRIM MAIntenAnCe (1/2) Glass instrument panel textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g. instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, etc.) larly.
  • Page 173 InteRIOR tRIM MAIntenAnCe (2/2) Removal/replacing removable you should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
  • Page 174 4.16...
  • Page 175: Practical Advice

    RENAULT card: battery ........
  • Page 176: Emergency Spare Wheel 6

    Puncture, emergency sPare wheel Vehicles fitted with an emergency spare wheel smaller than the four other wheels: – Never fit more than one emer- gency spare wheel to the same vehicle. – Replace the emergency spare wheel as soon as possible with a wheel with the same dimensions as the original.
  • Page 177: Tool Kit

    tOOl KIt Jack 1 Fold the jack away correctly before storing it in its housing. Jack handle 2 towing hitch 3 Refer to the information on “Towing” in Section 5. wheelbrace 4 Allows the wheel bolts to be locked/un- locked. note: depending on the vehicle, tools 2 and 4 are stored in a bag.
  • Page 178: Changing A Wheel

    changIng a wheel (1/2) Attach the wheelbrace 1 and the jack handle 6 (in groove 5). Turn the wheelbrace until the wheel lifts off the ground. Vehicles equipped with Switch on the hazard warn- jack, wheelbrace and wheel ing lights. wrench Keep the vehicle away from Use the wheelbrace 1 to slacken off...
  • Page 179 changIng a wheel (2/2) Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub. If bolts are supplied with the emergency spare wheel, only use these bolts for the emergency spare wheel.
  • Page 180: Tyres (Tyre And Wheel Safety, Use In Winter)

    tyres (1/3) tyre and wheel safety When the tyre tread has been worn to the level of the wear indicators, they The tyres are the only contact between become visible 2: it is then neces- the vehicle and the road, so it is essen- sary to replace your tyres because the tial to keep them in good condition.
  • Page 181: Tyre Pressures

    tyres (2/3) tyre pressures emergency spare wheel Pressures should be checked when the tyres are cold; ignore higher pressures Adhere to the tyre pressures (including Refer to the information on the which may be reached in hot weather the emergency spare wheel). The tyre “Emergency spare wheel”...
  • Page 182 tyres (3/3) Fitting new tyres use in winter studded tyres This type of equipment may only be Always ensure tyres with identi- chains used for a limited period and as laid cal specifications are fitted to all four For safety reasons, fitting snow down by local legislation.
  • Page 183: Headlights (Changing Bulbs)

    halOgen heaDlIghts: changing bulbs Direction indicator lights Undo bulb holder 1 a quarter of a turn. Undo the bulb a quarter of a turn. Bulb type: wy21w. Front side light Disconnect the bulb holder 3 then remove the bulb. Bulb type: w5w. Dipped beam/main beam However, because the protective covers need to be removed, you are...
  • Page 184 XenOn heaDlIghts: changing bulbs cleaning the headlights As the headlights are made of plastic glass, use a soft cloth or cotton wool to clean them. If this does not clean it properly, moisten the cloth with soapy water, then wipe clean with a soft damp cloth or cotton wool.
  • Page 185 heaDlIghts: additional/front fog lights additional lights If you wish to fit fog lights or long range headlights to your vehicle, consult an approved dealer. Front fog lights 1 changing a bulb: Contact an approved dealer. Any operation on (or modi- fication to) the electrical system must be performed by an approved dealer...
  • Page 186: Rear Lights And Side Lights: Changing Bulbs

    rear lIghts anD sIDe lIghts: changing bulbs (1/3) However, because bodywork compo- nents need to be removed, you are ad- vised to have your bulbs replaced by an approved dealer. removing the bulbs Release the light unit by pulling it back- wards.
  • Page 187: Reversing Light

    rear lIghts anD sIDe lIghts: changing bulbs (2/3) side lights and tailgate high-level brake light 10 Undo bulb holder 8 or 9 a quarter of a turn then replace the bulb. reversing light Consult an approved Dealer. note: Ensure that the lead is in place Remove the screws 7 on the tailgate before inserting the light unit.
  • Page 188 rear lIghts anD sIDe lIghts: changing bulbs (3/3) number plate lights 13 high-level indicator lights 14 Remove the two screws 12 then unclip Consult an approved Dealer. the light. Unclip the lens (using a flat-blade screwdriver or similar). Remove the bulb. Bulb type: w5w.
  • Page 189: Interior Lights (Changing Bulbs)

    InterIOr lIghtIng: changing bulbs (1/3) Vanity mirror light courtesy light Remove the bulb 3. Bulb type: c5w festoon bulb. Use a flat-blade screwdriver or similar Use a flat-blade screwdriver or similar to unclip the lens 1. to unclip the lens 2. Remove the bulb.
  • Page 190: Interior Lighting: Changing Bulbs

    InterIOr lIghtIng: changing bulbs (2/3) Passenger storage Door lights compartment light 4 Unclip light 5 (using a flat-blade screw- driver or similar). Unclip the lens then Consult an approved Dealer. remove the bulb. Bulb type: w5w. The bulbs are under pres- sure and can break when replaced.
  • Page 191 InterIOr lIghtIng: changing bulbs (3/3) rear passenger lights 6 Remove the screw 8 (using a tool such as a flat-blade screwdriver) then unclip and light for luggage the lens. Remove the bulb 9. compartment 7 Bulb type: c5w festoon bulb. Unclip light 6 or 7 (using a flat-blade screwdriver or similar).
  • Page 192: Fuses

    Fuses (1/2) INCORRECT CORRECT Fuse box 1 Disconnect the fuse using tweezers 2. Slide the fuse backwards to remove it If any electrical component does not from the tweezers. work, check the condition of the fuses. Do not reuse the fuse. Open the cover.
  • Page 193 Fuses (2/2) allocation of fuses (DePenDIng On the eQuIPment leVel) symbol allocation symbol allocation SPARE Spare fuses ELEC IGN Electrical equipment BLOWER All-wheel drive trans- Ventilation MOTOR CONT mission REAR Heated rear screen METER Counter DEFOG ROOM BOSE AMP Audio system Interior light LAMP FRONT...
  • Page 194: Battery: Troubleshooting

    Battery: troubleshooting (1/2) to avoid all risk of sparks – Ensure that any electrical consumers (courtesy lights, etc.) are switched off before disconnecting or recon- necting the battery. – When charging, stop the charger before connecting or disconnecting the battery. –...
  • Page 195: Connecting A Battery Charger

    Battery: troubleshooting (2/2) starting the vehicle using the Attach the positive lead A to the (+) ter- minal 1 then to the (+) terminal 4 of battery from another vehicle the battery supplying the current. If you have to use the battery from an- Connect the negative cable B to the (–) other vehicle to start, obtain suitable terminal 3 of the battery supplying the...
  • Page 196: Renault Card: Battery

    (insert the the next time the vehicle is started, the replace the RENAULT card battery, RENAULT card in the card reader) and message will disappear. press button 1, pulling on emergency lock/unlock the vehicle (refer to the in- note: it is not advisable to touch the key 2, then unclip cover 3 using tab 4.
  • Page 197: Accessories

    accessOrIes Before fitting an electrical or If you are using an anti-theft electronic device (particu- device, only attach it to the larly for transmitters/receiv- brake pedal. ers: frequency bandwidth, power level, position of the aerial etc.), ensure that it is compatible with your vehicle.
  • Page 198: Wiper Blades

    wIPer BlaDes Check the condition of the wiper blades. You are responsible for their service life: – clean the blades, windscreen and rear screen regularly with soapy water; – do not use them when the wind- screen or rear screen are dry; –...
  • Page 199: Towing Procedure

    (risk of running ing column is not locked. down the battery). If it is locked, insert the RENAULT card Furthermore, it is essential to respect into the reader and press the Start/Stop the towing regulations set out in the leg-...
  • Page 200: Towing: Breakdown

    tOwIng: breakdown (2/4) 2wD vehicles Vehicles fitted with an automatic If the lever is stuck in P, transmission or continuously vari- even though you are de- able transmission. pressing the brake pedal, the lever can be released with the ignition off, the gearbox is no longer lubricated.
  • Page 201 tOwIng: breakdown (3/4) 4wD vehicles Whichever type of gearbox is fitted, a 4WD vehicle must never be towed if any of its 4 wheels are touching the ground. vehicle must never be towed if one of its 4 wheels is touching the ground.
  • Page 202 (4/4) – RENAULT recommends the use of a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed must be able to brake. – A vehicle must not be towed if it is not fit to be driven.
  • Page 203 Dealer as soon as possible. using the renault card POssIBle causes what tO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the information on “Locking/unlocking the...
  • Page 204: Operating Faults

    Starting conditions are not Refer to the information on “Starting/stopping the fulfilled. engine” in Section 2. The RENAULT “hands-free” Insert the card in the card reader in order to start card does not work. the engine. Refer to the information on “Starting/stopping the engine”...
  • Page 205 OPeratIng Faults (3/5) On the road POssIBle causes what tO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
  • Page 206 OPeratIng Faults (4/5) On the road POssIBle causes what tO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.
  • Page 207 OPeratIng Faults (5/5) electrical equipment POssIBle causes what tO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
  • Page 208 5.34...
  • Page 209: Technical Specifications

    Section 6: Technical specifications Vehicle identification plates ............Dimensions .
  • Page 210: Vehicle Identification Plates

    Vehicle identification plates the information shown on the ve- 6 Technical specifications of vehicle. hicle identification plate should be 7 Vehicle paint reference. quoted on all correspondence or 8 Equipment level. orders. 9 Vehicle type. 10 Trim code. Vehicle identification plate A 11 Additional equipment specifica- 1 Vehicle type and chassis number.
  • Page 211: Engine Identification Plates

    engine identification plates 2.5 16V 2.0 dCi the information on the label A or engine plate B engine plate B should be quoted This gives the engine type and number on all of your correspondence or (it may be in a different location, de- orders.
  • Page 212: Dimensions

    diMensions (in metres) 2.690 1.545 4.520 1.695 (1) 1.715 (2) 1.550 (1) without roof rack 2.120 (2) with roof rack...
  • Page 213: Engine Specifications

    engine specifications Versions 2.5 16V 2.0 dci engine type M9R Turbo (see engine number) cubic capacity (cc) 2 488 1 995 It is essential to use unleaded petrol with the octane rating stated on the label inside the fuel filler flap. If not available, Diesel for a limited time only, use unleaded fuel: type of fuel...
  • Page 214: Weights

    Weights (in kg) the weights indicated are those of a basic model without options: they will vary depending on the equipment level of your vehicle. consult an authorised dealer. Maximum permissible all-up weight (MMac) Weights indicated on the manufacturer’s plate total train weight (MtR) (refer to Section 6 “Vehicle identification plate”) found by calculating: total train weight...
  • Page 215: Replacement Parts And Repairs

    ReplaceMent paRts and RepaiRs Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
  • Page 216: Service Sheets

    seRVice sheets (1/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 217 seRVice sheets (2/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 218 seRVice sheets (3/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 219 seRVice sheets (4/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 220 seRVice sheets (5/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 221 seRVice sheets (6/6) Vin: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □ ........□ anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous type of operation: stamp Service □...
  • Page 222: Anticorrosion Check

    anticoRRosion check (1/5) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.14...
  • Page 223 anticoRRosion check (2/5) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.15...
  • Page 224 anticoRRosion check (3/5) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.16...
  • Page 225 anticoRRosion check (4/5) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.17...
  • Page 226 anticoRRosion check (5/5) If the continuation of the warranty is subject to repair, it is indicated below. Vin: ............stamp Corrosion repair operation to be carried out: Date of repair: Repair to be carried out: stamp Date of repair: Repair to be carried out: stamp Date of repair: 6.18...
  • Page 227: Alphabetical Index

    AlphAbeticAl index (1/5) ABS ...............2.24 → 2.28 catalytic converter............2.6, 2.8 accessories................ 5.23 central door locking ........1.8, 1.11 → 1.13 accessories socket ............3.28 changing a bulb ............5.9 → 5.14 additional methods of restraint .......... 1.27 changing a wheel............5.4 – 5.5 side protection .............
  • Page 228 AlphAbeticAl index (2/5) driver’s position .........1.40 – 1.41, 1.44 → 1.47 manual controls ..........1.15 – 1.16 driving ..........2.2 → 2.16, 2.18 → 2.41 front seats driving position adjustment ............1.14 → 1.16 settings ............. 1.17 – 1.18 fuel advice on fuel economy ..........2.14 capacity ............1.70 →...
  • Page 229 AlphAbeticAl index (3/5) sounding the horn ............1.62 brake lights ............5.12, 5.14 dipped beam headlights ......1.63 → 1.65, 5.9 direction indicators ........1.62, 5.9, 5.12 indicators ................5.9 fog lights ............. 1.65, 5.11 indicators: hazard warning ............1.62 exterior temperature indicator ........1.39 main beam headlights ............
  • Page 230 → 3.27 functions ............3.30 – 3.31 storage compartments ...........3.22 → 3.27 rear view mirrors ..............1.61 sun visor ................3.18 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.13 sunroof..............3.16 – 3.17 RENAULT card battery ................5.22 use ...............1.2 → 1.8 tailgate ............
  • Page 231 AlphAbeticAl index (5/5) transporting children ......1.28 – 1.29, 1.31 → 1.35 transporting objects in the luggage compartment ........3.35 luggage net ..............3.36 trip computer and warning system... 1.44 → 1.47, 1.50 → 1.59 tyre pressure..........2.18 → 2.20, 4.10, 5.7 tyre pressure monitor..........2.18 →...
  • Page 233 à999105823Rê ï ì ä RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Table of Contents