TurboChef Encore Manual

Daily Cleaning for the

Daily Cleaning

Follow the steps below when cleaning your Encore
cleaning chemicals. Failure to adhere to these procedures or the use of any other cleaning
products may damage critical oven components, resulting in a non-warranty service call.
Step 1: Cool the Oven
WARNING: The oven operates at approximately 500°F
!
(260°C) and may cause injury if not allowed to cool properly.
• Turn off the oven by pressing the On/Off key.
• Slightly open the oven door.
• Cooling takes approximately 30 minutes.
DO NOT proceed to Step 2 until the oven displays "ready
to clean."
Step 1
Step 2: Clean the Wire Rack
• The wire rack is held in place by tabs that are positioned
underneath either side of the jetplate.
• Lift the rear of the wire rack.
• Pull the wire rack forward until the tabs are free.
• Wash, rinse, sanitize, and dry the wire rack.
Tab Location
Step 2
Step 3: Clean the Jetplate
• Lift the front of the jetplate.
• Pull the jetplate forward and remove it from the oven.
CAUTION: Handle the jetplate with care to avoid
!
chipping the porcelain coating.
• Wash, rinse, sanitize, and dry the jetplate.
DO NOT clean the jetplate with a wire brush.
Step 3
Step 4: Clean the Air Filter
The filter must remain in place during oven operation, and it
must be cleaned regularly or replaced if damaged.
• Remove the air filter from the back of the oven.
• Rinse the air filter with hot water.
• Allow the air filter to dry completely.
Step 4
Step 5: Remove Large Food Particles
• The heating element can be lifted for cleaning underneath.
DO NOT attempt to clean the heating element.
• Use a food vacuum or damp towel to remove large
particles from the oven cavity.
Step 5
Step 6: Clean the Oven Cavity
DO NOT spray TurboChef ® Oven Cleaner into the holes
in the oven cavity.
• Apply Oven Cleaner to a towel or nylon scrub pad
and clean the top, sides, and bottom of the cavity.
Step 6
Customer Service: 800.90TURBO (within U.S.)
Customer Service: +1 214-379-6000 (outside U.S.)
©2011 TurboChef Technologies, Inc.
oven. Use only TurboChef ®-approved
tm
Oven
Encore
tm

Supplies and Equipment

TurboChef ® Oven Cleaner (Product Number: 103180), TurboChef ® Oven Guard
(Product Number: 103181), Kay ClickSan® sanitizer, nylon scrub pad, clean damp
and dry towels, disposable gloves, protective eyewear, dust mask (optional)
Step 6, Continued: Clean the Oven Cavity
DO NOT apply excessive pressure to the waveguide
A
covers (A), located on each side of the cavity.
• For stubborn stains, sparingly spray Oven Cleaner
on the stain.
• Allow the Oven Cleaner to penetrate the stain for five
minutes, then wipe clean.
DO NOT use a hose or water jet for cleaning.
Step 6
Step 7: Wipe Down the Oven Cavity
• Wipe down the oven cavity with a damp towel.
• Dry the oven cavity with a dry towel.
Step 7
Step 8: Clean and Dry the Oven Door
• Clean the oven door with Oven Cleaner and a nylon
scrub pad.
• Wipe the oven door with a damp towel.
• Dry the oven door with a dry towel.
Step 8
Step 9: Apply TurboChef ® Oven Guard
• Spray TurboChef ® Oven Guard onto a dry towel.
• Wipe the cavity walls and the inside of the oven door.
DO NOT spray Oven Guard into the oven or apply to
the heating element.
Step 9
Step 10: Reinstall Components
• Reinstall the jetplate and the wire rack.
DO NOT operate the oven without the bottom
jetplate installed.
• Close the oven door.
• Reinstall the filter, or replace it with a new one if the
mesh is deteriorated, has large openings, or has started
to dislodge from the frame.
Step 10
Step 11: Clean the Oven Exterior
• Wipe the oven exterior with a damp towel.
• Remove the panel beneath the door, remove any large food
particles from the panel, and wipe it with a damp towel.
• Reinstall the panel beneath the door.
DO NOT spray chemicals into any openings, such as the
louvers on the side panels or the rear vent catalyst housing.
• The oven is ready to turn on.
Step 11
tm
Part Number: DOC-1318 / Rev B / Oct 2011
Country Code: NA/EU