Vivotek IP8372 Quick Installation Manual
Bullet network camera
Hide thumbs
Also See for IP8372:
- User manual (201 pages) ,
- Specification (2 pages) ,
- Specification (6 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Vivotek IP8372
Summary of Contents for Vivotek IP8372
- Page 1 IP8372 Bullet Network Camera Quick Installation Guide Русский Česky Svenska Nederlands 繁中 簡中 日本語 Deutsch Italiano Türkçe English Français Español Português Polski Indonesia Dansk Outdoor • Day & Night • Weather-proof • IP67 • Cable Management...
-
Page 2: Package Contents
Do not insert sharp or tiny objects into the Network Camera. Package Contents Sun Shield / Wrench / RJ45 Female / IP8372 with an RJ45 Cable Female Coupler / Double-sided Tape / Screws Waterproof Connector for RJ45 Wall Mount Bracket... -
Page 3: Physical Description
Quick Installation Guide Software CD IP8361 Network Bullet Camera Quick Installation Guide English 繁中 簡中 日本語 Français Español Deutsch Português Italiano Türkçe Polski Русский Česky Svenska 2MP • Outdoor • Day & Night Cable Management Warranty Card Physical Description Lens IR LED Light Sensor Auto Focus... -
Page 4: Hardware Installation
Hardware Installation 1. Attach the alignment sticker to the wall. Drill four holes into the wall. Then hammer the supplied plastic anchors into the holes and secure the plate with supplied screws. 2. Fix the intersection bracket to the side of the Network Camera with two screws. 3. -
Page 5: Waterproof Connector
Waterproof Connector Components of the Waterproof Connector Screw Nut (A) Seal (B) Seals (C) Housing (D) Sealing Nut (E) Pin Definitions Do+ (12V) Digital Output Digital Input 1 Ground Digital Input 2 Ground TV Out + TV Out - Ext. MIC Audio Ground Audio Line out Audio Ground... - Page 6 Assembling Steps 1. Disassemble the components of the waterproof connector into part (A) ~ (E) as shown above. 2. Open the rear cover of the Network Camera. 3. Remove the rubber stopper from the bottom of the Network Camera and secure the screw nut (A) tightly.
-
Page 7: Cabling Assembly
Cabling Assembly RJ45 Cable Connector RJ45 Cable Dimension (unit: mm) Components of the Waterproof Connector Sealing Nut (A) Seal (B) Screw Nut (C) Housing (D) Gasket (E) Assembling Steps Insert the housing into the Insert the seal into the housing. Prepare an Ethernet cable screw nut. -
Page 8: Network Deployment
Network Deployment Power over Ethernet (PoE) When using a PoE-enabled switch The Network Camera is PoE-compliant, allowing transmission of power and data via a single Ethernet cable. Follow the below illustration to connect the Network Camera to a PoE-enabled switch via Ethernet cable. PoE Switch When using a non-PoE switch Use a PoE power injector (optional) to connect between the Network Camera and a non-PoE... -
Page 9: Assigning An Ip Address
2. The program will conduct an analysis of your network environment. After your network is analyzed, please click on the "Next" button to continue the program. 3. The program will search for VIVOTEK Video Receivers, Video Servers, and Network Cameras on the same LAN. - Page 10 2. Attach the supplied sun shield to the Network Camera and slide it to the desired position. 3. Fix the sun shield with the supplied two screws. Accessories VIVOTEK also provides other accessories for versatile applications as the following illustrations. Please visit VIVOTEK's official website for more purchase information. Pole Mount Bracket...
- Page 11 P/N:625018900G Rev. 1.0 All specifications are subject to change without notice. Copyright 2012 VIVOTEK INC. All rights reserved. VIVOTEK INC. VIVOTEK USA, INC. 6F, No.192, Lien-Cheng Rd., Chung-Ho, New Taipei City, 235, Taiwan, R.O.C. 2050 Ringwood Avenue, San Jose, CA 95131 |T: +886-2-82455282| F: +886-2-82455532| E: sales@vivotek.com...
Need help?
Do you have a question about the IP8372 and is the answer not in the manual?
Questions and answers