American DJ Mini Emerald Beam User Instructions
American DJ Mini Emerald Beam User Instructions

American DJ Mini Emerald Beam User Instructions

Two channel dmx intellingent green laser effect

Advertisement

Quick Links

User Instructions
5/07
American DJ
®
4295 Charter Street
Los Angeles, CA. 90058
www.americandj.com
Mini Emerald Beam™
Unpacking:
Thank you for purchasing the Mini Emerald Beam™ by
American DJ
. Every Mini Emerald Beam™ has been thoroughly tested
®
and has been shipped in perfect operating condition. Carefully check
the shipping carton for damage that may have occurred during ship-
ping. If the carton appears to be damaged, carefully inspect your unit
for any damage and be sure all equipment necessary to operate the
unit has arrived intact. In the event damage has been found or parts
are missing, please contact our toll free customer support number for
further instructions. Please do not return the unit to your dealer without
first contacting customer support.
Introduction:
The Mini Emerald Beam™ is a unique two chan-
nel, DMX intellingent green laser effect that creates several different
effects. This unit can be used as a stand alone, sound-active unit or in
a Master/Slave configuration. The unit can also be controlled via DMX
controller. The unit's sound sensitivity may be adjusted by a sensitivity
knob on the rear of the unit. For best results use fog or special effects
smoke to enhance the beams projections.
Customer Support:
American DJ
support line, to provide set up help and to answer any question should
you encounter problems during your set up or initial operation. You
may also visit us on the web at www.americandj.com for any com-
ments or suggestions. For service related issue please contact Ameri-
can DJ
. Service Hours are Monday through Friday 9:00 a.m. to 5:00
®
p.m. Pacific Standard Time.
Voice:
(800) 322-6337
Fax:
(323) 582-2941
E-mail:
support@americandj.com
To purchase parts online visit http://parts.americandj.com
Caution!
There are no user serviceable parts inside this unit. Do not
attempt any repairs yourself, doing so will void your manufactures
warranty. In the unlikely event your unit may require service please
contact American DJ customer support.
Please recycle the shipping carton when ever possible.
American DJ
- www.americandj.com - Mini Emerald Beam™ Instruction Manual Page 2
©
®
General Introduction
provides a toll free customer
®

Advertisement

Table of Contents
loading

Summary of Contents for American DJ Mini Emerald Beam

  • Page 1 In the unlikely event your unit may require service please contact American DJ customer support. Please recycle the shipping carton when ever possible. American DJ ® 4295 Charter Street Los Angeles, CA. 90058 www.americandj.com 5/07 American DJ - www.americandj.com - Mini Emerald Beam™ Instruction Manual Page 2 © ®...
  • Page 2 Allow about 6” (15cm) between this device and a wall. • Do not attempt to operate this unit, if it becomes damaged. The Mini Emerald Beam™ carries a 90 day limited warranty. Please fill • This unit is intended for indoor use only, use of this product out- out the enclosed warranty card to validate your purchase.
  • Page 3: Warning Labels

    1. XLR Output Jack - This female output jack is used to transmit the incoming DMX signal to another DMX fixture, or transmit a Master/ Slave signal to the next Mini Emerald Beam™ in the chain. For best results in DMX or Master/Slave mode terminate this jack if it is the last unit in the chain.
  • Page 4: Assigning Dmx Address

    The Mini Emerald Beam™ is a two channel DMX unit. The gle controller, as long as all fixtures and the controller are DMX com- DMX address is set on the rear panel of the Mini Emerald Beam.™ pliant. To ensure proper DMX data transmission, when using several Your unit and your DMX controller require a standard 3-pin XLR con- DMX fixtures try to use the shortest cable path possible.
  • Page 5: Power Supply

    1-9 only. Data Compliment (- signal) Pin 2 Pin 2 4. The Mini Emerald Beam™ uses two DMX channels. See page 13 Data True (+ signal) Pin 3 Pin 3 for detailed description of the DMX traits. Use your DMX control- ler to activate the various built-in patterns.
  • Page 6 3. Turn dipswitch #1 to the “ON” position on the SLAVE units, and they will react the same as the MASTER. American DJ - www.americandj.com - Mini Emerald Beam™ Instruction Manual Page 11 American DJ - www.americandj.com - Mini Emerald Beam™ Instruction Manual Page 12 ©...
  • Page 7: Warranty

    American DJ, Inc. concludes, after inspection, affects the reliability of the product; if the product has been repaired or serviced by anyone other than the American DJ, Inc. factory unless prior written authorization was issued to purchaser by American DJ, Inc.; if the...
  • Page 8: Specifications

    ©American DJ® American DJ World Headquarters: 4295 Charter Street Los Angeles, CA 90058 USA Tel: 323-582-2650 / Fax: 323-582-2610 Web: www.americandj.com / E-mail: info@americandj.com American DJ - www.americandj.com - Mini Emerald Beam™ Instruction Manual Page 15 © ®...

Table of Contents