Avery Dennison Cutter 2000 Technical Manual
  1. Manuals
  2. Brands
  3. Avery Dennison Manuals
  4. Printer Accessories
  5. Cutter 2000
  6. Technical manual
Avery Dennison Cutter 2000 Technical Manual

Avery Dennison Cutter 2000 Technical Manual

Hide thumbs Also See for Cutter 2000:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Spare Parts List
03/10 Rev. 5.04-01
Safety Notes ................................................. 2
General Notes ............................................... 3
Proper Usage ............................................ 3
Technical Specifications ............................ 3
System requirements .................................... 4
Connecting the cutter .................................... 5
Activating the cutter ...................................... 7
Activating the TTX 350 / TTK .................... 7
AP 7.t ......................................................... 7
Parameter settings .................................... 8
TECHNICAL MANUAL
Cutter 2000
Status reports ............................................9
Triggering a cut ..........................................9
Servicing the cutter ......................................10
General notes ..........................................10
Cutter motor .............................................10
Toothed belt .............................................11
Photoelectric switch .................................11
Circular cutter ..........................................13
Bottom cutter ...........................................15
Accessories .................................................16
Stripper plate ...........................................16
Appendix .....................................................17
Cable harness ..........................................17

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Cutter 2000 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Avery Dennison Cutter 2000

Summary of Contents for Avery Dennison Cutter 2000

  • Page 1: Table Of Contents

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Cutter 2000 Connection, Setup, Service Safety Notes ..........2 Status reports ..........9 General Notes ..........3 Triggering a cut ..........9 Proper Usage ..........3 Servicing the cutter ........10 Technical Specifications ......3 General notes ..........10 System requirements ........

  • Page 2: Connection, Setup, Service

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Safety Notes WARNING! Danger of getting your fingers cut by the cutter blades! Cleaning of the cutter must be done very carefully. Don´t touch the cutter during printing/cutting operation. Don´t use the cutter as a handle to carry the printer.

  • Page 3: General Notes

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 General Notes Proper Usage The cutter option (subsequently referred to as the "cutter") is a peripheral de- vice for label printers of the type TTK, TTX 350, 64-xx, AP 5.4, AP 5.6 or AP 7.t.

  • Page 4: System Requirements

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 System requirements Cutters in the appropriate width can be operated with the following printers: System Requirements Printer Cutter width 4" 64-04 / TTK / TTX 350 / AP 5.4 / AP 7.t 5"...

  • Page 5: Connecting The Cutter

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Connecting the cutter WARNING! Danger of injury if the cutter is activated unintentionally! Before beginning service work, switch off the printer and pull out the mains power supply plug. The cutter (fig. 1) is secured to the printer by two screws and an adjustment plate.
  • Page 6 03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 4. Attach the adjustment plate (5) by unscrewing the top left hexagonal screw (6) on the print or draw unit, place the adjustment plate underneath, and then tighten the screw again - initially only lightly (fig.

  • Page 7: Activating The Cutter

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Activating the cutter After installation, the cutter must still be activated by setting the correspon- ding parameters in the parameter menu. WARNING! Danger of cutting hands and fingers! Activating a non-existent option (peri- pheral device) can cause the device to malfunction.

  • Page 8: Parameter Settings

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Unmount the cutter to clean the light sensor (1). Check, if the cutter cable is damaged. If so, replace the cable. Adjust the oscillator disc (see section “Oscillator disc” – “Setting the oscillator disc”).

  • Page 9: Status Reports

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Status reports The following status reports may be displayed in conjunction with the cutter function: TTX 350 TTK 64-xx / AP 5.4 / AP 5.6 / AP 7.t Example, comment...

  • Page 10: Servicing The Cutter

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Servicing the cutter General notes WARNING! Danger of injury! There is a risk of being cut while carrying out service work on the cutter! Avoid touching the cutter blades. Handle the cutter very cautious.

  • Page 11: Toothed Belt

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Toothed belt Tool Allan key 3 mm Disassembling/assembly 1. Remove the motor cover and the motor. For more detailed information, see the section "Cutter motor". 2. Remove the toothed belt (1). Turn the...

  • Page 12: Oscillator Disc, Toothed Wheel

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Oscillator Disc, Toothed Wheel The oscillator disc (1) and toothed wheel (2) both sit on the motor end of the circular cutter (fig. 1). Tool Allan key 3 mm Disassembling/assembly 1.

  • Page 13: Circular Cutter

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Circular cutter WARNING! Danger of injury! There is a risk of being cut while carrying out ser- vice work on the cutter! Avoid touching the cutter blades. Handle the cutter very cautious.
  • Page 14 03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Adjustment 1. Set the position of the oscillator disc as described in the section "Oscillator disc, toothed wheel". 2. Secure the cutter in a bench vice (fig. 1). WARNING! Danger of injury! There is a risk of...

  • Page 15: Bottom Cutter

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Bottom cutter The bottom cutter (1) is attached to the square axle (2) by a spring plate (3). The bottom cutter, spring plate and square axle are only available as pre-configured spare parts.

  • Page 16: Accessories

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Accessories Stripper plate If the applied label material is very thin and flexible, it may happen, that the label material is drawn upwards together with the ribbon, instead of being fed into the cutter.

  • Page 17: Appendix

    03/10 Rev. 5.04-01 TECHNICAL MANUAL Connection, Setup, Service Cutter 2000 Appendix Cable harness...

Table of Contents