Page 1 Renault KOLEOS Vehicle user manual...
Page 2 Renault cars. Lasting protection and optimum performance for your engine – guaranteed. Whether changing the oil or simply topping up, to find the approved ELF lubricant best suited to your vehicle, ask your Renault dealer for a recommendation or consult your vehi- cle maintenance handbook.
Page 3: Driving
This handbook may also contain information about items of equipment to be introduced later in the model year. Throughout the manual, the “approved Dealer” is your RENAULT Dealer. Enjoy driving your new vehicle.
Page 5: Table Of Contents
Sections Getting to know your vehicle ....... Driving ..............Your comfort ............Maintenance ............Practical advice ............ Technical specifications ........Alphabetical index ..........
Page 7 RENAULT card: general information, use, deadlocking ........
Page 8: Key, Radio Frequency Remote Control: General Information, Use
KEY, RADIO FREQUENCY REMOTE CONTROL: general information (1/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves 1 Locks all the opening elements.
Page 9 KEY, RADIO FREQUENCY REMOTE CONTROL: general information (2/2) Radio frequency remote control operating range This varies according to the surround- ings: take care not to lock or unlock the doors by inadvertently pressing the but- tons on the remote control. Replacement and additional keys or remote controls.
Page 10: Locking The Doors
RADIO FREQUENCY REMOTE CONTROL UNIT: use Note: The remote control A can be used to lock or unlock the doors and boot. With the engine running, the ignition It is powered by a battery which must switched on and in accessories position be replaced (refer to the information on (refer to “Ignition switch: vehicles with a “Radio frequency remote control: bat-...
Page 11: Battery Life
“Keycard battery low” appears on the 3 Unlocking/locking the boot. instrument panel (refer to the informa- 4 Switching on the lighting remotely or tion on the “RENAULT card: battery” in remote engine start-up depending section 5). on the vehicle. When the battery is flat, you can still lock/unlock and start your vehi- cle.
Page 12 RENAULT CARD: general information (2/2) Advice Avoid leaving the card in hot, cold or humid areas. Do not keep the RENAULT card in Driver’s responsibility a place where it could be bent or when parking or stopping damaged accidentally, such as in a the vehicle back pocket of a garment.
Page 13 It allows locking/unlocking without input doors. on the card RENAULT when within the Also, in hot and/or sunny weather, access zone 1. please remember that the tempera- ture inside the passenger compart- Note: It is possible to deactivate the ment increases very quickly.
Page 14 “Hands-free” unlocking Remote “Hands-free” locking you have to wait approximately 3 With the RENAULT card in zone 1, With the RENAULT card on you, and seconds to be able to unlock the ve- press the button 2 on the handle of one doors and boot closed, move away hicle again.
Page 15 6, the message Keycard not detected indicates that Unlocking with the card RENAULT the card is not inside the vehicle. This Press the button 4. avoids you driving away after having...
Page 16 RENAULT CARD: usage (4/4) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves...
Page 17 In some cases, the radio frequency card to unlock the front left-hand remote control or the RENAULT card door; may not work: – to lock each of the doors manually;...
Page 18 Access key 4 integrated in the card or unlock the front left-hand door. Slide the rear casing 3 downwards Once you are inside the vehicle, put the while pressing on zone A. key back in its casing in the RENAULT card. 1.12...
Page 19 When the door is closed, all the doors and the tailgate will be locked. Unlocking the vehicle from the outside is only possible with the RENAULT card in the vehicle’s access zone or using Interior locking/unlocking The switch 6 controls the doors and the the key.
Page 20: Opening And Closing The Doors
Special feature on vehicles If the vehicle is not equipped with the opening elements (door, boot) are open equipped with a RENAULT card knob 3, pull the handle 4. or incorrectly closed. With the doors locked, press button 2...
Page 21 OPENING AND CLOSING THE DOORS (2/2) Driver’s responsibility when parking or stopping the vehicle Never leave an animal, child or adult who is not self-suffi- cient alone on your vehicle, even for a short time. They may pose a risk to themselves Vehicle with manual door locking or to others by starting the engine, activating equipment such as the...
Page 22: Automatic Locking When Driving
AUTOMATIC LOCKING WHEN DRIVING Activating/deactivating the Operating faults function If you experience an operating fault (no automatic locking, the indicator light in- To switch it on: with the vehicle at a corporated in switch 1 does not light up standstill and the engine running, press when trying to lock the doors and tail- the switch 1 until a beep sounds.
Page 23: Emergency Call
EMERGENCY CALL (1/2) If the vehicle is equipped with it, the emergency call is a system that allows the emergency services to be called automatically or manually in the event of an accident or illness, in order to reduce the time they take to arrive on the scene.
Page 24 EMERGENCY CALL (2/2) Automatic mode In the event of unintended operation, it is possible to cancel the call by press- When warning light 2 is on, this indi- ing switch 3 for 2 seconds before the cates that the automatic system is ac- call to the call centre is set up.
Page 25: Front Headrests
FRONT HEADRESTS To raise the headrest To adjust side supports B To remove the headrest Pull the headrest upwards to the de- Depending on the vehicle, sections B Raise the headrest to its highest po- sired height. Check that it is correctly can be adjusted independently to the sition (tilt the seatback backwards if locked.
Page 26 FRONT SEATS WITH MANUAL CONTROL Operating faults When an operating fault is detected, the integrated warning lights on the switch 4 for the seat concerned flash. Consult an approved dealer. To move the seat forwards or Heated seats backwards With the ignition on: Lift handle 1 to unlock.
Page 27 FRONT SEATS WITH ELECTRIC CONTROLS (1/2) To adjust the seat’s lumbar position Lower the handle 3 to increase the sup- port and lift to decrease it. For safety reasons, carry out any adjustments when the vehicle is not being Adjusting the seat squab: driven.
Page 28: Ventilated Seats
FRONT SEATS WITH ELECTRIC CONTROLS (2/2) With the ignition on: – pressing the switch 6 on the re- quired seat for the first time activates the ventilation system at maximum power. Both integrated switch warn- ing lights come on; – a second press decreases the ven- tilation to minimum power.
Page 29: Seat Belts
SEAT BELTS (1/4) Always wear your seat belt when trav- Before starting, first adjust your driv- elling in your vehicle. You must also ing position, then ask all occupants comply with the legislation of the par- to adjust their seat belts to ensure ticular country you are in.
Page 30 SEAT BELTS (2/4) Driver’s seat belt reminder ß and, depending on the vehi- cle, front passenger seat belt re- minder This lights up on the central display when starting the engine then, if the driver’s or front passenger’s seat belt (if this seat is occupied) is not fastened and the vehicle has reached approxi- mately 12 mph (20 km/h), it flashes and...
Page 31 SEAT BELTS (3/4) Adjusting the height of the Rear seat belts 8 front seat belts The belts are locked, unlocked and adjusted in the same way as the front Use button 7 to adjust the seat belt belts. height so that the shoulder strap is worn as shown previously.
Page 32 SEAT BELTS (4/4) The following information applies to the vehicle’s front and rear seat belts. – No modification may be made to the component parts of the originally fitted restraint system: seat belts, seats and their mountings. For special operations (e.g. fitting child seats), contact an authorised dealer. –...
Page 33 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (1/4) Depending on the vehicle, they are – Have the entire restraint composed of: system checked following – seat belt inertia reel pretensio- an accident. ners; – No operation whatsoe- –...
Page 34: Methods Of Restraint In Addition To The Front Seat Belts
METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (2/4) Load limiter Airbags for driver and front passenger Above a certain severity of impact, this mechanism is used to limit the force of Fitted to the driver and passenger side. the belt against the body so that it is at The presence of this equipment is in- an acceptable level.
Page 35 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (3/4) Operating faults å This warning light will light up on the instrument panel when the ignition is switched on and then go out after a few seconds. If it does not light up when the ignition is switched on, or comes on when the engine is running, there is a fault in the system.
Page 36 METHODS OF RESTRAINT IN ADDITION TO THE FRONT SEAT BELTS (4/4) All of the warnings below are given so that the air bag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused by items which may be dislodged when the air bag inflates. Warnings concerning the driver’s air bag –...
Page 37 METHODS OF RESTRAINT IN ADDITION TO THE REAR SIDE SEAT BELTS Force limiter Above a certain severity of impact, this mechanism is used to limit the force of the belt against the body so that it is at an acceptable level. –...
Page 38 SIDE PROTECTION DEVICES Side Airbags An airbag can be fitted to each front seat and the rear side seats, which are deployed on the side of the seat (door side) to protect the occupants in the case of a severe side impact. Curtain Airbags These are airbag fitted along the sides of the vehicle in the ceiling which trigger...
Page 39: Additional Methods Of Restraint
ADDITIONAL METHODS OF RESTRAINT Operating faults All of the warnings below are given so that the airbag is not obstructed in any way when it is inflated and also to prevent the risk of serious injuries caused å by items which may be dislodged when it inflates. This warning light comes on when the engine is started and then The airbag is designed to complement the action of the seat belt.
Page 40: Child Safety: General Information
CHILD SAFETY: General information (1/2) Carrying children Children, and adults, must be correctly seated and strapped in for all journeys. The children being carried in your vehi- cle are your responsibility. A child is not a miniature adult. Children are at risk of specific injuries as their muscles and bones have not yet fin- Driver’s responsibility ished growing.
Page 41 CHILD SAFETY: General information (2/2) Using a child seat The level of protection offered by the Set a good example by always fas- child seat depends on its ability to re- tening your seat belt and teaching strain your child and on its installation. your child: Incorrect installation compromises the –...
Page 42 CHILD SAFETY: choosing a child seat Rear-facing child seats Forward-facing child seats Booster cushions A baby’s head is, proportionally, heavier The child’s head and abdomen need to From 15 kg or 4 years, the child can than that of an adult and its neck is very be protected as a priority.
Page 43: Choosing A Child Seat Mounting
CHILD SAFETY: choosing a child seat mounting (1/2) There are two ways of attaching child Attachment using the ISOFIX Before using an ISOFIX seats: via the seat belt or using the system child seat that you pur- ISOFIX system. Authorised child seats ISOFIX are chased for another vehicle, standardised in accordance with cur- check that its installation is...
Page 44 CHILD SAFETY: choosing a child seat mounting (2/2) The rings are located on the rear seat-  backs and indicated by the symbol In all cases, attach the strap hook to the corresponding ring 3 and 4 and place the seat in the desired position. Pull the belt so that the back of the child seat comes into contact with the back of the vehicle seat.
Page 45: Fitting A Child Seat, General Information
CHILD SAFETY: fitting a child seat, general information (1/2) Some seats are not suitable for fitting In the front seat After installing the child seat, if neces- child seats. The diagram on the follow- sary, the seat may be advanced (so as The laws concerning children travel- ing page shows you how to attach a to leave enough space in the rear seats...
Page 46 CHILD SAFETY: fitting a child seat, general information (2/2) In the rear side seat A carrycot can be installed across the vehicle and will take up at least two seats. Position the child with their feet nearest the door. Move the front seat as far forward as possible to install a rear-facing child seat, then move back the seat in front as far as it will go, although without al-...
Page 47 CHILD SEATS: attachment by seat belt (1/3) ³ Check the status of the airbag before fitting a child seat or allowing a passenger to use the seat. Seat not suitable for fitting ² child seats. Child seat attached using the belt ¬...
Page 48 CHILD SEATS: attachment by seat belt (2/3) The table below summarises the information already shown on the diagram on the previous page, to ensure the applica- ble regulations are respected. Front passenger seat (1) (2) Rear centre Type of child seat Weight of the child Rear side seats Without airbag...
Page 49 CHILD SEATS: attachment by seat belt (3/3) X = Seat not suitable for fitting child seats of this type. U = Seat which allows a child seat with “Universal” approval to be installed using a seat belt; check that it can be fitted. (2) Raise the seat to the maximum and position it as far back as possible, tilting the seatback slightly (approximately 25°).
Page 50 CHILD SEATS: attachment using the ISOFIX system (1/3) The table below summarises the information already shown in the diagram on the following pages, to ensure the appli- cable regulations are respected. Weight of Front passenger Type of child seat Seat size ISOFIX Rear side seats Rear centre seat the child...
Page 51 CHILD SEATS: attachment using the ISOFIX system (2/3) X = Seat not suitable for fitting child seats ISOFIX. IUF/IL = On equipped vehicles, seat which allows an approved “Universal/semi-universal” or “vehicle specific” child seat to be at- tached using the ISOFIX system; check that it can be fitted. i-U = Suitable for the i-Size restraint devices in the “Universal”...
Page 52 CHILD SEATS: attachment using the ISOFIX system (3/3) Child seat fitted using the ISOFIX mounting ü Seat which allows a ISOFIX child seat to be attached. ± The rear seats are fitted with an anchorage point which allows a forward-facing ISOFIX child seat with universal approval to be attached.
Page 53: Deactivating, Activating The Front Passenger Airbag
CHILD SAFETY: deactivating, activating the front passenger air bag (1/3) Deactivating the front To deactivate the airbags: with the vehicle stopped and the ignition off, passenger airbags push and turn lock 1 to the OFF posi- (on equipped vehicles) tion. Before fitting a child seat on the front With the ignition on, you must check passenger seat you must deactivate...
Page 54 CHILD SAFETY: deactivating, activating the front passenger air bag (2/3) The markings on the dashboard and labels A on each side of passenger sun blind 3 (example: label shown above) remind you of these instructions. DANGER Since operation of the front passenger airbag is not compatible with the position of a rear-facing child seat, NEVER...
Page 55 CHILD SAFETY: deactivating, activating the front passenger air bag (3/3) Operating faults It is forbidden to fit a rear-facing child seat to the front passenger seat if the airbags activation/deactivation system is faulty. Allowing any other passenger to sit in that seat is not recommended.
Page 56: Driving Position
DRIVING POSITION: LEFT-HAND DRIVE (1/2) 12 13 1.50...
Page 57: Instrument Panel
– Instrument panel lighting dimmer, 15 Passenger Airbag location. – Tailgate opening or Lane depar- 9 Engine start/stop button (vehicle ture warning on/off (depeding on with RENAULT card). 16 Glovebox. the vehicle), – Heated steering wheel on/off, 10 Multifunction screen.
Page 58 DRIVING POSITION: RIGHT-HAND DRIVE (1/2) 11 12 1.52...
Page 59 13 Controls for on-board computer in- 20 Engine start/stop button (vehicle – activation/deactivation of the Stop formation read-out and vehicle set- with RENAULT card). and Start function. tings customisation menu. 21 Accessories socket or cigarette 5 Heating or air conditioning con- 14 Steering column stalk for wind- lighter.
Page 60 WARNING LIGHTS (1/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. In some cases, the appearance of a Left-hand direction indicator warning light is accompanied by a mes- tell-tale sage. Right-hand direction indica- Side light warning light tor tell-tale š...
Page 61 WARNING LIGHTS (2/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Brake circuit fault warning Oil pressure warning light À light It lights up when the ignition or It lights up when the ignition or the the engine is switched on and goes off engine is switched on and goes off after after a few seconds.
Page 62 WARNING LIGHTS (3/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Toxic Fume Filter System Anti-lock braking warning Ä Warning Light light It lights up when the ignition or the On vehicles which are equipped with it, engine is switched on and goes off after this light comes on when the engine is a few seconds.
Page 63 WARNING LIGHTS (4/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Rear seat belt reminder (depending Air bag warning light å on vehicle) This warning light will be dis- played on the instrument panel when ß...
Page 64 WARNING LIGHTS (5/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Speed limiter and cruise Assisted parking brake fault  ÐÏ control indicator lights light See the information on the “Speed lim- Please refer to the information on the iter”...
Page 65 WARNING LIGHTS (6/6) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Driver’s seat belt reminder ß and, depending on the vehi- cle, front passenger seat belt re- minder This lights up when the ignition is switched on, then, if the driver's or front passenger's (if this seat is occupied) seat belt is not fastened and the vehicle...
Page 66 DISPLAYS AND INDICATORS (1/2) Instrument panel A Rev counter 4 Instrument panel in miles (option to switch to km/h) (graduations x 1000) Depending on the vehicle, you can cus- Vehicles not fitted with a navigation tomise your instrument panel with the system content and colours of your choice.
Page 67: Trip Computer And Warning System
DISPLAYS AND INDICATORS (2/2) Vehicles fitted with a navigation Coolant temperature Engine oil level low warning system indicator 7 When the engine is started, the instru- On the multifunction screen, select ment panel display A alerts you when In normal use, indicator 7 should be “System”...
Page 68 TRIP COMPUTER: general information Display selection keys 2 Scroll through the following information by repeated short presses on the con- trol 2 (the display depends on the vehi- cle equipment and country): a) total mileage and trip mileage re- corder; b) journey parameters: –...
Page 69 ON-BOARD COMPUTER: general information Interpreting some of the values displayed after resetting The values showing average fuel con- sumption and average speed will become more stable and reliable the further you have travelled since the last time the Reset button was pressed. The average fuel consumption may de- crease when: –...
Page 70 ON-BOARD COMPUTER: trip settings (1/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected 101778 km 112.4 km a) Total mileage and trip mileage recorder. Average b) Journey parameters: Average fuel consumption since the last reset.
Page 71 ON-BOARD COMPUTER: trip settings (2/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected Range Estimated range with remaining fuel. The value is displayed after driving 400 metres. 541 km Distance Distance travelled since last reset.
Page 72 ON-BOARD COMPUTER: trip settings (3/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with mileage- before-service message c) Mileage before service or oil change. Mileage before service Service in With the ignition switched on, the engine not running and Service Intervals...
Page 73 ON-BOARD COMPUTER: trip settings (4/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected On-board computer with distance before next service message (cntd.) c) Mileage before service or oil change. Mileage before service Oil change in With the ignition switched on and the engine not running,...
Page 74 ON-BOARD COMPUTER: trip settings (5/5) The display of information shown below DEPENDS ON THE VEHICLE EQUIPMENT AND COUNTRY. Examples of selections Interpreting the display selected d) Reset the tyre pressure. Refer to the information on the “Tyre pressure monitor- Tyre pressure ing system”...
Page 75 TRIP COMPUTER AND WARNING SYSTEM: information messages These can help in the vehicle starting phase, or give information about a selection or a driving status. Examples of information messages are given in the following pages. Examples of messages Interpreting the display selected «...
Page 76 TRIP COMPUTER AND WARNING SYSTEM: operating fault messages © These appear with the warning light and mean that you should drive very carefully to an authorised dealer as soon as possible. If you fail to follow this recommendation, you risk damaging your vehicle. They disappear when the display selection key is pressed or after several seconds and are stored in the computer log.
Page 77 TRIP COMPUTER AND WARNING SYSTEM: warning message ® These appear with the warning light and require you to stop immediately, for your own safety, as soon as traf- fic conditions allow. Stop your engine and do not restart it. Contact an approved Dealer. Some examples of warning messages are given below.
Page 78: Vehicle Settings Customisation Menu
VEHICLE SETTINGS CUSTOMISATION MENU (1/2) Adjusting the settings (depending on the vehicle) Select the function to modify: a) unlocking the driver’s door only; b) automatic locking of the doors while driving; c) hands-free function; d) indicator audio volume; e) internal welcome sound; f) external welcome;...
Page 79: Navigation System
VEHICLE SETTINGS CUSTOMISATION MENU (2/2) Adjusting the settings (depending on the vehicle) function activated Browse using the control 4 to select the < function to adjust: function deactivated a) Language; Once a line has been selected, press the switch 3 OK to adjust the function. b) Vehicle speed unit;...
Page 80: Steering Wheel, Power-Assisted Steering
STEERING WHEEL, POWER-ASSISTED STEERING (1/2) Power-assisted steering Variable power-assisted steering The variable power assisted steering system is equipped with an electronic control system which alters the level of assistance to suit the vehicle speed. Steering is made easier during parking manoeuvres (for added comfort) while the force needed to steer increases progressively as the speed rises (for...
Page 81: Steering Wheel Heating
STEERING WHEEL, POWER-ASSISTED STEERING (2/2) Activating the function With the ignition on, press the switch 3 , the warning light integrated in the switch lights up. Deactivating the function - Automatic: The function switches off automati- cally after the regulation phase of ap- proximately 30 minutes.
Page 82: Clock And Exterior Temperature
CLOCK AND EXTERIOR TEMPERATURE External temperature indicator Special note: When the exterior temperature is - 3 °C to + 3 °C, the °C characters flash (sig- nalling a risk of ice on the road). Display 1 Vehicles fitted with a touchscreen multimedia screen, navigation aid systems, etc.
Page 83: Rear View Mirrors
From the multifunction screen, select when the vehicle is locked using the menu “Vehicle”, “User settings”, button on the RENAULT card or remote “External welcome” and activate or de- “Hands-free” locking. In this case, when activate the function (ON or OFF).
Page 84: Interior Rear View Mirror
REAR VIEW MIRRORS (2/2) Rear view mirror without lever 4 The rear-view mirror darkens automati- cally at night if you are being followed by a vehicle with its lights on. Interior rear view mirror Its position can be adjusted. Rear-view mirror with lever 4 For night driving, to avoid being dazzled by the headlights of the car behind you, flip the small lever 4 located behind the...
Page 85: Exterior Lighting And Signals
EXTERIOR LIGHTING AND SIGNALS (1/5) Dipped beam headlights Manual operation Turn ring 3 until the symbol is opposite mark 2. This indicator light on the in- strument panel comes on. Automatic operation Turn ring 3 until the AUTO symbol is op- posite mark 2: with the engine running, the dipped beam headlights switch on or off automatically depending on the...
Page 86 EXTERIOR LIGHTING AND SIGNALS (2/5) Automatic main beam Activation  Turn ring 3 until the AUTO symbol is op- headlights posite mark 2. Depending on the vehicle, this system Push stalk 1 to activate the main beam switches the main beam headlights on ...
Page 87: Daytime Running Lights
EXTERIOR LIGHTING AND SIGNALS (3/5) Daytime running lights Switching off the lights function There are two possibilities: The daytime running lights come on – manually, move ring 3 to position 0; automatically with no action on stalk 1 – automatically, the lights will go out when the engine is started, and they go when the engine is switched off, the off once the engine is switched off.
Page 88 With the engine and lights switched ing the RENAULT card or when the ve- off and the ring 3 in position 0 or hicle is unlocked. AUTO, pull the stalk 1 towards you: the...
Page 89: Front Fog Lights
EXTERIOR LIGHTING AND SIGNALS (5/5) Rear fog lights Switching off the lights Turn centre ring 5 on the stalk Turn the ring 5 again until the mark 4 until the symbol faces mark 4, then re- is opposite the symbol for the fog light lease it.
Page 90: Audible And Visual Signals
AUDIBLE AND VISUAL SIGNALS Direction indicators Move stalk 1 parallel to the steering wheel and in the direction you are going to turn it. One-touch mode When driving, it is possible that the steering wheel may not be turned suf- ficiently to return the stalk automatically to its starting position.
Page 91: Headlight Beam Adjustment
HEADLIGHT BEAM ADJUSTMENT (1/2) For manual settings Examples of positions for adjusting control A according to the load Driver alone or with front passenger or with one front passenger and two or three rear passengers Do not use On vehicles fitted with this function, control A allows you to adjust the height Driver with a full car of passengers, luggage or (load) of the beams according to the load.
Page 92 HEADLIGHT BEAM ADJUSTMENT (2/2) When driving on the left in a left- hand drive vehicle (or vice versa), you must adjust your lights tempo- rarily during your stay. Temporary adjustment for vehicles fitted with halogen headlights Open the bonnet and identify the mark- ing B next to one of the front headlight projectors.
Page 93: Windscreen Wipers
WINDSCREEN WASH, WIPE (1/6) Check the condition of the wiper blades. You are responsible for their service life: – they must remain clean: clean the blades, windscreen and rear screen regularly with soapy Vehicle fitted with intermittent Special note water; When driving the vehicle, the wiping windscreen wipers –...
Page 94 WINDSCREEN WASH, WIPE (2/6) When activating automatic wiping or when increasing sensitivity, one sweep of the blades is performed. Note: – the rain sensor is only intended as a driving aid. In the event of re- duced visibility, the driver should manually activate the wipers;...
Page 95 WINDSCREEN WASH, WIPE (3/6) Operating fault Special note In the event of a malfunction of the When driving the vehicle, the wiping automatic wiping, the wiper is set to speed slows down whenever the ve- intermittent wiping. Contact an au- hicle stops.
Page 96: Service Position
WINDSCREEN WASH, WIPE (4/6) Specific front wiper position Note: (service position) Once the wipers have been switched off, at least 1 minute after locking the This position enables the blades to be vehicle, it is possible to manually move lifted to remove them from the winds- the blades.
Page 97: Windscreen Washer
WINDSCREEN WASH, WIPE (5/6) Note: In temperatures below zero, the washer liquid risks freezing to the windscreen, thereby reducing visibility. Heat the windscreen using the demister control before cleaning. Windscreen washer With the ignition on, pull stalk 1 then release. A brief pull will trigger a single sweep of the wipers, in addition to the wind- screen washer.
Page 98: Headlight Washers
WINDSCREEN WASH, WIPE (6/6) Note: To ensure the headlight washers op- erate correctly in winter, remove snow from the jet trims and de-ice the jet trims using an aerosol de-icer. You are recommended to regularly remove dirt encrusted on the headlight glass.
Page 99: Rear Screen Wiper
REAR SCREEN WASH, WIPE (1/2) To stop the operation, pivot ring 3 again. Note: When washing using a roller type car wash, return the ring 3 on the stalk 1 to the stop position to deactivate auto- matic wiping. Follow usage recommendations. Check the condition of the wiper blades.
Page 100 REAR SCREEN WASH, WIPE (2/2) Activation/deactivation of the rear In the event of obstacles present on the screen wiper rear window (dirt, snow, etc.), the wiper (depending on the vehicle) will try to sweep away all the obstacles. If an obstacle prevents the blade from Engaging reverse gear triggers inter- moving, it can be stopped.
Page 101: Fuel Tank (Filling With Fuel)
FUEL TANK (1/3) Petrol version It is essential to use unleaded petrol. The octane rating (RON) must comply with the information given on the label on the cover A. Refer to Section 6 for information on “Engine specifications”. Diesel version Only use diesel fuel which complies with the information on the label located inside the cover A.
Page 102 FUEL TANK (2/3) Filling with fuel With the ignition off, insert the nozzle and insert it fully before turning it on to fill the fuel tank (risk of splashing). Keep the nozzle in this position through- out the entire filling operation. When the pump cuts out automatically at the end of the filling procedure, a maximum of two further filling attempts...
Page 103 Vehicles with RENAULT card thorised dealer. Persistent fuel odour With the card RENAULT in the pas- If you notice a persistent senger compartment, press the start fuel odour you should: button 4 without pressing any of the pedals.
Page 104 1.98...
Page 105 Starting, stopping the engine: vehicle with RENAULT card ....... .
Page 106: Running In
RUNNING IN Petrol version Diesel version For the first 600 miles (1,000 km), do For the first 1,000 miles (1,500 km), not exceed 78 mph (130 km/h) in the do not exceed 80 mph (130 km/h) in highest gear, or 3,000 to 3,500 rpm. the highest gear, or 2,500 rpm.
Page 107: Ignition Switch
IGNITION SWITCH: vehicle with key Ignition position 2. The ignition is switched on: Start position 3. If the engine fails to start at the first attempt, the key must be turned back before the starter can be activated again. Release the key as soon as the engine starts.
Page 108: Starting, Stopping The Engine: Vehicle With Key/Remote Control Unit
STARTING, STOPPING THE ENGINE: vehicle with key Stopping the engine Diesel versions É With the engine idling, turn the key to – Turn the ignition key to the the “Stop” position 0. “Ignition on” position 2, and hold this position until the engine pre- heating light goes off;...
Page 109: Starting, Stopping The Engine: Vehicle With Renault Card
STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (1/5) “Hands-free” starting with the tailgate open In this case, the RENAULT card should not be located in the boot, to avoid any risk of loss. Driver’s responsibility when parking or stopping...
Page 110 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (2/5) Depress the brake or clutch pedal, then place the RENAULT 3 card (logo side) in contact with the start button 2 for around 2 seconds. Press the 2 button to start the vehicle. The message goes out.
Page 111 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (3/5) If the RENAULT card is no longer in the passenger compartment or if the card When you leave your vehi- battery is low when you try to switch cle, especially if you have the engine off, the message “No key-...
Page 112 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (4/5) The remote engine start-up operates if: – the lever is in neutral for vehicles with a manual or sequential gearbox; – the lever is in position P for vehicles with an automatic gearbox;...
Page 113 STARTING, STOPPING THE ENGINE: vehicle with RENAULT CARD (5/5) Do not use the engine remote start-up function or its programming when: – the vehicle is in a garage or in a confined space. Risk of poisoning or suffocation by exhaust gas emissions.
Page 114: Stop And Start Function
STOP AND START FUNCTION (1/4) This system enables a reduced fuel For manual gearboxes: consumption and lower greenhouse – the gearbox is in neutral; gas emissions. The system is activated automatically ignition must – the clutch pedal is released. If the when the vehicle is started.
Page 115 STOP AND START FUNCTION (2/4) Preventing the standby of the Conditions for coming out of Special note: depending on the vehi- cle, if you switch off the ignition when engine the engine standby the engine is on standby, the warning In certain situations, such as a cross- For automatic gearboxes: Ä...
Page 116 Special cases for vehicles – parking distance control is in opera- tion; standby of the engine with a RENAULT card – for vehicles with automatic gear- Certain conditions prevent the system With the engine on standby (traffic jam, boxes, the gradient is steeper than from using the engine standby function, traffic lights, etc.), if the driver unfas-...
Page 117 STOP AND START FUNCTION (4/4) Special feature of the automatic The system is automatically reactivated engine re-start each time the vehicle is started (see “Stop and Start function” in Section 2). Under certain conditions, the engine can restart on its own in order to gua- rantee your safety and comfort.
Page 118: Special Features Of Petrol Versions
SPECIAL FEATURES OF PETROL VERSIONS The following operating conditions: If you notice any of the above operating faults, have the necessary repairs car- – driving for long periods when the low ried out as soon as possible by an ap- fuel level warning light is lit;...
Page 119: Special Features Of Diesel Versions
SPECIAL FEATURES OF DIESEL VERSIONS Diesel engine speed Precautions to be taken in winter Diesel engines are fitted with injection equipment which prevents the engine To avoid any faults in icy weather: speed being exceeded irrespective of – ensure that the battery is always fully the gear selected.
Page 120: Gear Lever
GEAR LEVER Selecting reverse gear The ring 2 has to be lifted up to the gear lever knob to select reverse gear. The reversing lights will come on as soon as reverse gear is selected with the ignition on. Gear lever Vehicles with manual gearbox: refer to the grid on the gear lever knob 1.
Page 121: Parking Brake
PARKING BRAKE Parking brake To release: Depress the parking brake 1 firmly. The red warning light on the instrument panel will come on if you are driving with an incorrectly released parking brake. To apply: Depress the parking brake 1 firmly. Make sure that the park- Check that the vehicle is immo- ing brake is properly re-...
Page 122: Electronic Parking Brake
ELECTRONIC PARKING BRAKE (1/3) Assisted operation Note: To indicate that the electronic parking The assisted parking brake immobilises brake is released, a beep sounds and the vehicle when stopping the engine the message “Apply parking brake” ap- (and not when the engine is on pears on the instrument panel: standby for vehicles fitted with the Stop and Start function).
Page 123: Manual Operation
ELECTRONIC PARKING BRAKE (2/3) Brief stop Special cases To manually activate the electronic To park on a slope or while towing a parking brake, (when stopping at a red trailer, for example, pull switch 1 for light, or stopping when the engine is a few seconds to gain the maximum running, etc.): pull and release switch 1.
Page 124 ELECTRONIC PARKING BRAKE (3/3) Versions with an automatic Operating faults gearbox © – If there is a fault, the warning light illuminates on the instrument For safety reasons, automatic release panel accompanied by the “Check is deactivated when the driver’s door parking brake”...
Page 125: Eco Driving
DRIVING ADVICE, ECO-DRIVING (1/5) Fuel consumption is accredited in ac- cordance with a standard regulatory method. Identical for all manufactur- ers, this enables vehicles to be com- pared with one another. Consumption in real time depends on vehicle usage conditions, the equipment fitted and the user’s driving style.
Page 126 DRIVING ADVICE, ECO-DRIVING (2/5) This indicates: – average fuel consumption; – number of miles/kilometres travelled; – number of miles/kilometres saved. This corresponds to driving without fuel consumption (deceleration and/ or foot off the accelerator pedal). An overall rating from 0 to 100 is dis- played to let you assess your eco driv- ing performance.
Page 127 DRIVING ADVICE, ECO-DRIVING ( 3/5) ECO mode Disabling the function Press switch 4. ECO mode is a function which opti-  mises fuel consumption. This acts on The warning light goes out on all power consuming elements (engine the instrument panel to confirm deac- power, switching gears for vehicles tivation.
Page 128 DRIVING ADVICE, ECO-DRIVING (4/5) – Do not overrev the engine in the in- – Bad weather, flooded roads: termediate gears. Do not drive through You should always use the highest floods if the water is gear possible. above the lower edge of –...
Page 129 DRIVING ADVICE, ECO-DRIVING (5/5) – In vehicles fitted with air conditio- ning, it is normal to observe an in- crease in fuel consumption (espe- cially in urban conditions) when it is used. For vehicles fitted with manual air conditioning, switch off the system when it is not required.
Page 130: Maintenance And Antipollution Advice
MAINTENANCE AND ANTIPOLLUTION ADVICE Maintenance Exhaust gas monitoring Your vehicle complies with criteria for recycling and recovering vehicles at the system It is important to remember that fail- end of their service life, which will come ure to respect anti-pollution regulations The exhaust gas monitoring system will into force in 2015.
Page 131: Environment
This commitment is illustrated by the lation. less fuel (eg. 140 g/km, equivalent to Renault eco² signature. 5.3 l/100 km for a diesel vehicle). Recycling Our vehicles are also equipped with a Manufacture...
Page 132: Tyre Pressure Monitoring System
TYRE PRESSURE MONITORING SYSTEM (1/3) Resetting the standard level Resetting procedure for the tyre pressures With the ignition on: – repeatedly and briefly press con- This should be done: trol 2 to select the tyre pressure dis- – when the standard tyre pressure play and the “Tyre pressure”...
Page 133 TYRE PRESSURE MONITORING SYSTEM (2/3) « Puncture » A wheel B is shown in red, the warning  light 4 comes on, the message “Puncture” appears and there is a beep. This message appears along with the ® warning light. They indicate that the affected wheel is punctured or severely underinflated.
Page 134 Because the valves are specially de- wheels have been fitted with sensors Please see the information on “Tyres” signed, only use equipment approved not recognised by Renault. in Section 5. by the approved network. Please refer Contact an approved Dealer to fit new to “Tyre inflation kit”...
Page 135 DRIVING CORRECTION DEVICES AND AIDS (1/4) ABS (anti-lock braking Depending on the vehicle, they will con- Operating faults: sist of: system) © – lit up on the in- Under heavy braking, the ABS prevents – ABS (anti-lock braking system) ; strument panel alongside mes- the wheels from locking, allowing the sages “Check ABS”, “Check braking...
Page 136: Electronic Stability Control
DRIVING CORRECTION DEVICES AND AIDS (2/4) Electronic stability control Understeer control Operating faults ESC with understeer control This system optimises the action of the When the system detects an operat- and traction control ESC in the case of pronounced under- ing fault the message “Check ESC”...
Page 137: Emergency Brake Assist
DRIVING CORRECTION DEVICES AND AIDS (3/4) The traction control system offers ad- ditional safety. It is recommended that you do not drive with the function di- sabled. Correct this as soon as pos- sible by pressing the switch 1 again. Note: The function is reactivated auto- matically when the ignition is switched on or when a speed of approximately...
Page 138 DRIVING CORRECTION DEVICES AND AIDS (4/4) Hill start assistance Depending on the gradient of the in- cline, this system assists the driver when starting on a hill. It prevents the vehicle from rolling backwards by au- tomatically applying the brakes when the driver lifts his/her foot off the brake pedal to depress the accelerator pedal.
Page 139: Transmission: 4-Wheel Drive (4Wd)
TRANSMISSION: 4-wheel drive (4WD) (1/4) Mode selector “2WD” mode Depending on the road conditions, turn- To activate this mode, turn the selec- ing the selector 1 enables the following tor 1 to the “2WD” position. The warn- modes to be selected: ‘...
Page 140 TRANSMISSION: 4-wheel drive (4WD) (2/4) “4WD Lock” mode Note: If the vehicle speed exceeds This problem may be resolved by approximately 24.8 mph (40 km/h) in changing the tyres. Always use four To activate this mode, turn selector 1 to “4WD Lock”...
Page 141 TRANSMISSION: 4-wheel drive (4WD) (3/4) Operating faults After stopping the engine, the system Electronic stability program and may take up to five minutes to cool traction control when driving off- If the system detects an operating fault, down. road it automatically switches to “2WD” If the system detects excessive wheel- When driving on soft ground (sand, mode.
Page 142 TRANSMISSION: 4-wheel drive (4WD) (4/4) All-wheel drive system – Irrespective of the mode selected, do not start the engine if one or more wheels are not in contact with the ground (eg. when the vehicle is on a jack or roller bench). –...
Page 143: Active Emergency Braking
ACTIVE EMERGENCY BRAKING (1/10) Active emergency braking The system has two types. Depending on the vehicle, one of the two systems is equipped in the vehicle. - System A; - System B. System A Operation The system only detects vehicles While driving (at speeds of between 20 If your vehicle is equipped with system driving in the same direction of traf-...
Page 144 ACTIVE EMERGENCY BRAKING (2/10) Press the switch 5 OK again to activate or deactivate the function: function activated < function deactivated  The warning light is displayed on the instrument panel when the system is deactivated. This system is reacti- vated each time the ignition is switched Conditions for non-activation of the system...
Page 145 ACTIVE EMERGENCY BRAKING (3/10) System A (continued) Active emergency braking This function is an additional driving aid. This function is not under any Operating faults circumstances intended to replace the due care and attention of the When the system detects an operating driver, who should at all times be in control of the vehicle.
Page 146 ACTIVE EMERGENCY BRAKING (4/10) Limitation of the system operation – The system will only respond to vehicles which are moving or which have been sensed as moving. – The radar area should be kept clean and free of any modifications in order to ensure the proper operation of the system.
Page 147 ACTIVE EMERGENCY BRAKING (5/10) This system can apply maximum braking to the vehicle until it is completely stationary if necessary. For safety reasons, always wear your seat belt when travelling in your vehicle and make sure that it System B is loaded so that no items can be If your vehicle is equipped with system thrown forward and hit the occu-...
Page 148 ACTIVE EMERGENCY BRAKING (6/10) System B (continued) Special features When the vehicle speed: Operation – is less than 27.9 mph (45 km/h) ap- When driving (speed between about proximately, the warning and brak- 4.34 and 99.2 mph (7 and 160 km/h)), if ing are activated at the same time;...
Page 149 ACTIVE EMERGENCY BRAKING (7/10) Press the switch 5 OK again to activate or deactivate the function: function activated < function deactivated  The warning light is displayed on the instrument panel when the system is deactivated. This system is reacti- vated each time the ignition is switched System B (continued) For vehicle not fitted with a...
Page 150 ACTIVE EMERGENCY BRAKING (8/10) Temporarily not available Operating faults System B (continued) When the system detects a tempo- When the system detects an operating Conditions for non-activation   rary unavailability, the warning fault, the warning light lights up of the system light lights up on the instrument panel on the instrument panel, with the mes- The system cannot be activated:...
Page 151 ACTIVE EMERGENCY BRAKING (9/10) Active emergency braking This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The triggering of this function may be delayed or prevented when the system detects clear signs of control of the vehicle by the driver (action on the steer- ing wheel, pedals etc.).
Page 152 ACTIVE EMERGENCY BRAKING (10/10) Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The radar-camera area on the windscreen should be kept clean and free of any modifications in order to ensure the proper operation of the system.
Page 153: Lane Departure Warning
LANE DEPARTURE WARNING (1/3) This system notifies the driver when they accidentally cross a continuous or broken line. This function uses a camera attached to the windscreen, behind the rear-view mirror. This function is a driving aid in the event of the accidental crossing of a continuous or broken line in the road.
Page 154 LANE DEPARTURE WARNING (2/3) Activation/deactivation Vehicles not fitted with a navigation Operation system With the function activated, the grey Vehicles fitted with a navigation Press the switch 3. visibility indicators 4 for the left and system right lines are displayed on the instru- From the multifunction screen 2: select ment panel.
Page 155 LANE DEPARTURE WARNING (3/3) Adjustment – repeatedly press control 6 up or down until you reach the “Lane de- Vehicles fitted with a navigation parture warning settings” menu, then system press the switch 5 OK. – Volume: adjust the alert volume to From the multifunction screen 2, select one of three levels;...
Page 156: Blind Spot Warning
BLIND SPOT WARNING (1/4) This function is an addi- tional aid which indicates other vehicles in the blind spot area. This system alerts the driver to other Special feature It can never in any case be a subs- vehicles in the detection zone A. Make sure that the sensors are not ob- titute for care nor for the driver’s scured (by dirt, mud, snow, etc.).
Page 157 BLIND SPOT WARNING (2/4) – repeatedly press control 5 up or down until you reach the “Blind spot alert” menu, then press the switch 4 – Press the switch 4 OK again to acti- vate or deactivate the function. Activation/deactivation Vehicles not fitted with a navigation system Vehicles fitted with a navigation...
Page 158 BLIND SPOT WARNING (3/4) Display B The function is activated and has not detected any vehicles. Display C Initial warning: the indicator light 6 shows that a vehicle has been detected in the blind spot. Display D When the direction indicator is activa- ted, the indicator light 6 flashes when a vehicle is detected in the blind spot on the side towards which you are about to...
Page 159 BLIND SPOT WARNING (4/4) Operating faults If the system detects a fault, the mes- sage “Check blind spot alert” is dis- played on the instrument panel. Consult an authorised dealer. Note: When the engine is started, the indicator light 6 (display B) flashes three times.
Page 160 OVERSPEED ALERT (1/3) Operating principle For vehicles equipped with a navigation system and if the vehicle is travelling in The system detects speed limit signs a country where the speed units differ on the side of the road and displays the from those of the vehicle, the system speed limit.
Page 161 OVERSPEED ALERT (2/3) – repeatedly press the control 6 up or down until you reach the Speed alert menu, then press the switch 5 OK. – press OK to turn the function on or off. Varying the limit speed If the speed limiter notification differs from the detected speed value, press and hold the switch 4: –...
Page 162 OVERSPEED ALERT (3/3) Operating fault This function is an additional driving aid. This function is not under any The system cannot detect the speed circumstances intended to replace the due care and attention of the limit if: driver, who should at all times be in control of the vehicle. –...
Page 163: Speed Limiter
SPEED LIMITER FUNCTION (1/3) Switching on  Press switch 1 on side . The indica-  tor light comes on, lit orange, and the message “Speed limiter” appears on the instrument panel, accompanied by dashes to indicate that the speed limiter function is activated and waiting to store a limited speed.
Page 164 SPEED LIMITER FUNCTION (2/3) Varying the limit speed Exceeding the limit speed The speed limiter can be changed by It is possible to exceed the limit speed repeatedly pressing the switch 2: at any time. To do this: press the accel- erator pedal firmly and fully (beyond –...
Page 165 SPEED LIMITER FUNCTION (3/3) Recalling the limit speed If a speed has been saved, it can be re- called by pressing switch 3 ((R)). Putting the function on Switching off the function standby The speed limiter function is deacti- vated if you press switch 1: in this case The speed limiter function is sus- a speed is no longer stored.
Page 166: Cruise Control
CRUISE CONTROL FUNCTION (1/4) This function is an addi- tional driving aid. However, the function does not take the place of the driver. The cruise control function helps you to Controls Therefore, it can under no circum- maintain your driving speed at a speed stances replace the driver’s respon- 1 Main “On/Off”...
Page 167 CRUISE CONTROL FUNCTION (2/4) Activating cruise control At a steady speed (above approx. 20 mph (30 km/h)), press the switch 2 on side a (+): the function is activated and the current speed is saved. The cruising speed replaces the dashes and cruise control is confirmed by the appearance of the message “Check cruise control”...
Page 168 CRUISE CONTROL FUNCTION (3/4) Exceeding the cruising speed The cruising speed may be exceeded at any time by depressing the accelera- tor pedal. While overtaking, the cruis- ing speed flashes red on the instrument panel. Then, release the accelerator: after a few seconds, the vehicle will automati- cally return to its set cruising speed.
Page 169 CRUISE CONTROL FUNCTION (4/4) Returning to the cruising speed If a speed is stored, it can be recalled, once you are sure that the road con- ditions are suitable (traffic, road sur- face, weather conditions, etc.). Press switch 3 (R) if the vehicle speed is above 20 mph (30 km/h).
Page 170: Adaptive Cruise Control
ADAPTIVE CRUISE CONTROL (1/8) The adaptive cruise control is a func- tion which gives you the option, when traffic conditions permit (large free-flow- ing road or motorway), of maintaining a chosen speed, known as the cruising speed, while keeping a safe distance from the vehicle in front in the same lane.
Page 171 ADAPTIVE CRUISE CONTROL (2/8) Controls Switching on The cruising speed replaces the dashes and cruise control is confirmed by the Press switch 5 on the side showing  5 Main “On/Off” switch. appearance of the message “Adaptive Warning light comes on, lit green, ...
Page 172 ADAPTIVE CRUISE CONTROL (3/8) Driving Varying the following distance Once a cruising speed is memorised and the cruise control function is active, You can vary the following distance you may lift your foot off the accelera- from the vehicle in front at any time by tor pedal.
Page 173 ADAPTIVE CRUISE CONTROL (4/8) Putting the function on Returning to the cruising speed standby If a speed is stored, it can be recalled, once you are sure that the road con- The function is set to standby if: ditions are suitable (traffic, road sur- –...
Page 174 ADAPTIVE CRUISE CONTROL (5/8) Under certain conditions (coming up behind a vehicle moving more slowly, rapid change of lane of vehicles in front etc.), the system may not have time to respond and may emit a beep along- side the alert A when the situation re- quires the driver’s attention, or the alert B when the situation requires im- mediate action from the driver.
Page 175 ADAPTIVE CRUISE CONTROL (6/8) Operating faults When the system detects an operating fault the message “Check cruise con- trol” appears on the instrument panel. There are two possibilities: – the system is temporarily disrupted (for example: radar obscured by dirt, mud, snow etc.).
Page 176 ADAPTIVE CRUISE CONTROL (7/8) This function is an additional driving aid. This function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. The driver should always adapt their speed to the traffic conditions, regardless of the system indications.
Page 177 ADAPTIVE CRUISE CONTROL (8/8) Limitation of the system operation – A vehicle travelling in the opposite direction will not trigger any alert or any action on the system operation. – The radar-camera should be kept clean and free of any modifications in order to ensure the proper operation of the system.
Page 178: Parking Distance Control
PARKING DISTANCE CONTROL (1/5) Operating principle Ultrasonic sensors in the rear bumper measure the distance between the ve- hicle and an obstacle. This measurement is indicated by beeps which become more frequent the closer you come to the obstacle, until they become a continuous beep when the vehicle is approximately 20 to This function is an addi-...
Page 179 PARKING DISTANCE CONTROL (2/5) Note: the display 2 shows the vehicle Operation surroundings and emits beeps. Most objects located less near the It is necessary to travel a few metres front, rear and sides of the vehicle are before the side detection is activated. detected.
Page 180 PARKING DISTANCE CONTROL (3/5) If a side obstacle is detected: – the beeps become faster and then sound continuously as the obstacle gets nearer. Green, orange and red zones will be displayed on the dis- play D; – if there is no risk of collision, no beep will sound when approaching the ob- stacle.
Page 181 PARKING DISTANCE CONTROL (4/5) System sound Enables the system sound to be se- lected from a choice of 3. Deactivating the system sound Activate or deactivate the parking dis- tance control sound. Note: If you deactivate the sound, you will no longer be notified with beeps when approaching an obstacle.
Page 182 PARKING DISTANCE CONTROL (5/5) Automatic deactivation of the Operating faults parking distance control When the system detects an operating fault, a beep sounds for approximately The system deactivates: 3 seconds each time reverse gear is se- The function can be disrupted under –...
Page 183: Reversing Camera
REVERSING CAMERA (1/2) Operation Fixed gauge 3 4 moving guide line: The fixed clearance gauge comprises This is shown in blue on the multifunc- Moving into reverse gear, the camera 1 coloured markers A, B and C, indicat- tion screen 2. It indicates the vehicle located on the tailgate provides a view ing the distance behind the vehicle: trajectory according to the position of...
Page 184 REVERSING CAMERA (2/2) You can also adjust the camera image settings (brightness, contrast, etc.) The screen shows a reverse mirror Activating, deactivating the image. This function is an additional reversing camera The frames are a representation aid. It cannot, therefore, projected onto flat ground;...
Page 185: Assisted Parking
ASSISTED PARKING (1/6) Look in all directions Select indicator This function assists with parking ma- Switching on Special features noeuvres. With the vehicle at a standstill or driving Ensure that the ultrasonic sensors indi- Take your hands off the steering wheel. at less than approximately 18.6 mph cated by arrows 3 are not obscured (by You only control the pedals and the...
Page 186 ASSISTED PARKING (2/6) Choice of manoeuvre Look in all directions Look in all directions Select indicator Reverse The system can perform four types of manoeuvres: – 4 parallel parking; – 5 perpendicular parking; – 6 angle parking; – 7 moving out of a parallel parking space.
Page 187: Special Note
ASSISTED PARKING (3/6) Special note Look in all directions Press and hold (icon) button – Drive slowly and always be ready to to start use the brake; – The system can not detect parking spaces between objects except for vehicles such as a post, motorbike or obstacle;...
Page 188 ASSISTED PARKING (4/6) Special note Look in all directions Go forward or reverse – While exiting the parking space, the system is disrupted for safety when there is risk to impact with obstacles; – The system may not be operated when the space is small;...
Page 189 ASSISTED PARKING (5/6) Suspending the manoeuvre Special note Make sure: – you have released the steering wheel The manoeuvre is suspended in the fol- The system may be disrupted in the and; lowing circumstances: following circumstances. In this cases, – that all doors and the boot are closed, –...
Page 190 ASSISTED PARKING (6/6) This function is an additional driving aid. However, this function is not under any circumstances intended to replace the due care and attention of the driver, who should at all times be in control of the vehicle. Make sure that the manoeuvre complies with the applicable traffic regulations at your location.
Page 191: Selector Lever
AUTOMATIC TRANSMISSION (1/3) Driving in automatic mode Move lever 1 to position D. In most road conditions you will en- counter, you will not need to touch your lever again: the gears will change au- tomatically at the right time and at the most suitable engine speed because the automatic system takes into ac- count the vehicle load and road contour...
Page 192: Automatic Gearbox
AUTOMATIC TRANSMISSION (2/3) Special cases Special circumstances In certain driving conditions (for exam- – If the bends and road surface do ple, engine protection, operation of the not allow you to stay in automatic Electronic Stability Programme: the au- mode (e.g. in the mountains), we tomatic system may change gear auto- recommend that you change to matically.
Page 193: Automatic Transmission
AUTOMATIC TRANSMISSION (3/3) Parking the vehicle Operating faults When the vehicle is stopped, move the – when driving, if the ‘check gearbox’ lever to position P while keeping your message appears on the instrument foot on the brake pedal: the gearbox is panel, it indicates a fault.
Page 194 2.90...
Page 195: Your Comfort
Section 3: Your comfort Air vents............... Manual air conditioning/heating system .
Page 196 AIR VENTS, air outlets (1/2) 1 left-hand air vent 2 side window demister outlets 3 windscreen demisting vents 4 centre air vents 5 right-hand air vent 6 multifunction screen 7 footwell heater outlets for front pas- sengers 8 footwell heater outlets for rear pas- sengers 9 centre air vents for rear seats...
Page 197: Centre Air Vents
AIR VENTS, air outlets (2/2) Centre air vents. Side air vents Air flow Air flow Move the control knob 11 or 12 (beyond Move the control knob 14 or 15 (beyond the resistance point). the resistance point). 11 left or 12 right: closed. 14 left or 15 right: closed.
Page 198 MANUAL AIR CONDITIONING (1/3) 10 11 12 The controls Indicators Switching air conditioning on or off 1 Adjusting the air temperature. The following indicators are displayed on the multimedia screen A: The air conditioning is switched on (in- 2 De-icing/demisting of the rear screen dicator light on) or off (indicator light off) and, depending on the vehicle, the 9 Air temperature.
Page 199: Manual Air Conditioning
MANUAL AIR CONDITIONING (2/3) Distribution of air in the passenger compartment There are five air distribution options. Turn control 5 to choose the distribution option. The air distribution is displayed on the multimedia screen. The air flow is directed to the õ...
Page 200 MANUAL AIR CONDITIONING (3/3) Clear view function Press button 8 - the intrgrated indicator light comes on. This function quickly demists and de- ices the windscreen, the rear screen, the front side windows, and the door mirrors (depending on the vehicle). The air conditioning and rear screen de-ic- ing functions must be activated.
Page 201: Automatic Climate Control
AUTOMATIC CLIMATE CONTROL: Controls A (1/5) Automatic mode The automatic climate control system- guarantees comfort in the passen- ger compartment and good visibility (except in the event of extreme condi- tions), while optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condi- tioning and air temperature.
Page 202 AUTOMATIC CLIMATE CONTROL: Controls A (2/5) The displayed temperature values Varying the ventilation speed Temperature adjustment show a comfort level. There are two types of settings: In automatic mode, the system uses – uniform passenger compartment When starting the engine, increas- the most suitable amount of air to reach setting;...
Page 203 AUTOMATIC CLIMATE CONTROL: Controls A (3/5) To exit this function, press either: – button 7; – again button 5; – on button 8, 9 or 10. Clear View function Press button 7 – the integrated indica- tor light comes on. This function quickly demists and de- Press button 4 to stop the heated rear ices the windscreen, the rear screen,...
Page 204 AUTOMATIC CLIMATE CONTROL: Controls A (4/5) Rear screen de-icing/ demisting Press button 3 – the integrated indica- tor light comes on. This function en- ables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles). To exit this function, press button 3 again.
Page 205 AUTOMATIC CLIMATE CONTROL: Controls A (5/5) Air recirculation Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle; – air recirculation allows the exter- nal atmosphere to be cut off (when driving in polluted areas, etc.) and to cool the passenger compartment temperature more quickly.
Page 206 AUTOMATIC CLIMATE CONTROL: Controls B and C (1/5) Automatic mode 3 B 11 The automatic climate control system guarantees comfort in the passen ger compartment and good visibility (except in the event of extreme condi tions), whilst optimising consumption. The system controls the ventilation speed, air distribution, air recirculation, and starting and stopping the air condi tioning and air temperature.
Page 207 AUTOMATIC CLIMATE CONTROL: Controls B and C (2/5) The displayed temperature values Varying the ventilation speed Temperature adjustment show a comfort level. There are two types of settings: In automatic mode, the system uses When starting the engine, increas- the most suitable amount of air to reach –...
Page 208 AUTOMATIC CLIMATE CONTROL: Controls B and C (3/5) To exit this function, press either: – again button 1; – one of the buttons 3. Clear View function Press button 1 – the integrated indica- tor light comes on. This function quickly demists and de- Press button 5 to stop the heated rear ices the windscreen, the rear screen, screen operating, and the integrated in-...
Page 209 AUTOMATIC CLIMATE CONTROL: Controls B and C (4/5) Rear screen de-icing/ demisting Press button 5 – the integrated indica- tor light comes on. This function en- ables rapid demisting or de-icing of the rear screen and de-icing of the door mirrors (on equipped vehicles).
Page 210 AUTOMATIC CLIMATE CONTROL: Controls B and C (5/5) Air recirculation Depending on the vehicle or country, Press button 8 or 9. Note: – during recirculation, air is taken from the passenger compartment and is recycled, with no air being taken from outside the vehicle;...
Page 211: Air Conditioning: Information And Advice On Use
AIR CONDITIONING: information and advice on use Advice on use Fuel consumption Operating faults In some situations, (air conditioning You will normally notice an increase in As a general rule, contact your ap- off, air recirculation activated, ventila- fuel consumption (especially in town) proved dealer in the event of an oper- tion speed at zero or low, etc.) you may when the air conditioning is operating.
Page 212: Outside Air Quality And Deodorisation Functions
OUTSIDE AIR QUALITY AND DEODORISATION FUNCTION Take care Deodorization cycle With the air conditioning switched Deodorisation function on, from the screen A, select Menu, This reduces unpleasant odours in the Vehicle, Take care. passenger compartment. Outside air quality Deodorization cycle –...
Page 213: Electric Windows
Driver’s responsibility Never leave your vehicle with the RENAULT card or key inside, and never leave a child, adult who is not self-sufficient or a pet, even for a short while. They may pose a risk to...
Page 214 ELECTRIC WINDOWS (2/2) One-touch mode Operating faults Depending on the vehicle, this mode In case of a fault when closing a window, works in addition to the operation of the the system reverts to normal mode: electric windows described previously. pull the switch concerned up as often It is only fitted to the driver’s window.
Page 215: Electric Sunroof
ELECTRIC SUNROOF (1/2) To tilt the sunroof When the sunroof is closed, press switch 2 to tilt up the sunroof. It doesn’t need to be held. When the sunroof is tilt, press switch 2 to close the sunroof. It doesn’t need to Driver’s responsibility be held.
Page 216 ELECTRIC SUNROOF (2/2) It doesn’t need to be held. The sun- – check that the sunroof is properly roof will automatically open or close all closed before leaving your vehicle; the way. To stop the window, push the – clean the seal every three months switch once more while it is opening or using products recommended by our closing.
Page 217: Interior Lighting
INTERIOR LIGHTING (1/3) Interior lights switch 1 Note: For vehicles fitted with a naviga- Front door lights 5 tion system, you can use the multifunc- Press switch 1 to turn on/off map read- tion screen to deactivate/activate the ing light 3 and 4. When a door is open, Front footwell lights 6 courtesy lights which come on when door light 5 and foot light 6 are ON.
Page 218 INTERIOR LIGHTING (2/3) Map reading lights switch 7, 8 Front and rear door ambient Center console ambient light light Press switch 7, 8 to turn on/off left or- Center console ambient light 9 comes right map reading light independently. on when the door is opened. Front and rear door ambient light 10 comes on when the door is opened.
Page 219 INTERIOR LIGHTING (3/3) Glove box light Boot lights Glove box light 11 comes on when the Light 12 comes on when the boot is illumination is turned on. opened. 3.25...
Page 220 PASSENGER COMPARTMENT STORAGE, FITTINGS (1/5) Front door storage pockets 1 Front sun visor Centre console storage compartment 4 They can hold a 1.5-litre bottle. Lower sun visor 2. Courtesy mirrors Lift the cover 3. Ensure that no hard, heavy or pointed objects are Nothing should be placed placed in the “open”...
Page 221 PASSENGER COMPARTMENT STORAGE, FITTINGS (2/5) Cup holders 5 Raise the button 7 to ventilate the stor- Front centre armrest storage age according to the temperature set compartment 10 This can be used for storing a mobile by the air conditioner. Lower the button ashtray, cup holder, etc.
Page 222 PASSENGER COMPARTMENT STORAGE, FITTINGS (3/5) Glove box Grab handle 12 Clothes hooks 13 To open the glove box, lift the catch 11. This offers support and can be held when the vehicle is being driven. Do not use it for getting into or out of the vehicle.
Page 223 PASSENGER COMPARTMENT STORAGE, FITTINGS (4/5) Coin holder 14 Sunglasses holder 15 Front seat storage pockets 16 (depending on the vehicle) (depending on the vehicle) Push 15 to open the sunglasses holder. 3.29...
Page 224 PASSENGER COMPARTMENT STORAGE, FITTINGS (5/5) Rear armrest with cup holder Rear door storage compartment 18 Pull down the armrest 17. When turning corners, Ensure that no hard, heavy accelerating or braking, or pointed objects are ensure that the recepta- placed in the “open” storage cle being held by the cup compartments in such a holder is not dislodged.
Page 225: Ashtray, Cigarette Lighter, Accessories Socket
ASHTRAY, CIGARETTE LIGHTER, ACCESSORIES SOCKET Ashtray location 1 Accessories sockets 3 They are provided for connecting ac- Cigarette lighter or cessories approved by our Technical Department. accessories sockets 2 With the ignition on, push in the ciga- rette lighter 2 - it will spring back with a click when it is ready.
Page 226: Rear Headrest
REAR HEADRESTS Position for use Centre seat headrest storage position Lift the headrest to maximum height, then lower it until it locks. Press the button A and lower the cen- tral headrest 1 completely. To remove a headrest When the headrest is set at the lowest position, this is for storage Raise the headrest as far as it will go, only.
Page 227 REAR BENCH SEAT (1/3) To replace the seatback, proceed in the reverse order to removal. Refit the seatback and click it back into place. When refitting the seat- back, make sure it is cor- rectly locked in place. To manually fold down the If seat covers are fitted, make sure these do not prevent the seatbacks...
Page 228 REAR BENCH SEAT (2/3) To automatically fold down Conditions of use Use restriction the seatbacks (flat position) – Vehicle stationary; It is forbidden to drive with a seatback or a front seat folded down when there Place seat belt in hook 2 to avoid dam- –...
Page 229 REAR BENCH SEAT (3/3) Press the left side of the switch to select the warmest setting or the right side of the switch to select the average setting. The middle position of the switch is off. The indicator light in the switch lights off.
Page 230: Boot
BOOT To open Opening the doors manually from the inside Press button 1 and lift the tailgate. If it is impossible to unlock the tailgate, it can be done manually from inside: To close – access the luggage compartment by Lower the tailgate using the handles 2 tilting the rear bench seatback(s), inside the tailgate to help you.
Page 231: Automatic Tailgate
– If there is any ice or snow prevent- Depending on the vehicle, you have se- control or using the RENAULT card ing the tailgate from opening, this ice veral different ways to manoeuvre the...
Page 232 With the ignition off, press and hold Press control 2. Press control 3. switch 1 on the RENAULT card. As a safety precaution, the doors should only be opened or closed when the vehicle is stationary. Risk of injury.
Page 233 – The «hands-free» feature may not work if the vehicle is equipped with a With the RENAULT card on your person towbar or is in an area of high elec- and with the ignition off, perform a for- tromagnetic radiation.
Page 234: Obstacle Detection
AUTOMATIC TAILGATE (4/5) Stopping the tailgate Obstacle detection manoeuvre When the tailgate window encounters an obstacle (presence of an object or The automatic tailgate manoeuvre can person) when it is moving, it stops. be stopped at any time by a short press Depending on the opening position, the on one of the controls.
Page 235 AUTOMATIC TAILGATE (5/5) Precautions during use Operating faults Before opening/closing the tailgate, If you activate the automatic tailgate ensure that the surrounding space is continuously for around a minute (se- sufficient to allow the tailgate to ope- quence of opening and closing), it will rate.
Page 236: Luggage Cover 2
LUGGAGE COMPARTMENT COVER Removing/refitting the luggage cover 2 Press the two ends 4 to maximum and move them towards the centre of the luggage compartment cover, then tilt the cover. To fit the luggage cover, carry out this procedure in reverse. To unfold the luggage To remove the flexible compartment cover 2...
Page 237: Luggage Net
LUGGAGE NET (1/2) Depending on the vehicle, this may be Fitting the luggage net – open the U-shaped area 6 to access used when transporting animals or lug- the anchoring point 4; behind the front seats gage to isolate them from the passen- –...
Page 238 LUGGAGE NET (2/2) Fitting the luggage net – latch the hook 10 to the anchoring point 11; behind the rear seats – adjust the net strap 9 so that it is taut. Inside the vehicle on each side: The seatbacks must not touch the –...
Page 239: Boot Fittings
BOOT FITTINGS Bag hooks 1 Anchorage points Maximum weight per hook: 3kg. Attachment points 2. Maximum weight on trunk board 3 is 60kg. If your vehicle is not equipped with anchorage points, you can get them from an authorised dealer. 3.45...
Page 240: Transporting Objects In The Luggage Compartment
TRANSPORTING OBJECTS IN THE LUGGAGE COMPARTMENT Always position the objects transported so that the largest surface is against: – The rear bench seatback for normal loads (example A). – The front seatbacks with the rear seatbacks folded down, the mobile floor in the flat-floor position (exam- ple B).
Page 241: Equipment
TRANSPORTING OBJECTS towbar Maximum dimension A: 1115 mm. Permissible nose weight, maxi- mum permissible towing weight, braked and unbraked: refer to the information on “Weights” in Section 6. Choice and fitting of towing equipment Maximum weight of towing equip- ment: 37 kg For fitting and conditions of use, If the towbar ball obscures the regis- refer to the equipment’s fitting in-...
Page 242: Roof Bars, Spoiler
ROOF BARS, SPOILER Precautions during use Handling the tailgate Before handling the tailgate, check the objects and/or accessories (bike rack, roof box, etc.) fitted to the roof bars: these must be correctly positioned and secured, so as not to hinder the opera- tion of the tailgate.
Page 243: Multimedia Equipment
MULTIMEDIA EQUIPMENT (1/2) Multimedia systems Hands-free telephone integrated control 1 Multimedia touchscreen; 2 Steering column controls; For equipped vehicles, use the steering 3 Steering wheel controls; wheel controls 3. 4 Microphone. Using the telephone We remind you of the need to conform to the legislation in force concerning the use Refer to the equipment instructions...
Page 244 MULTIMEDIA EQUIPMENT (2/2) Multimedia sockets 6 Sockets USB can only recharge acces- sories with a maximum power rating of 10.5 Watts (voltage: 5V) per socket, which have been approved by our Technical Department. The JACK socket enables the radio to be used with an auxiliary cable.
Page 245 Section 4: Maintenance Bonnet ............... . Engine oil level: general information .
Page 246: Bonnet
BONNET (1/2) Do not press down on the bonnet: there is a risk that the bonnet may accidentally close. To open, pull handle 1. Unlocking the bonnet catch When working in the engine To unlock, push tab 2 at the same time compartment, ensure that as opening the bonnet.
Page 247: Closing The Bonnet
BONNET (2/2) Closing the bonnet Check that nothing has been left in the engine compartment. To close the bonnet again, hold the bonnet in the middle and guide it down, allowing a 30 cm gap before it is closed, then release it. It will latch automatically under its own weight.
Page 248: Engine Oil Level: General Information
ENGINE OIL LEVEL: general information It is normal for an engine to use oil for – Remove the dipstick and wipe with a lubrication and cooling of moving parts clean, lint-free cloth; and it is normal to top up the level be- –...
Page 249: Engine Oil Level: Topping Up, Filling
ENGINE OIL LEVEL: topping up, filling (1/2) Topping up/filling – Unscrew cap 1; – top up the level (as a guide, the ca- The vehicle must be parked on level pacity between the minimum and ground and the engine should be cold maximum reading on the dipstick 2 (for instance, before the engine is is between 1.5 and 2 litres, depend-...
Page 250 ENGINE OIL LEVEL: topping up, filling (2/2) In order to prevent splashback, it is Do not exceed the max level and recommended that a funnel be used do not forget to refit cap 1 and dip- when topping up/filling with oil. stick 2.
Page 251: Engine Oil Change
ENGINE OIL LEVEL: OIL CHANGE Oil change Engine oil grade Service interval: refer Refer to the maintenance document for Maintenance Document for your vehi- your vehicle. cle. Oil change capacity Please refer to the maintenance docu- Filling: take care when ment for your vehicle, or contact an au- Consult your approved dealer at topping up the oil that...
Page 252: Levels
LEVELS (1/3) Frequency of checking coolant level Replacement interval Check the coolant level regularly Refer to the Maintenance Document for (very severe damage is likely to be your vehicle. caused to the engine if it runs out of coolant). If the level needs to be topped up, only use products approved by our Technical Department which ensure: –...
Page 253: Brake Fluid
LEVELS (2/3) Level 2 It is normal for the level to drop as the brake shoes become worn, but it must never drop lower than the “MINI” warn- ing line. If you wish to check the disc and drum wear yourself, you should obtain the document explaining the checking pro- cedure from the manufacturer’s net- work or web site.
Page 254: Windscreen Washer Reservoir
LEVELS /FILTERS (3/3) Filters The replacement of filter components (air filter, cabin filter, diesel filter, etc.) is scheduled in the maintenance opera- tions for your vehicle. Replacement intervals for filter el- ements: refer to the Maintenance Document for your vehicle. Before performing any action in the engine com- Windscreen washer reservoir...
Page 255: Tyre Pressure
TYRE PRESSURE (1/2) E: front tyre pressure. F: rear tyre pressure. G: tyre pressure for the emergency spare wheel. Vehicle fitted with a tyre pressure monitoring system In cases of under-inflation (puncture,  low pressure, etc.), warning light lights up on the instrument panel. Please refer to the information on the “Tyre pressure monitoring system”...
Page 256 TYRE PRESSURE (2/2) Special note concerning fully laden vehicles (Maximum Permissible All-Up Weight) and towing a trailer: the maxi- mum speed must be limited to 60 mph (100 kph) and the tyre pressure in- creased by 0.2 bar. Please refer to the information on “Weights”...
Page 257: Battery
BATTERY (1/2) Depending on the vehicle, a system continuously checks the battery charge status. If this decreases, the message “Battery low start engine” is displayed on the instrument panel. In this case, start the engine. The message will go off. The charge status of your battery can decrease especially if you use your ve- hicle:...
Page 258 BATTERY (2/2) Replacing the battery As this operation is complex, we advise you to contact an approved Dealer. Label A Observe the indications on the battery: – 2 Naked flames and smoking are for- bidden; – 3 eye protection required; –...
Page 259: Bodywork Maintenance
BODYWORK MAINTENANCE (1/2) What you should not do You should A well-maintained vehicle will last longer. It is therefore recommended to Do not degrease or clean mechani- Wash your car frequently, with the maintain the exterior of the vehicle reg- cal components (e.g.
Page 260 BODYWORK MAINTENANCE (2/2) Vehicles with a matte paint Using a roller type car wash Respect local regulations about wash- ing vehicles (e.g. do not wash your ve- finish Return the windscreen wiper stalk to hicle on a public highway). the Park position (refer to the informa- This type of paint requires certain pre- Observe the vehicle stopping distances tion on the “Windscreen washer, wiper”...
Page 261: Interior Trim Maintenance
INTERIOR TRIM MAINTENANCE (1/2) Glass instrument panel Textiles (seats, door trim, etc) A well-maintained vehicle will last longer. It is therefore recommended to (e.g.: instrument panel, clock, exterior Vacuum-clean the textiles regularly. maintain the interior of the vehicle regu- temperature display, radio display, mul- larly.
Page 262 INTERIOR TRIM MAINTENANCE (2/2) Removal/replacing removable You should not: equipment originally fitted in You are strongly advised not to po- the vehicle sition objects such as deodorants, scents, etc. near air vents, as this could If you need to remove equipment in damage your dashboard trim.
Page 263: Practical Advice
RENAULT card: battery ........
Page 264: Puncture, Emergency Spare Wheel
PUNCTURE, EMERGENCY SPARE WHEEL (1/2) In case of puncture Depending on the vehicle, a tyre infla- tion kit or emergency spare wheel is provided (refer to the following pages). Special note The Tyre Pressure Monitor function does not check the emergency spare wheel (the wheel replaced by the emer- gency spare wheel disappears from the instrument panel display).
Page 265 PUNCTURE, EMERGENCY SPARE WHEEL (2/2) Note: Store the punctured wheel in the storage bag provided, along with the tool kit and put them in the boot. Emergency spare wheel A To get to it: – open the tailgate; – remove the mobile floor 1; –...
Page 266 TYRE PRESSURE KIT (1/3) Do not attempt to use the The kit is only approved for inflation kit if the tyre has inflating the tyres of the ve- been damaged as a result hicle originally equipped of driving with a puncture. with the kit.
Page 267 TYRE PRESSURE KIT (2/3) With the engine running and the – after a maximum of 10 minutes, stop parking brake applied, inflating and read the pressure (on pressure gauge 1). – Unscrew the cap from recess 3 on the bottle; Note: while the container is empty- ing (approximately 30 seconds), the –...
Page 268 TYRE PRESSURE KIT (3/3) Precautions when using the – Affix the driving recommendation label to the dashboard where it can easily be seen by the driver; The kit should not be operated for more – Put the kit away. than 10 consecutive minutes. –...
Page 269: Tools
TOOLS Jack 2 Fold it correctly before refitting it in its housing. Jack handle 3 This tightens or releases the tow eye 4 Tow eye 4 Please see “Towing: breakdown recov- ery” in Section 5. The presence of the tools depends on Wheelbrace 1 the vehicle.
Page 270: Changing A Wheel
CHANGING A WHEEL (1/2) Attach the wheelbrace 1 and the jack handle 6 (in groove 5). Turn the wheelbrace until the wheel lifts off the ground. Vehicles equipped with a jack, wheelbrace and jack handle If the vehicle is not equipped with a If necessary, remove the wheel trim.
Page 271 CHANGING A WHEEL (2/2) Turn it a few times to lift the wheel off the ground. Undo the bolts and take off the wheel. Fit the emergency spare wheel on the central hub and turn it to locate the mounting holes in the wheel and the hub.
Page 272: Tyres (Tyre And Wheel Safety, Use In Winter)
TYRES (1/3) The tyres are the only contact between When the tread has worn down to the the vehicle and the road, so it is essen- wear warning strips, these strips will tial to keep them in good condition. become visible 2: it is then necessary You must make sure that your tyres to replace your tyres because the tread conform to local road traffic regulations.
Page 273: Tyre Pressures
TYRES (2/3) Tyre pressures The pressures should be checked cold: Vehicle fitted with a tyre pressure ignore higher pressures which may be monitoring system Adhere to the tyre pressures (including reached in hot weather or following a In cases of under-inflation (puncture, the emergency spare wheel).
Page 274 TYRES (3/3) Fitting new tyres Use in winter Studded tyres This type of equipment may only be Chains used for a limited period and as laid For safety reasons, fitting snow down by local legislation. It is neces- chains to the rear axle is strictly for- For safety reasons, this op- sary to observe the speed specified by bidden.
Page 275 FRONT HEADLIGHTS: changing bulbs (1/3) After replacing the bulbs, you must put the air duct A back into position. To do this, perform the above operation in re- verse. Accessing the bulbs On the right-hand side of the vehicle, you will need to remove the filler neck 4 On the left-hand side of the vehicle, for the windscreen washer tank to you will need to remove the air duct A...
Page 276 FRONT HEADLIGHTS: changing bulbs (2/3) It is essential to use anti-U.V. 55W bulbs so as not to damage the plastic on the headlights. Do not touch the bulb glass. Hold it by its base. When the bulb has been changed, make sure you refit the cover correctly.
Page 277: Headlights (Changing Bulbs)
FRONT HEADLIGHTS: changing bulbs (3/3) Front fog lights 11 Additional lights The front bumper needs to be removed; If you wish to fit fog lights to your ve- consult an approved Dealer. hicle, please see an authorised dealer. Bulb type: H11. LED front fog lights 11 Please see an authorised dealer.
Page 278 REAR AND SIDE LIGHTS: changing bulbs (1/3) Side lights and brake lights 1 Direction indicators 2 Consult an approved Dealer. Consult an approved Dealer. 5.16...
Page 279 REAR AND SIDE LIGHTS: changing bulbs (2/3) Reversing lights Turn bulb holder 4 fully anticlockwise and change the bulb. Open the tailgate. Refitting Unclip the trim 3 and remove it. To refit, proceed in the reverse order, taking care not to damage the wiring. Bulb type: W16W.
Page 280 REAR AND SIDE LIGHTS: changing bulbs (3/3) High level brake light 5 Halogen number plate Side indicator lights 8 lights 7 Consult an approved dealer. Consult an authorised dealer. – Unclip the light 7 (using a tool such as a flat-blade screwdriver). Rear fog lights 6 –...
Page 281: Interior Lighting: Changing Bulbs
INTERIOR LIGHTING: changing bulbs (1/2) Map reading lights 1 Ambient lights 2 Glove box lights 3 Please consult an authorised dealer. Please consult an authorised dealer. Please consult an authorised dealer. The bulbs are under pres- sure and can break when replaced.
Page 282 INTERIOR LIGHTING: changing bulbs (2/2) Front door lights 4, door Boot lights 7 ambient light 5, door storage Unclip light 7 by pressing the tabs on light 6 each side (using a flat-blade screw- driver or similar). Please consult an authorised dealer. Disconnect the light.
Page 283: Renault Card: Battery
RENAULT lock/unlock the vehicle (please refer to Note: it is not advisable to touch the card: the information on “Locking/unlocking...
Page 284: Radio Frequency Remote Control Unit: Batteries
RADIO FREQUENCY REMOTE CONTROL: batteries Replacing the battery Note: It is not advisable to touch the electronic circuit in the key cover when Open the case at slot 1 using a flat- replacing the battery. blade screwdriver or similar, and re- place the battery 2, observing the po- larity shown on the back of the cover.
Page 285: Fuses
FUSES (1/3) Fuses in passenger compartment A on the right-hand side of the vehicle Glove box needs to be disassembled to access the fuses. Please consult an au- thorised dealer. If any electrical component does not Fuses in passenger compartment B work, check the condition of the fuses.
Page 286 FUSES (2/3) Use the fuse allocation label in the stor- age compartment A or B to identify the fuses. Certain fuses should only be replaced by a qualified professional. These fuses are not listed on the label. Only change the fuses represented on the label.
Page 287 FUSES (3/3) Allocation of fuses (the presence of certain fuses depends on the vehicle equipment level) Symbol Allocation Symbol Allocation Symbol Allocation Vehicle dynamic BLOWER Ventilation H/MIRR Heated door mirrors control TURN HEATER Hazard lamp STOP LAMP Stop lamp Heater seat HAZARD SEAT POWER...
Page 288: Battery
BATTERY: troubleshooting (1/2) To avoid all risk of sparks: Connecting a battery charger – Ensure that any consumers (cour- The battery charger must be com- tesy lights, etc.) are switched off patible with a battery with nominal before disconnecting or reconnect- voltage of 12 volts.
Page 289 BATTERY: troubleshooting (2/2) Starting the vehicle using the battery from another vehicle If you have to use the battery from an- other vehicle to start, obtain suitable jump leads (with a large cross section) from an approved dealer or, if you al- ready have jump leads, ensure that they are in perfect condition.
Page 290: Accessories
ACCESSORIES Electrical and electronic accessories Before installing this type of accessory (particularly for transmitters/receivers: frequency bandwidth, power level, po- sition of the aerial, etc.), make sure it is compatible with your vehicle. You can get advice from an authorised dealer. Connect accessories with a maximum power of 120 Watts only.
Page 291: Windscreen Wiper Blades
WINDSCREEN WIPER BLADES: replacement (1/2) Refitting Slide the blade along the arm until it clips on. Check that it is correctly locked in place. Lower the windscreen wiper arm carefully. With the ignition on, return the wind- screen wiper stalk to the stop position. The blade on the driver’s side must always be above the passenger blade.
Page 292 WINDSCREEN WIPER BLADES: replacement (2/2) To refit To refit the wiper blade, proceed in re- verse order to removal. Make sure that the blade is correctly locked in position. Rear screen wiper blade 4 Stalk in stop position (deactivated): – Lift the wiper arm 6; –...
Page 293 Transport the vehicle on a trailer or tow pending on the vehicle, having the it with the front wheels off the ground. RENAULT card on you, press the In exceptional circumstances, you may engine start button for approximately tow it with all four wheels on the ground, 2 seconds.
Page 294 TOWING: breakdown recovery (2/4) 2WD vehicles When setting off, if the lever is locked in position P even though you are Vehicles fitted with an automatic pressing the brake pedal, the lever can transmission or continuously va- be released manually. To do this, unclip riable transmission.
Page 295 TOWING: breakdown recovery (3/4) 4WD vehicles Whichever type of gearbox is fitted, a 4WD vehicle must never be towed if any of its 4 wheels are touching the ground. vehicle must never be towed if one of its 4 wheels is touching the ground.
Page 296 TOWING: breakdown recovery (4/4) Do not leave the tools unse- cured inside the vehicle as they may come loose under braking. – Use a rigid towing bar. If a rope or cable is used (where the law allows this), the vehicle being towed Only use the front towing point A Access to towing points must be able to brake.
Page 297: Operating Faults
Dealer as soon as possible. Using the RENAULT card POSSIBLE CAUSES WHAT TO DO The RENAULT card does not lock or Card battery is flat. Replace the battery. You can still lock/ unlock the doors. unlock and start your vehicle (refer to the in- formation on “Locking, unlocking the open-...
Page 298 OPERATING FAULTS (2/7) The following advice will enable you to carry out quick, temporary repairs. For safety reasons you should always contact an approved dealer as soon as possible. Using the remote control POSSIBLE CAUSES ACTION REQUIRED The remote control does not lock or The remote control battery is flat.
Page 299 Starting conditions are not Please refer to the information on “Starting, stopping fulfilled. the engine” in Section 2. The RENAULT card does Please refer to the information on “Starting, stopping not work. the engine” in Section 2. The engine cannot be switched off.
Page 300 OPERATING FAULTS (4/7) On the road POSSIBLE CAUSES WHAT TO DO Vibrations. Tyres not inflated to correct pres- Check the tyre pressures: if this is not the sures, incorrectly balanced or dam- problem, have them checked by an ap- aged. proved Dealer.
Page 301 OPERATING FAULTS (5/7) On the road POSSIBLE CAUSES WHAT TO DO Steering becomes heavy. Assistance overheating. Consult an approved dealer. The engine is overheating. The cool- Engine cooling fan not working. Stop the vehicle, switch off the engine and ant temperature indicator is in the contact an approved dealer.
Page 302 OPERATING FAULTS (6/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO The wipers do not work. Wiper blades stuck. Free the blades before using the wipers. Faulty electrical circuit. Consult an approved dealer. Fuse damaged. Replace the fuse, refer to the information on “Fuses”.
Page 303 OPERATING FAULTS (7/7) Electrical equipment POSSIBLE CAUSES WHAT TO DO Traces of condensation in the lights. Traces of condensation may be a nat- ural phenomenon caused by varia- tions in temperature. In this case, the traces will disappear slowly once the lights are switched The front seat belt reminder light An object is stuck between the floor Remove all objects from underneath the...
Page 304 5.42...
Page 305: Technical Specifications
Section 6: Technical specifications Vehicle identification plate ............Engine identification plate .
Page 306: Vehicle Identification Plate
VEHICLE IDENTIFICATION PLATES The information shown on the ve- 4 MAM (Maximum Authorised hicle identification plate should be Mass). quoted on all correspondence or 5 GTW (Gross train weight: vehicle orders. fully loaded, with trailer). 6 MPAW (Maximim Permissible The presence and location of the in- Weight) for front axle.
Page 307: Engine Identification Plate
ENGINE IDENTIFICATION PLATES Please quote the information on the engine plate or label A in all corre- spondence or orders. (Location varies depending on engine) 1 Engine type. 2 Engine suffix. 3 Engine number.
Page 308: Dimensions
DIMENSIONS (in metres) 0,929 2,705 1,038 1,597 4,672 1,678* 1,592 2,063 * Unladen, with or without longitudinal roof bar...
Page 309: Engine Specifications
ENGINE SPECIFICATIONS Versions 2.0 GDi 2.5 16V 2.0 dCi 1.6 dCi Engine type QR25 M9R Turbo (see engine plate) Cubic capacity (cc) 1 997 2 488 1 995 1 598 Type of fuel Octane rating Diesel It is essential that you use unleaded petrol of the octane rating stated on the label inside the fuel The label located in the fuel filler flap filler flap.
Page 310: Towing Weights
WEIGHTS (in kg) The weights indicated for a basic vehicle without options: they vary depending on the your vehicle’s equipment. Consult your approved Dealer. Maximum permissible all-up weight (MMAC) Weights are indicated on the vehicle identification plate (refer to Maximum permissible all-up weight (MMTA) the information on “Vehicle identification plates”...
Page 311: Replacement Parts And Repairs
REPLACEMENT PARTS AND REPAIRS Original parts are based on strict specifications and are subject to highly-specialised tests. Therefore, they are of at least the same level of quality as the parts fitted originally. If you always fit genuine replacement parts to your vehicle, you will ensure that it performs well. Furthermore, repairs carried out within the manufacturer’s Network using original parts are guaranteed according to the conditions set out on the reverse of the repair order.
Page 312: Service Sheets
SERVICE SHEETS (1/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 313 SERVICE SHEETS (2/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 314 SERVICE SHEETS (3/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 315 SERVICE SHEETS (4/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 316 SERVICE SHEETS (5/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 317 SERVICE SHEETS (6/6) VIN: .................. Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □ ........□ Anti-corrosion check: OK □ Not OK* □ *See specific page Date: Miles (Km): Invoice number: Comments/miscellaneous Type of operation: Stamp Service □...
Page 318: Anticorrosion Check
ANTICORROSION CHECK (1/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.14...
Page 319 ANTICORROSION CHECK (2/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.15...
Page 320 ANTICORROSION CHECK (3/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.16...
Page 321 ANTICORROSION CHECK (4/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.17...
Page 322 ANTICORROSION CHECK (5/5) If the continuation of the warranty is subject to repair, it is indicated below. VIN: ............Corrosion repair operation to be carried Stamp out: Date of repair: Repair to be carried out: Stamp Date of repair: Repair to be carried out: Stamp Date of repair: 6.18...
Page 323: Alphabetical Index
ALPHABETICAL INDEX (1/5) blind spot: warning signal ........2.52 → 2.55 ABS ..............1.56, 2.31 → 2.34 bonnet................. 4.2 – 4.3 accessories................ 5.28 brake fluid ................4.9 accessories socket ............3.31 bulbs adaptive cruise control...........2.66 → 2.73 changing ............5.13 → 5.20 additional methods of restraint .......... 1.33 side protection .............
Page 324 ALPHABETICAL INDEX (2/5) windscreen ............3.4 → 3.6 dimensions ................6.4 4 wheel drive (4WD) ..........2.35 → 2.38 dipstick................. 4.4 faults display ..............1.54 → 1.61 operating faults ..........5.35 → 5.41 doors/tailgate ............1.4 → 1.16 filter driver assistance......2.56 → 2.58, 2.66 → 2.73 air filter .................
Page 325 ALPHABETICAL INDEX (3/5) heated seats ............. 1.20, 1.22 lighting: heating and air conditioning system ....3.4 → 3.6, 3.17 exterior .............1.79 → 1.86 heating system ............3.4 → 3.17 instrument panel ............1.79 Hill Start Assist............2.31 → 2.34 interior ..........3.23 → 3.25, 5.19 – 5.20 horn ...................
Page 326 ............... 5.22 sun visor ................3.26 remote control door locking unit ........1.2 → 1.4 sunroof..............3.21 – 3.22 RENAULT ANTI-INTRUDER DEVICE (RAID) ....1.16 switching on the vehicle ignition ......2.3, 2.5 → 2.9 RENAULT card battery ................5.21 use ........... 1.5 → 1.10, 2.5 → 2.9 tailgate ..........3.36 →...
Page 327 ALPHABETICAL INDEX (5/5) coolant ................4.8 tanks and reservoirs: warning lights............1.54 → 1.71 windscreen washer ............4.10 washing ..............4.15 – 4.16 technical specifications ..........6.4 → 6.7 weights ................6.6 telephone ..............3.49 – 3.50 wheelbrace ................5.7 temperature regulation ..........3.7 → 3.17 wheels (safety) ............5.10 →...
Page 330 à999101828Rî ú î ä E8 RENAULT S.A.S. SOCIÉTÉ PAR ACTIONS SIMPLIFIÉE AU CAPITAL DE 533 941 113 € / 13-15, QUAI LE GALLO 92100 BOULOGNE-BILLANCOURT R.C.S. NANTERRE 780 129 987 — SIRET 780 129 987 03591 / TÉL. : 0810 40 50 60...

Renault KOLEOS User Manual

Table of Contents

Section 2: Driving

Section 3: Your Comfort

Section 4: Maintenance

Section 5: Practical Advice

Quick Links

Chapters

Related Manuals for Renault KOLEOS

Summary of Contents for Renault KOLEOS

Table of Contents