Visonic PowerMaxExpress Quick Reference Manual page 2

3.
To Access the Installer Mode
shows "Installer Mode", then press
code 9999.
Whilst in any of the menus (user or installer) the following keys
will help you navigate the systems:-
– Away - returns you to the start of the main menu
– Home - takes you back to the previous menu
– Next - scrolls forward in the menu
- Back - scrolls back in the menu
- takes you in to a menu or press twice to confirm changes
4.
Before you Install the Accessories
you carry out a diagnostic check which is in section 7 of this guide.
Each device is labelled with its zone number. Make sure you
note this before installing.
Additionally, each sensor supplied in this kit is pre- programmed
for the following:
•
Zone 1 - Front Door Contact. 'Delay 1' to start the Entry timer
•
Zone 2 - Hall PIR. 'Home Delay' to allow user to walk through
during entry time to disarm
•
Zone 3 - Living Room PIR 'Perimeter' which will trigger the
alarm once armed
PIR motion sensors are supplied with pet-tolerant lens already
fitted. Within the kit a standard lens is supplied which should
be used in non pet-tolerant environments. PIR's should be sited
to ensure that they do not face into direct sunlight, windows,
strong sources of heat and cold (i.e. heaters, radiators, cold
drafts or ventilators).
They should also be mounted at the correct height (between
1.8 – 2.4m) in a position. For PET sensor applications ensure the
unit is not facing stairs and that animals can not move within
1M of the device.
To install, remove the cover, unclip the PCB, drill and fit in to
position being careful not to over tighten the screw and distort
the backplate. Then refit the PCB in to the back plate ensuring
the back tamper switch sits on to the metal spring .
Next PIR
L Wireless PIR's have a two minute sleep timer to save battery
life – On initial power up the unit will go through a self test
(LED flashing) then enter a walk test mode. If the PIR has
gone into sleep mode vacate the room for two minutes, or
open and close, the lid before carrying out the walk test.
press until the display
and enter the installer
we recommend that
MCT-320 Door Contact has a built in reed switch, for use with
the magnet supplied.
To install the main transmitter to the door or window frame,
ensuring that the curved edge is facing the opening section.
The magnet should be installed on the opening section no more
than 5mm from the transmitter.
MCT-320
L If the gap between the MCT-320 and magnet is too great
use the 7mm plastic spacer, provided within the kit, to
increase the height of the magnet.
5.
Enrol Additional Devices
their packaging and opening the cases near the PowerMax.
Then, whilst in installer mode (see 3. Accessing the Installer
mode) press until 'Enrolling' is shown, press
For PIR Movement sensors, Door Contact, Glassbreaks, Shock
Sensors etc :-
•
Press until [Enrol Sensors] is show on the screen. Press
. At [Set Sensitivity] press
•
Press until you get to the next available zone (as default
this will be zone 4) which will be indicated by having no black
marker on the right of the screen.
•
Press 'Transmit now' will be on screen.
•
Add the battery supplied to the sensor you wish to enrol to
this zone.
•
Trigger a tamper on the sensor, trigger the input (for universal
or aux input on door contacts) or press button (for hand held
devices) to initiate a transmission.
•
Remove battery from transmitter, press
enrol an additional device.
L If a sensor has already been enrolled in another zone a
long error tone will be heard and the sensor will not be
accepted again.
L PIR's have back tampers which require both the front and
back tamper switch to be pressed simultaneously during
enrolling.
Up to two MCS Sirens can be enrolled. Within the enrolling menu:-
•
Press until [Enrol Siren] is show on the screen. Press
. Enter the siren number to enrol (1 or 2) then press
•
At the siren ensure the battery is connected then press the
self test button until the unit emits a short tone from the piezo
and flashed.
•
The panel LCD will now show the siren number with a black
mark right hand side. Enrolment is complete. Press HOME to
escape back to the previous menu/s.
by first removing them from
then:-
, then again.
, then to