Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for NEC Versa S900
Summary of Contents for NEC Versa S900
- Page 1 Versa S900 Disassembly Manual...
-
Page 2: Table Of Contents
Removing the Heat Sink............................11 Removing the CPU...............................12 Removing the LCD Display ..........................13 Disassembling the LCD Display ...........................13 Removing the Top Cover .............................15 Removing the Main Board............................16 Removing the MDC Modem ..........................18 Notice ...................................19 NEC Versa S900 Disassembly Manual Page 2... -
Page 3: Overview
Overview This document contains step-by-step disassembly instructions for the Versa S900 chassis. The instructions are illustrated where necessary with images of the part that is being removed or disassembled. Furthermore, the screws that are removed are shown next to the image of the parts themselves. -
Page 4: Hazardous Voltage
Inside the power supply are hazardous avviare il sistema senza aver prima messo a voltages that can cause serious personal injury. Always posto il coperchio return a defective power supply to your dealer. NEC Versa S900 Disassembly Manual Page 4... -
Page 5: Removing The Battery
1. Push the Versa Bay IV Lock and hold it in position as shown in (Fig. 2 ). 2. Pull the Versa Bay IV module out of the system. Fig. 2 Removing the Versa Bay IV Module NEC Versa S900 Disassembly Manual Page 5... -
Page 6: Removing The Memory Module
1. Unscrew the one screw holding the cover of the mini PCI card in place (Fig. 4 ). Fig. 4 Removing the cover of the mini PCI card 2. Disconnect the antenna wires marked in Fig. 5 . NEC Versa S900 Disassembly Manual Page 6... -
Page 7: Removing The Keyboard Cover And The Keyboard
2. Carefully tilt the keyboard cover, disconnect the cable shown in Fig. 7 and put the keyboard cover aside. Note: Be very careful when tilting the keyboard cover as you may damage the cable that connects the keyboard cover to the system. NEC Versa S900 Disassembly Manual Page 7... -
Page 8: Removing The Touchpad
To remove the touchpad, first remove the battery (see Removing the Battery), then perform the following steps: 1. Remove the screws from the battery compartment, as shown in Fig. 9 . Fig. 9 Removing the touchpad assembly screws NEC Versa S900 Disassembly Manual Page 8... - Page 9 4. Remove the screws marked in Fig. 12 Fig. 12 Removing the touchpad screws 5. Lift the topuchpad to remove it from its place as shown in Fig. 13 and put it aside. NEC Versa S900 Disassembly Manual Page 9...
-
Page 10: Removing The Hard Disk Drive
2. Take out of the system the hard disk drive holder that has come free after removing the screws in Fig. 14 . 3. Slide the hard disk drive as shown in Fig. 15 and lift it out of the system. NEC Versa S900 Disassembly Manual Page 10... -
Page 11: Removing The Heat Sink
To remove the heat sink, first remove the Keyboard (see Removing the Keyboard Cover and Keyboard), then perform the following steps: 1. Remove the screws shown in Fig. 17 to release the heat plate. Fig. 17 Removing the heat plate screws NEC Versa S900 Disassembly Manual Page 11... -
Page 12: Removing The Cpu
2. Carefully lift the CPU out of the socket and put it aside. Note: Handle the CPU with care when inserting or extracting it from the socket, in order not to bent or damage any pin. NEC Versa S900 Disassembly Manual Page 12... -
Page 13: Removing The Lcd Display
Disassembling the LCD Display To disassemble the LCD Display, first remove it from the base unit (see Removing the LCD Display), then perform the following steps: 1. Remove the rubber covers marked in Fig. 22 . NEC Versa S900 Disassembly Manual Page 13... - Page 14 4. Carefully unclip the LCD cover and put it aside. 5. Remove the screws shown in Fig. 24 to release the LCD panel and the inverter board. Fig. 24 Removing LCD panel and inverter board screws NEC Versa S900 Disassembly Manual Page 14...
-
Page 15: Removing The Top Cover
Fig. 26 Removing hinge screws Removing the Top Cover To remove the top cover, first remove the LCD display (see Removing the LCD Display), then perform the following steps: 1. Remove the screws marked in Fig. 27 NEC Versa S900 Disassembly Manual Page 15... -
Page 16: Removing The Main Board
5. Carefully lift up the top cover from the front side of the case and put it aside. Removing the Main Board To remove the main board, first remove the top cover (see Removing the Top Cover), then NEC Versa S900 Disassembly Manual Page 16... - Page 17 Fig. 32 Removing VGA port screws 5. Carefully lift up the main board and put it aside. Note: You can remove the wireless LAN button if it is in your way while removing the main board. NEC Versa S900 Disassembly Manual Page 17...
-
Page 18: Removing The Mdc Modem
1. Remove the two screws holding the mode in place.(Fig. 33 ) Fig. 33 Removing the MDC modem 2. Carefully lift the modem and disconnect any cable attached to it. NEC Versa S900 Disassembly Manual Page 18... -
Page 19: Notice
This guide contains information protected by copyright. No part of this guide may be photocopied or reproduced in any form or by any means without prior written consent from NEC Computers International BV. NEC COMPUTERS INTERNATIONAL BV SHALL NOT BE LIABLE FOR TECHNICAL OR EDITORIAL ERRORS OR OMISSIONS CONTAINED HEREIN;...