Table of Contents
Advertisement
Mega Bar RGBA
1. Plug the fixture in and press the MODE button until "SU.XX" is
displayed. "XX" represents the sound sensitivity level.
2. Use the UP or DOWN buttons to adjust the sound sensitivity.
"SU.00" is off, "SU.01 is the lowest sensitivity, and "SU.31" is the
highest. After adjusting the sound sensitivity, press SET UP if you
wish to activate the Flash mode.
3. "FS.XX" will now be displayed, this is Flash mode. The Flash can
be adjusted between "FS.00" (flash off) to "FS.99" (fastest flash).
Auto Run Mode:
In this mode the Mega Bar RGBA will run a auto program.
1. Plug the fixture in and press the MODE button until "AUTO" is dis-
played.
2. After you have activated Auto Run mode, press the SET UP but-
ton to adjust the fade time.
3. Once you press SET UP "Fd.XX" should be displayed. Use the UP
or DOWN buttons to set the fade speed to either "Fd.00" (fade
off) or between "Fd.01" (fastest speed) and "Fd.99" (slowest
speed). After adjusting the fade speed, press SET UP if you
wish to activate the Flash mode.
4. "FS.XX" will now be displayed, this is Flash mode. The Flash can
be adjusted between "FS.00" (flash off) to "FS.99" (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to
create their own programs tailored to their own individual needs. This
function also allows you to use your fixtures as spot lights. The Mega
Bar RGBA has 7 DMX modes: 4 Channel mode, 6 Channel mode,
7 Channel mode, 9 Channel mode, 10 Channel mode, 18 Channel
mode, and a 34 Channel mode. See pages 13-22 for each modes'
DMX traits.
1. This function will allow you to control each individual fixture's
traits with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"d.XXX" is displayed. "XXX" represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button to select your DMX
Channel mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 9
Operating Instructions
Mega Bar RGBA
modes. The Channel modes are listed below:
To run the 4 Channel Mode, press the MODE button until "Ch.01"
is displayed. This is the 4 Channel DMX Mode.
To run the 6 Channel Mode, press the MODE button until "Ch.02"
is displayed. This is the 2 Channel DMX Mode.
To run the 7 Channel Mode, press the MODE button until "Ch.03"
is displayed. This is the 7 Channel DMX Mode.
To run the 9 Channel Mode, press the MODE button until "Ch.04"
is displayed. This is the 9 Channel DMX Mode.
To run the 10 Channel Mode, press the MODE button until
"Ch.05" is displayed. This is the 10 Channel DMX Mode.
To run the 18 Channel Mode, press the MODE button until
"Ch.06" is displayed. This is the 18 Channel DMX Mode.
To run the 34 Channel Mode, press the MODE button until
"Ch.07" is displayed. This is the 34 Channel DMX Mode.
4. Please see pages 13-22 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX control-
ler.
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings and a Auto program will run.
1. Plug the fixture in and press the MODE and SET UP buttons at the
same time.
ADJ RFC:
This function is used to activate and deactivate the ADJ RFC (Remote
Control). When this function is activated you can control the fixture
using the ADJ RFC. Please see the next page for ADJ RFC controls
and functions.
1. Plug the fixture in and press the MODE button until "Auto" is dis-
played.
2. Press the SET UP button until "rF.XX" is displayed. "XX" repre-
sents either "on" or "oF".
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
ADJ Products, LLC - www.adj.com - Mega Bar RGBA User Manual Page 10
Operating Instructions
Hide quick links:
Advertisement
Table of Contents
