How To Use The Dual Mode - Fostex DE-10 Owner's Manual

DE-10 Owner's Manual
We describe how to use the Dual Mode below.
<About features of the Dual Mode>
1. You can use the DE-10 as a two-channel effect processing unit.
2. Each effect processor (EFFECT 1 and EFFECT 2) provides a mono input and stereo output jacks.
3. A main parameter for each effect can be edited from the preset value.
The following shows the example of using the dual mode, in which the DE-10 is connected between the AUX SEND
and AUX RTN jacks for applying the desired effect to a sound.
<Point>
Connect the Foot SW
into the jack to re-
motely control the
Effect Mute ON/OFF.
MODE SINGLE1/DUAL SINGLE 2
G
DELAY DISTORTION
H MISC G.MULTI 1
I CHORUS G.MULTI 2
J PITCH B.MULTI
K FLANGER VO.MULTI
<Front panel settings>
1. Set the MODE switch to "DUAL".
2. Set the TYPE switch for each of EFFECT 1 and 2 to the
desired position.
You can select from among the following eleven types.
See page 5~7 for details about each type.
MODE
SINGLE 1/DUAL SINGLE 2
SW
A L. HALL L. HALL
B S. HALL S. HALL
C ROOM ROOM
D PLATE
PLATE
E VOCAL MIC SIM
F DELAY + REV AMP SIM
3. Set the VARIATION switch for each of EFFECT 1 and 2 to
the desired position.
4. Using the appropriate ADJUST control, adjust the
parameter for each of EFFECT 1 and 2.
5. Using the appropriate MIX control, adjust the mixing
balance of dry and effect signals fed from the OUTPUT
jacks for each of EFFECT 1 and 2.

How to use the Dual Mode

FOOT SW
model 8051
EFF MUTE
TYPE VARIATION ADJUST
PARAM.1
DRY+EFF
F 6
E G 5 7
D H 4 8
I
C 3 9
10
B J 2
DRY
11
A K 1
PEAK
3 4
2
MODE
SINGLE 1/DUAL SINGLE 2
SW
G DELAY DISTORTION
H MISC G. MULTI 1
I CHORUS G. MULTI 2
J PITCH B. MULTI
K FLANGER VO. MULTI
Adjust the incoming signal level
from the mixer. See <Caution on
Effect Processing> below for details
about how to adjust the level.
R L R L
(MONO) (MONO)
OUTPUT 2 OUTPUT 1
AUX RTN
TYPE
MIX VARIATION
DLY+REV
MODE
VOCAL DELAY 5
SINGLE2 PLATE MISC 4
SINGLE1 DUAL
ROOM CHO 3
S.HALL PITCH 2
EFF
L.HALL FLANGE 1
PEAK
5 2 3
1
<About PEAK indicator>
The PEAK indicator on the front panel illuminates when
the input signal to be monitored reaches 6 dB below the
clipping level. Adjust the input level appropriately so
that the PEAK indicator occasionally flickers. If you hear
the output sound distorted though the PEAK indicator
does not steadily light or illuminate so often, it may be
due to the signal level increase in the effect processing.
In such a case, reduce the input level so that the output
sound is not distorted.
<Note on changing the switch position>
When you change the position of the MODE, EFFECT TYPE,
or VARIATION switch, the DE-10 resets the internal DSP
and the output signal disappears momentarily. This is
due to not a malfunction.
<Notes on using the ADJUST and MIX controls>
• When you turn the ADJUST or MIX control, a click may
be generated with some effect type.
• If the default of a parameter is the maximum or
minimum value, you cannot increase or decrease the
value using the ADJUST control, respectively.
18
LINE MIC/G
Set the input se-
lector to "LINE".
2 1 (1&2)
DUAL MODE
R
SINGLE MODE L(MONO)
LINE MIC/G
MIN MAX MAX
MIN
LINE INPUT (-10dBV) MIC/GUITAR INPUT
AUX SEND
MIXER
EFFECT 2
ADJUST
MIX
PARAM.2 PARAM.3
6 DRY+EFF
7
8
EFF MUTE
9
10
DRY EFF
1 1
4 5
TRIM
MIC
GUITAR
POWER