Table of Contents
Advertisement
Mega QA Par38
Static Color Mode:
1. Plug the fixture in and press the MODE button until "CLXX" is dis-
played.
2. There are 15 colors to choose from. Use the UP and DOWN buttons
to scroll through the 15 colors. After you have found your desired
color you can activate strobing by pressing the SET UP button to
enter the Flash (strobe) mode.
3. "FS.XX" will be displayed, this is Flash mode. The Flash can be
adjusted between "FS.00" (flash off) to "FS.15" (fastest flash).
DMX Mode:
Operating through a DMX controller gives the user the freedom to create
their own programs tailored to their own individual needs. This function
also allows you to use your fixtures as spot lights. The Mega QA Par38
has 8 DMX modes: 1 Channel mode, 2 Channel mode, 3 Channel mode,
4 Channel mode, 5 Channel mode, 6 Channel mode, 7 Channel mode
and a 8 Channel mode. See pages 15-20 for each modes' DMX traits.
1. This function will allow you to control each individual fixture's traits
with a standard DMX 512 controller.
2. To run your fixture in DMX mode press the MODE button until
"A.XXX" is displayed. "XXX" represents the current displayed ad-
dress. Use the UP or DOWN buttons to select your desired DMX
address, then press the SETUP button to select your DMX Channel
mode.
3. Use the UP or DOWN buttons to scroll through the DMX Channel
modes. The Channel modes are listed below:
To run the 1 Channel Mode, press the MODE button until "Ch.01"
is displayed. This is the 1 Channel DMX Mode.
To run the 2 Channel Mode, press the MODE button until "Ch.02"
is displayed. This is the 2 Channel DMX Mode.
To run the 3 Channel Mode, press the MODE button until "Ch.03"
is displayed. This is the 3 Channel DMX Mode.
To run the 4 Channel Mode, press the MODE button until "Ch.04"
is displayed. This is the 4 Channel DMX Mode.
To run the 5 Channel Mode, press the MODE button until "Ch.05"
is displayed. This is the 5 Channel DMX Mode.
To run the 6 Channel Mode, press the MODE button until "Ch.06"
is displayed. This is the 6 Channel DMX Mode.
To run the 7 Channel Mode, press the MODE button until "Ch.07"
Operating Instructions
Mega QA Par38
is displayed. This is the 7 Channel DMX Mode.
To run the 8 Channel Mode, press the MODE button until "Ch.08"
is displayed. This is the 8 Channel DMX Mode.
4. Please see pages 15-20 for DMX values and traits.
5. After you have chosen your desired DMX Channel mode plug in
the fixture via the XLR connections to any standard DMX controller.
Default Running Mode:
This is a default running mode. When this mode is activated all modes
will return to their default settings.
1. Plug the fixture in and press the MODE button until "dXX" is dis-
played. "XX" represents either "on" or "oFF".
2. Press the SET UP button until "dEFA" is displayed.
3. Press the UP and DOWN buttons simultaneously. Press the MODE
button to exit.
Infrared Receiver:
This function is used to activate and deactivate the infrared receiver.
When this function is activated you can control the fixture using the ADJ
LED RC 2 (Remote Control). Please see the next page for ADJ LED RC 2
controls and functions.
1. Plug the fixture in and press the MODE button until "dXX" is displayed.
"XX" represents either "on" or "oFF".
2. Press the SET UP button until "IrXX" is displayed. "XX" represents
either "on" or "oF".
3. Press the UP or DOWN buttons to either activate the remote func-
tion (On) or deactivate it (Off).
Operating Instructions
Advertisement
Table of Contents
