Names And Functions (Front Panel Section) - Fostex DE-10 Owner's Manual

DE-10 Owner's Manual
EFFECT 1
MODE SINGLE1/DUAL SINGLE 2 MODE SINGLE1/DUAL
A L.HALL L.HALL G DELAY
B
S.HALL S.HALL H MISC
C
ROOM ROOM I CHORUS
D PLATE PLATE J PITCH
E VOCAL MIC SIM K FLANGER
F DELAY+REV AMP SIM
1. EFFECT 1 TYPE switch
Selects the type for EFFECT 1 in the dual mode or for the
effect in the single (1 or 2) mode.
You can select from among 11 effect types for each mode
as shown in the table below.
MODE
SINGLE 1/DUAL SINGLE 2
SW
L. HALL
A L. HALL
S. HALL
B S. HALL
C ROOM
ROOM
D
PLATE PLATE
E VOCAL MIC SIM
F AMP SIM
DELAY + REV
2. EFFECT 1 PEAK indicator
Lights up when the input level of EFFECT 1 in the dual
mode or of the effect in the single (1 or 2) mode exceeds
"+6 dB" which is just below the clipping level.
3. EFFECT 1 VARIATION switch
Selects the variation for EFFECT 1 in the dual mode or for
the effect in the single (1 or 2) mode.
You can select from among 11 variations.
4. EFFECT 1 ADJUST/PARAM. 1 control and indicator
Adjusts the parameter value for EFFECT 1 in the dual mode
or the parameter 1 value for the effect in the single (1 or
2) mode. The center position is the default. Turning left
decreases the value while turning right increases the value.
5. EFFECT 1 MIX control
Adjusts the balance of the output sound from the
OUTPUT 1 jacks on the rear panel in the dual or single
mode.
• Hard left :DRY 100%, EFFECT 0%
• Center :DRY 50%, EFFECT 0%
• Hard right :DRY 0%, EFFECT 100%
6. MODE select switch
Selects the mode between DUAL, SINGLE 1 and SINGLE 2.
7. EFFECT 2 TYPE switch
Selects the type for EFFECT 2 in the dual mode. This switch
does not function in the single (1 or 2) mode.
You can select from among 11 effect types, as same as
EFFECT 1.
8. EFFECT 2 PEAK indicator
Lights up when the input level of EFFECT 2 in the dual
mode exceeds "+6 dB" which is just below the clipping
level. This indicator does not function in the single (1 or
2) mode. We recommend to adjust the INPUT LEVEL
control on the rear panel appropriately so that this
indicator sometimes lights up.
Names and Functions
TYPE VARIATION
F 6
SINGLE 2
E G 5 7
DISTORTION
D H 4 8
G.MULTI 1
I
C 3 9
G.MULTI 2
B.MULTI
B J 2 10
11
VO.MULTI A K 1
PEAK
1 2 3
MODE
SINGLE 1/DUAL
SW
DELAY DISTORTION
G
H MISC G. MULTI 1
I CHORUS G. MULTI 2
J
PITCH
K FLANGER
(Front panel section)
ADJUST MIX TYPE
PARAM.1
DRY+EFF
DLY+REV
MODE
VOCAL
SINGLE2 PLATE
SINGLE1 DUAL
ROOM
S.HALL
DRY EFF
L.HALL
4 6 7 8 9
5
9. EFFECT 2 VARIATION switch
Selects the variation for the effect type selected for
EFFECT 2 in the dual mode.
This switch does not function in the single (1 or 2) mode.
You can select from among 11 variations, as same as
EFFECT 1.
SINGLE 2
10. EFFECT 2 ADJUST/PARAM. 2 control and indicator
Adjusts the parameter value for EFFECT 2 in the dual mode
B. MULTI
or the parameter 2 value for the effect in the single (1 or
VO. MULTI
2) mode.
The center position is the default. Turning left decreases
the value while turning right increases the value.
11. EFFECT 2 MIX/PARAM. 3 control and indicator
Adjusts the balance of the output sound from the
OUTPUT 2 jacks on the rear panel in the dual mode.
• Hard left
• Center
• Hard right :DRY 0%, EFFECT 200%
In the single mode, this control adjusts the parameter 3
value for the selected effect type. The center position is
the default. Turning left decreases the value while
turning right increases the value.
12. EFFECT MUTE switch and indicator
Each press of the switch alternates on and off of EFFECT
MUTE. The indicator lights up when the mute is on, while
it turns off when the mute is off.
Note that the dry sound is not muted regardless of the
switch setting.
<NOTE>
When connecting an external foot switch and step-
ping it down, pressing this switch does not alternate
on and off of EFFECT MUTE.
13. POWER switch and indicator
Turns the power on or off. The indicator lights up when
the power is on.
<Hints: About the ADJUST indicators for parameters>
Each ADJUST indicator lights when moving the appro-
priate control after changing the effect type or varia-
tion. This shows that the current position of the con-
trol matches the parameter value.
On the contrary, if you change the effect type or varia-
tion while the indicator is lit, it turns off. This the pa-
rameter is set to the default value.
16
EFFECT 2
VARIATION ADJUST MIX
PARAM.2 PARAM.3
6 DRY+EFF
DELAY 5 7
MISC 4 8
CHO 3 9
10
PITCH 2
DRY EFF
FLANGE 1 1 1
PEAK
10 11
:DRY 100%, EFFECT 0%
:DRY 50%, EFFECT 0%
EFF MUTE
POWER
12 13