Initial Network Settings - Mitsubishi Electric DLP WD8200LU User Manual

Initial network settings

You can set the network of the projector using the
menu.
1 1 2 2
NETWORK
PROJECTOR NAME
NETWORK PASSWORD
IP CONFIG
NETWORK CERTIFICATION
NETWORK CONTROLLER
NETWORK RESET
Setting Projector Name
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the  or  button to select PROJECTOR
NAME.
PROJECTOR NAME
3. Press the  or  button to select SET .
4. Press the ENTER button.
• PROJECTOR NAME screen appears.
PROJECTOR NAME
CODE : XXXXX
A B C D E F
N O P Q R S
0 1 2 3 4 5
! " # $ % '
OK
5. Press the direction buttons to move the key cursor,
select the characters or marks to enter, and press
the ENTER button.
• Projector Name can be set using up to 15
characters including alphabets (capital/small),
numeric characters, or marks.
← key: ............. Shifting the position of enter
cursor to the left for each
character.
→ key: ............. Shifting the position of enter
cursor to the right for each
character.
DEL key: .......... Deleting the character in the
position of enter cursor for each
character.
caps/CAPS key: Switching an alphabet character
to CAPITAL or small.
NEXT/PREV key: Switching the marks listed on
the fourth line.
SPACE key: ..... Inserting a space in the position
of enter cursor.
CLEAR key: ..... Deleting all the entered
characters.
• You can enter numbers by pressing the number
buttons (0 to 9) while holding down the NUM
button on the remote control.
6. When selecting OK, the setting is completed as the
name stored. However, when selecting CANCEL,
the setting is completed without storing.
opt.
ENTER
ENTER
ON
STANDARD
OK
SET
V Z $ %
← →
G H I J K L M DEL
T U V W X Y Z caps
NEXT
6 7 8 9 – . _
( ) + , / SPACE
*
CLEAR
CANCEL
• The display returns the NETWORK menu after
selecting OK or CANCEL.
• It may take some time to reflect the settings.
Network Password Settings
(See page 32 for menu setting.)
1. Display the NETWORK menu.
2. Press the  or button to select NETWORK
PASSWORD.
NETWORK PASSWORD
3. Press the ENTER button.
• CURRENT NETWORK PASSWORD screen
appears.
CURRENT NETWORK PASSWORD
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
A
N
0
4. Press the direction buttons to move the key cursor,
select the characters or marks to enter, and press
the ENTER button.
• Password can be set using up to 32 characters
including alphabets (capital/small) or numeric
characters.
← key: ............. Shifting the position of enter
→ key: ............. Shifting the position of enter
DEL key: .......... Deleting the character in the
caps/CAPS key: Switching an alphabet character
CLEAR key: ..... Deleting all the entered
• You can enter numbers by pressing the number
buttons (0 to 9) while holding down the NUM
button on the remote control.
• The default password is "admin".
5. Select OK, and NEW NETWORK PASSWORD
screen appears if the entered password is correct.
• If the entered password is not correct,
CURRENT NETWORK PASSWORD screen
appears again.
NEW NETWORK PASSWORD
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
CONFIRM NETWORK PASSWORD
∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗∗
A
N
0
EN-49
ENTER
← →
B C D E F G H I J K L M DEL
O P Q R S T U V W X Y Z caps
1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
cursor to the left for each
character.
cursor to the right for each
character.
position of enter cursor for each
character.
to CAPITAL or small.
characters.
←
B C D E F G H I J K L M DEL
O P Q R S T U V W X Y Z caps
1 2 3 4 5 6 7 8 9 CLEAR
OK CANCEL
→