Accessing The Programming Mode; Security Code - Viking E-1600-02A Technical Practice

E - 1 6 0 0 - 5 5
E - 1 6 0 0 - 5 5
The E-1600-55A is a universal emergency phone kit for installing behind elevator panels, or an installation requiring a custom panel. The finished panel
should provide: (4) studs (#6 diameter minimum) for mounting plate, audio holes for speaker and microphone, a momentary SPST push button switch and
a 0.25" diameter mounting hole for the LED. Alternatively, the LED can be cut off and the wires connected to a integral switch with LED (often found in
elevators). Note: An LED must be connected to the red and black wires for the phone to operate.
Optional Enhanced Weather Protection (EWP):
The optional EWP products feature foam rubber
gaskets and boots, sealed connections, gel-filled
butt connectors, as well as urethane or thermal
plastic potted circuit boards. See DOD# 859.
Shipping Weight: .73 kg (1.6 lb)
Connections: Telco and Switch - Gel-filled butt
connectors
Material: 0.062" thick (16 gauge) zinc
plated steel
4.0"
Dust Cover -
Install prior to fastening
faceplate to finished panel.
Wire
Knockout
P r o g r a m m
P r o g r a m m
A. Accessing the Programming Mode
The 1600A Series emergency phones can be programmed from any Touch Tone phone using a C.O. line, analog PABX/KSU sta-
tion, or a DLE-200B Line Simulator. For more information on the DLE-200B, see DOD# 605.
1. Using the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls, see section J).
Step 2. From a Touch Tone phone call the line attached to the 1600A Series phone.
Step 3. When the 1600A Series phone answers, enter the 6-digit security code (factory set to 845464, see section C). A
double beep should then be heard indicating you have entered the programming mode.
2. Without the Security Code
Step 1. Move DIP switch 2 to the ON position (sets unit to answer incoming calls, see section J).
Step 2. Move DIP switch 3 to the OFF position (incoming calls enter Programming without security code, see section J).
Step 3. From a Touch Tone phone call the line attached to the 1600A Series phone.
Step 4. When the 1600A Series answers, a double beep will be heard and will automatically enter the programming mode.
Step 5. When finished programming, move DIP switch 3 back to the ON position (see section J).
Warning: Failure to do step 5 above will cause the 1600A Series phone to call Viking Technical Support instead of your
programmed emergency number.
B. Security Code
(memory location #19)
The security code allows the user/installer to program the 1600A series phone while DIP switch 3 is in the ON (normal)
position. The factory set security code is 845464 (V-I-K-I-N-G). It is recommended that the factory set security code
be changed. Example: To store 123456 as the security code:
Step 1. Access programming as shown is Programming section A.
Step 2. Enter 123456 #19..
Step 3. Hang-up.
Note: The security code must be 6 digits and cannot include a Q or a #.
6
A
A
( o p t i o n a l E
( o p t i o n a l E
Connect to
phone line
Red "Call Connected" LED with
included mounting hardware
(requires a 0.25" diameter hole)
Note: If you do not want to use the
LED, tuck it inside the unit.
Do NOT cut it off.
Clear Spacer Red 5mm Retaining
Lens
Connect to momentary push
2.1"
button switch with contact
rating of 50VDC/100mA min
*
Note: Additional wire length may be
added if required.
(4) Countersunk holes for
mounting the dust cover
(4) 0.25 diameter clearance holes
for mounting the unit to the back
side of a finished panel.
(4) 6-32 x 3/4" stainless steel flat head,
5/64" hexdrive, screws (included) for
fastening dust cover
i n g
i n g
W P a v a i l a b l e )
W P a v a i l a b l e )
Gel-filled butt
connectors
Red
Green
Drip Loop
Diameter
Red (LED
anode)
*
Black (LED
cathode)
Round LED Ring
*
Black
Black
1/16" thick foam gasket (included) for accoustically sealing
mic and speaker to back of finished panel. Remove backing
and adhere gasket to front panel of the E-1600-55A,
centering over speaker and microphone holes (as shown).
4.50
2.25
2.0
0.25
Diameter
5.0
Enter Your Security Code Here:
0.25 Typ.
1.76
3.625
Typ.
5.0
3.77
4.50
(4) 0.25 diameter
holes (not used)
304 stainless steel speaker and
microphone protection screens
#19