Monster SUPERTHIN Installation Manual
Small tilt mount
Hide thumbs
Also See for SUPERTHIN:
- Installation manual and warranty (21 pages) ,
- Installation manual and warranty (20 pages)
Related Manuals for Monster SUPERTHIN
Summary of Contents for Monster SUPERTHIN
-
Page 1: Installation Manual
SUPERTHIN Small TIlT mOUNT ™ SECURE, EASY TO INSTALL, LOW PROFILE TILTINg MOUNT INSTallaTION maNUal aNd waRRaNTy –27 " " lbs. (25-68cm) (18.14kg) -
Page 2: Safety Warning
SUPERTHIN Small TIlT mOUNT ™ This SuperThin mount is designed to mount 10"– 27" (25 – 68 cm) flatscreen televisions to vertical walls. Maximum weight capacity is 40 lbs. (18.14 kg). SaFETy waRNING If you don’t understand these directions, or are Before installing, carefully review the instructions to ensure that no parts are missing or defective. - Page 3 4.72" (12.0cm) 1.7" (4.3cm) 2.95" (7.5cm) 3.94" (10.0cm) Specifications and Notes VESA 75×75 / 100×100 Compliant ™ Monster is constantly striving to improve its products. Specifications are subject to change without notice.
-
Page 4: Package Contents
2 Concrete Anchors 2 Lag Bolts 2 Round Washers Screws 4 each M4×15 1 Bubble Level 4 each M5×15 Package Contents If any parts are missing, please call the appropriate Monster number for your location. See page 2 for phone numbers. -
Page 5: Read Before Installing
(5) DO NOT install in a location where there is anchors) are included, masonry mounting requires excessive dust, smoke or moisture. These sources specialized knowledge, skills and tools. Monster can create a fire. highly recommends that you seek the assistance of a professional installer when mounting to masonry. -
Page 6: Required Tools
Above tools from any source of heat or water. Replace ³ ∕ ₁₆ " drill bit with ½" masonry drill bit Hammer TIP: To hide your TV’s power cord and AV cables, install a Monster FlatScreen CleanView Cable ™ ™... - Page 7 Installing the wall mounting Plate Remove all pieces of the wall mounting system to ensure you have all necessary parts. The TV mounting plate and wall mounting plate come assembled in the package. Before installing mount, you must detach the two pieces as follows: Detach the TV mounting plate from the wall mounting plate by loosening the security screws on either side of the wall mounting plate.
- Page 8 wood Stud mounting Using an electronic studfinder, locate a wall stud at your desired mounting location. With the help of another person, position the wall mounting plate on the wall stud.
- Page 9 wood Stud mounting (cont’d) Suspend a straight edge, such as a ruler, across the top of the mounting plate. Place the provided level on the straight edge and confirm that the wall plate is horizontally straight. Hold the plate firmly in place. Mark the stud center in the top and bottom mounting holes with a pencil.
- Page 10 wood Stud mounting (cont’d) With the help of another person, attach the wall plate to the wall using the lag bolts and round washers as shown to the right. Tighten each bolt with your wrench. Turn clockwise until secure. Continue to page 14 to continue your installation. DO NOT over tighten bolts.
- Page 11 Masonry mounting requires specialized knowledge, skills and tools. Monster highly recommends that DO NOT drill holes in masonry you seek the help of a professional installer when mortar joints. mounting to masonry. With the help of a friend, position the mounting plate in the desired location.
- Page 12 masonry mounting (cont’d) With your electric drill and ½" masonry bit, pre-drill a 3" deep hole at each mark. Install the supplied plastic concrete anchors in each hole. Tap into hole with hammer until fully seated. Position the wall mounting plate over the holes drilled in the wall.
- Page 13 masonry mounting (cont’d) With the help of another person, attach the wall plate to the wall using the lag bolts and round washers as shown to the right. Tighten each bolt with your wrench. Turn clockwise until secure. DO NOT over tighten bolts. This can DO NOT release the wall plate until damage the wall plate or the surface of you are absolutely sure it is secured to...
- Page 14 Setting your mount's adjustment Capabilities This mount features all-directional OmniBall ™ for fine-tuning the position of your display. The OmniBall allows you to pivot your screen any direction and rotate it 360°. Before attaching your flatscreen TV to the four-point TV mounting plate, you can increase or decrease the OmniBall pivot action.
- Page 15 Setting your mount's adjustment Capabilities (cont’d) With a socket wrench (13mm or ½"), turn the tension nut clockwise to limit pivot and rotation. Turn the nut counterclockwise to increase pivot and rotation.
- Page 16 attaching your Flatscreen TV to the TV mounting Plate DO NOT lay your TV face down when attaching the TV mounting plate. This The television should be unplugged can cause permanent damage to your before threading any bolt or screw into screen.
- Page 17 Tighten the screw with a Phillips screwdriver. Do not over tighten. Congratulations You’ve successfully installed your Monster SuperThin FlatScreen Mount. ™ Visit us at www.MonsterCable.com/FlatScreen for more innovative Monster FlatScreen products.
- Page 18 Ultra-soft for easy routing and installation. Exclusive Monster MicroFiber cloth won’t scratch delicate screen patented technologies deliver the advanced coatings. performance you need from your flatscreen TV. For more details on all our Monster FlatScreen products, visit us at MonsterCable.com/FlatScreen...
-
Page 19: Limited Warranty For Consumers
(including without transferred ownership of the Product, whichever occurs limitation building and/or electrical codes), (iv) in earlier. Also, You must call Monster and obtain a Return accordance with manufacturer recommendations and / Authorization Number (as described under “How to or instructions in the materials and documentation that Make a Claim”) within two (2) months after You discover... - Page 20 English and other versions of this Limited Warranty, the instructed on how to properly submit the estimate and English version shall prevail. the resulting invoice to Monster for payment. Any fees for repairs may be negotiated by Monster. REGISTRATION. Please register Your Product at www.monstercable.com.