Sony SRS-RF90R Operating Instructions

3-236-404-12(1)
Wireless Stereo
Speaker System
Operating Instructions
Mode d'emploi
Manual de instrucciones
Owner's Record
The model number is located at the bottom of the transmitter and the speaker
system.
The serial number is located at the bottom of the transmitter and the speaker
system.
Record these numbers in the spaces provided below. Refer to them whenever
you call upon your Sony dealer regarding this product.
Model No.
Transmitter
Speaker system
Serial No.
Transmitter
Speaker system
SRS-RF90RK
SRS-RF90R
Sony Corporation © 2002
Printed in Korea
English
WARNING Welcome!
To prevent fire or shock hazard, do not expose
Thank you for purchasing the Sony
the unit to rain or moisture.
SRS-RF90RK/RF90R Wireless Stereo Speaker
To avoid electrical shock, do not open the
System. Before operating the unit, please read this
cabinet. Refer servicing to qualified personnel
manual thoroughly and retain it for future reference.
only.
Some features are:
Information
• Wireless system that allows you to use your
You are cautioned that any changes or modifications
system free from the restriction of speaker cords.
not expressly approved in this manual could void
• Wide signal reception range up to about 150 feet
your authority to operate this equipment.
(46 m).
For the Customers in the U.S.A.
• 3 Channel options on transmitter for optimum
If you have any questions about this product, you
signal reception.
may call:
• Auto tuning function available on speaker.
Sony Direct Response Center 1-(800)-222-7669
• Reflector attached on the speaker system creates
or write to:
a high fidelity sound field.
Sony Direct Response Center 12451 Gateway
• The one-box stereo type structure produces a
Blvd.Fort Myers, FL 33913
wide soundstage.
Declaration of Conformity
• This speaker system can be powered two ways;
Trade Name: SONY
you can use the supplied AC power adaptor or
Model No.: SRS-RF90R
(Speaker Unit) built-in rechargeable battery.
Responsible Party: Sony Electronics Inc. • Novel and unconventional design with blue-
Address: 680 Kinderkamack Road,
illumination for an attractive showpiece in any
Oradell, NJ 07649 USA
room.
Telephone No.: 201-930-6972
This device complies with Part 15 of the FCC
Rules. Operation is subject to the following two Notes on receiving
conditions: (1) This device may not cause
performance
harmful interference, and (2) this device must
accept any interference received, including
interference that may cause undesired operation.
The system for this equipment utilizes very high
frequency signals in the 900 MHz band so the
For the Customers in Canada
receiving performance may deteriorate due to the
Operation is subject to the following two surroundings. The following examples illustrate
conditions: (1) this device may not cause conditions that may reduce the possible receiving
interference, and (2) this device must accept any range or cause interference with reception.
interference, including interference that may cause • Inside a building with walls containing steel
undesired operation of the device. beams.
• Area with many steel file cabinets, etc.
RECYCLING NICKEL CADMIUM BATTERIES
• Area with many electrical appliances capable of
generating electromagnetic noise.
Nickel Cadmium batteries
• Transmitter is placed on a metal instrument.
are recyclable.
• Area facing roadways.
You can help preserve our
• Noise or interfering signals exist in the
environment by returning
surroundings due to radio transceivers in trucks,
your used rechargeable
etc.
batteries to the collection and
• Noise or interfering signals exist in the
recycling location nearest
surroundings due to wireless communication
you.
systems installed along roadways.
Note: In some areas the disposal of Nickel
• Transmitter is placed directly on floor.
Cadmium batteries in household or
Placing it up off the floor, such as on a desk, is
business trash may be prohibited.
recommended.
For more information regarding recycling of
rechargeable batteries, call toll free 1-800-822-
8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking
Nickel Cadmium batteries.
C To connect to TV, etc.
N Getting started
If noise occurs when the transmitter is
connected to the headphone jack of your
Unpacking
TV or VCR, set the NOISE FILTER switch
to ON.
Check that you have the following items:
• The speaker system
to AUDIO IN
Transmitter
• The transmitter (SRS-RF90RK only)
A jack
• AC power adaptor
(2 for SRS-RF90RK) (1 for SRS-RF90R)
• Connecting cord (phono plugs y stereo mini
plug), 1 m (SRS-RF90RK only) OFF ON B R A L DC IN 9V 1 2 3
NOISE FILTER AUDIO IN CHANNEL
Right channel Left channel
Hooking up the system
(red) (white)
Attaching the supplied reflector to
the speaker system
Insert the plugs until its base is settled firmly as Connecting cord
illustrated. (supplied)
to stereo mini jack
TV, etc.
Notes
• If you connect the transmitter to LINE OUT or REC
Connecting the transmitter to audio/ OUT jack, do not set the NOISE FILTER switch to
ON. Otherwise, the volume will be limited.
video equipment
• The NOISE FILTER switch effects the sound only in
case of such as connection diagram C. In diagrams
For customers buying the SRS-RF90R
A and B, the switch has no effect.
You can use the transmitter supplied with the
• When the transmitter is placed on or near a TV, it
MDR-RF915RK or MDR-RF945RK. If you have
may pick up a noise. In such case, place the
already set the transmitter, the following hookup
transmitter away from the TV.
of the transmitter is not required. However, you
Connecting the transmitter to an AC
cannot use a transmitter supplied with a cordless/
wireless headphone system other than the above outlet using the supplied AC power
models.
adaptor
For customers buying the SRS-RF90RK
Set the transmitter by the following steps. Select
Transmitter
the hookup depending on the jack type of the
audio/video equipment you want to connect the
To DC IN
transmitter to.
9 V jack
to an AC outlet
A To connect to a LINE OUT or REC OUT
AC power adaptor
(supplied: AC-S901)
Transmitter
Notes
• Use only the supplied AC power adaptor. Do not use
any other AC power adaptor.
B R A L DC IN 9V 1 2 3
OFF ON AUDIO IN
NOISE FILTER CHANNEL
to AUDIO IN
Polarity of the plug
B jack
• When you connect the connecting cord directly to an
earphone jack, the audio signal will not be output
through the right channel. In such a case, use the
separately sold PC-236MS plug adaptor.
Connecting cord • If the connected equipment has the AVLS (Automatic
(supplied)
Volume Limiter System) function, be sure to turn the
function off when using the transmitter. Otherwise, you
will have to turn up the volume of the speaker system,
and that may cause noise.
• If the connected equipment has the BASS BOOST or
Left channel Right channel
MEGA BASS function, be sure to turn the function off
(white) (red)
when using the transmitter. Otherwise, the sound from
the speaker system may be distorted.
to LINE OUT or REC • Do not place the transmitter near a fluorescent lamp, etc.
OUT jacks when using the system.
* WALKMAN is a registered trademark of Sony
Corporation.
Stereo system, VCR, etc.
The effective areas of the
B To connect to headphones jack
transmitter
The optimum distance is up to approximately 150
Transmitter
feet (46 m) without the system picking up some
interference. However, the distance may vary
to AUDIO IN
according to the surroundings and environment. If
A jacks
the system picks up some noise while using it
within the above mentioned distance, reduce the
distance between the transmitter unit and the
B R A L DC IN 9V
OFF ON 1 2 3 speaker system, or select another channel.
NOISE FILTER AUDIO IN CHANNEL
Notes
Right channel Left channel • When you use the speaker system inside the effective
areas of the transmitter, the transmitter can be placed in
(red) (white)
any direction from the listener.
• Even within the signal reception area, there are some
spots (dead spot) where the RF signal cannot be
received. This is a characteristic inherent to RF signals,
Connecting cord
and does not indicate malfunction. By slightly moving
(supplied)
the transmitter, location of the dead spot can be
changed.
Charging the speaker
system battery
to headphones
Unimatch plug
or LINE OUT jack
adaptor (not Using the speaker system for the first
(stereo mini jack)
supplied)
time
Discman, MD,
to headphones When you use the system for the first time, charge
WALKMAN*, VCR,
jack (stereo the battery in the following manner.
etc.
phone jack) 1
Connect the speaker system to a power
source.
Tweeter Tweeter
(right) (left)
AC power adaptor (supplied)
To an AC
outlet
2
The CHARGE indicator on the speaker
Disposing of the
system will light up to indicate that the
battery is being charged.
speaker system
Be sure to remove the built-in rechargeable
batteries from the speaker system before you
dispose of the speaker system.
1
Remove 13 screws from the speaker
system using a cross-point screw driver
as illustrated below.
CHARGE indicator
Notes
• It takes about 28 hours to fully charge an empty battery.
• Charge the rechargeable battery within a temperature of
0 ˚C to 35 ˚C (32 ˚F to 95 ˚F).
• If you turn on the speaker system while charging the
battery, battery charging stops and the CHARGE
indicator turns off. You can use the speaker system by
the power from the AC adaptor.
• The duration time of the rechargeable battery is about 4
hours. If the light of the reflector becomes weak, it
means the rechargeable battery is low. So, turn off the
2
speaker system and charge the battery.
Open the cabinet of the speaker system
• Even after battery charging is finished, the CHARGE
and remove the one screw to remove the
indicator always lights up.
• The life of the built-in rechargeable battery is about 3 rechargeable battery as illustrated.
years. But it differs depending on operating conditions.
• Use only the supplied AC power adaptor. Do not use Battery
any other AC power adaptor.
N Operating the system
Listening to a program
Before using the speaker system, charge the built-
in rechargeable battery first.
Turn down the volume of the speaker system
before playing back a program on the connected N Additional information
audio/video equipment.
OFF y ON Precautions
The switch of the
reflector light
• When the transmitter is not to be used for a long
period of time, disconnect the AC power
High
adaptor from the AC outlet holding the plug. Do
TUNING
not pull on the cord.
button
VOLUME control
Notes on the location you set the speaker
POWER switch
POWER indicator Low system
• Do not leave the wireless speaker system in a
1
First turn on the audio/video equipment location subject to:
– Direct sunlight or extremely high temperature such
and start playing.
as near a heater or in a car with its windows closed.
The power indicator of the transmitter
– High humidity such as in a bathroom.
will light up. – Excessive dust or sandy places.
– The speaker system is magnetically shielded, but do
2
not put a recorded tape, watch, cash card or floppy
Turn on the speaker system.
disk in front of the speaker system.
The power indicator of the speaker
• Set up the speaker system on a flat surface.
system will light in red.
• Depending on where you set the speaker
system, it may fall down. Do not leave valuables
3
Select the radio frequency with the near the speaker system.
CHANNEL selector.
Notes on charging the battery
• When you charge the rechargeable battery, use
the supplied AC adaptor only.
• The charging time differs depending on usage
conditions of the battery.
1 2 3
CHANNEL
• When you use the battery for the first time or the
battery is not to be used for a long time, the
battery duration time may become shorter than
Note
the usual duration time. However, after you
If you use the unit near a cordless telephone, it may
cause radio interference. If poor reception occurs, try charge the battery several times, the battery
another channel using the CHANNEL selector. duration time returns to its normal condition.
4 • If the battery duration time becomes half of its
Turn up the volume to a moderate level
normal time even after the battery is charged
with the VOL control.
fully, the battery is worn out. In this case,
Press the TUNING button briefly for consult your nearest Sony dealer.
automatic tuning of the speaker system.
Notes on using the speaker system
If you do not receive a clear audio signal,
• Do not disassemble the speaker unit, built-in
press it again.
amplifier or cabinet.
• Do not insert an object into the jack. Doing so
Sending RF signals from the Transmitter
may cause a malfunction.
The transmitter starts sending the RF signals
• Keep the volume at a moderate level to prevent
automatically, when it detects audio signals from
distortion.
the equipment connected.
If it does not detect an audio signal for more than • Do not carry the speaker unit by its reflector. If
approximately four minutes, the transmitter will you do so, the speaker system may detach from
stop sending RF signals, and the power indicator
the reflector.
turns off.
Note on cleaning
When the transmitter receives an audio signal
Clean the cabinet of the speaker system with a soft
again, it starts sending the RF signals, and the
cloth slightly moistened with water or a mild
power indicator will light in red again.
If the audio signal is very weak, the transmitter detergent solution. Do not use any type of abrasive
does not send RF signals. If the transmitter is pad, scouring powder or solvent such as alcohol or
connected to a headphone jack, make sure the benzene as it may mar the finish of the cabinet.
volume of the equipment connected is set to 5 – 6
When the color of your monitor screen
or higher.
becomes irregular
You may not hear the beginning of the sound from
the speaker system until the transmitter starts Because this speaker system is magnetically
sending the RF signals after detecting an audio shielded, you can set it up near a monitor. But
depending on the model of the monitor, color
signal.
irregularity may occur.
Note
To correct the color irregular
If the transmitter is connected to the headphones jack of
Turn off the monitor, and then turn it on again
the source equipment, set the volume of that equipment as
after 15 to 30 minutes.
high as possible without distorting the audio signal.
Using the Built-in Rechargeable Batteries
If color irregularity remains after
The built-in rechargeable batteries allow you to use
performing the above
the unit anywhere.
• Separate the monitor and the speaker system.
Remove the supplied AC power adaptor from the
• Make sure that no magnetic object, such as may
DC IN jack of the unit to use the built-in
be attached to a door of shelf, healthcare device
rechargeable batteries.
or toys, etc., is located near the speaker system.
To use the illumination of the reflector
If you have any questions or problems concerning
Turn on the switch of the reflector light.
the system that are not covered in this manual,
Notes please consult your nearest Sony dealer.
• If a hissing noise is heard, move it closer to the
Be sure to bring the speaker system and the
transmitter.
• If you turn up the volume of the speaker system too transmitter to the Sony dealer when requiring
high, the light of the reflector may flicker. But this is not
repair work.
a malfunction.
• If you hold the antenna of the transmitter with your
hand, noise may occur. But this is not a malfunction.
Français
Troubleshooting
AVERTISSEMENT
No sound/Muffled sound
Pour éviter tout risque d'incendie ou
, Check the connection of the audio/video
d'électrocution, ne pas exposer cet appareil à la
equipment.
pluie ou à l'humidité.
, Check that the audio/video equipment is turned
Pour prévenir tout risque d'électrocution,
on.
n'ouvrez jamais le coffret. Adressez-vous à un
, Turn up the volume on the connected audio/
personnel qualifié uniquement pour toute
video equipment, if the transmitter is connected
intervention sur l'appareil.
to the headphones jack.
, Change the radio frequency with the CHANNEL
Avertissement
selector on the transmitter, then press the
Soyez avisé que toute modification non
TUNING button again.
expressément approuvée dans le présent mode
, The speaker system's POWER indicator light is d'emploi pourrait entraîner l'annulation de vos
weak or turned off. droits d'utilisation de ce produit.
• Charge the built-in rechargeable battery or if the
POWER indicator is still off after charging the Pour les utilisateurs au Canada
built-in rechargeable battery, take the speaker Son utilisation est autorisée seulement aux
system to a Sony dealer for replacement of the conditions suivantes: (1) il ne doit pas produire de
rechargeable battery. brouillage et (2) l'utilisateur du dispositif doit être
, If you connect the transmitter to the LINE OUT or prêt à accepter tout brouillage radioeléctrique reçu,
REC OUT jack of an audio reproducer, make sure
même si ce brouillage est susceptible de
that the NOISE FILTER switch is set to OFF.
compromettre le fonctionnement du dispositif.
, Make sure that the NOISE FILTER switch is set to
either ON or OFF (If the switch gets stuck
between ON and OFF, the sound will be cut off).
RECYCLAGE DES PILES AU NICKEL-CADMIUM
Distortion
Les piles au nickel-cadmium
sont recyclables.
, If the transmitter is connected to the headphones
jack, turn down the volume of the connected Vous pouvez contribuer à
audio/video equipment. If the connected audio/ préserver l'environnement
video equipment has bass boost function, set its en rapportant les piles usées
function to OFF. dans un point de collection
, If the connected audio/video equipment has a et recyclage le plus proche.
LINE OUT jack, connect its LINE OUT jack. Remarque: Dans certain pays, il est interdit de
, Change the radio frequency with the CHANNEL jeter les piles au nickel-cadmium
selector on the transmitter.
avec les ordures ménagères ou dans
, The speaker system's POWER indicator light is
les poubelles de bureau.
weak or turned off.
• Charge the built-in rechargeable battery or if the
Pour plus d'informations sur le recyclage des
POWER indicator is still off after charging the
accumulateurs, téléphonez le numéro gratuit
built-in rechargeable battery, take the speaker
1-800-822-8837 (Etats-Units et Canada
system to a Sony dealer for replacement of the
uniquement), ou visitez http://www.rbrc.org/
rechargeable battery.
, If you connect the transmitter to LINE OUT or
Avertissment: Ne pas utilliser des piles au
REC OUT jack of an audio reproducer, make sure
nickel-cadmium qui sont
that the NOISE FILTER switch is set to OFF.
endommagées ou qui fuient.
Loud background noise
, Move closer to the transmitter. As you move
away from the transmitter, more noise is likely to
Bienvenue !
be heard.
, If the transmitter is connected to the headphones
Nous vous remercions d'avoir fait l'acquisition du
jack, turn up the volume of the connected audio/
système d'enceinte stéréo sans fil SRS-RF90RK/
video equipment.
RF90R de Sony. Avant de faire fonctionner cet
, Change the radio frequency with the CHANNEL
selector on the transmitter, then press the appareil, lisez attentivement le présent mode
TUNING button again. d'emploi et conservez-le pour toute référence
, The speaker system's POWER indicator light is ultérieure.
weak or turned off. Cet appareil offre, entre autres, les caractéristiques
• Charge the built-in rechargeable battery or if the
suivantes :
POWER indicator is still off after charging the
• Système sans fil vous permettant l'utilisation
built-in rechargeable battery, take the speaker
sans fils d'enceinte encombrants.
system to a Sony dealer for replacement of the
• Longue portée de transmission des signaux allant
rechargeable battery.
jusqu'à environ 46 m (150 pi).
, If you connect the transmitter to the LINE OUT or
REC OUT jack of an audio reproducer, make sure • Trois options de canaux de transmission
that the NOISE FILTER switch is set to OFF.
permettant une réception optimale des signaux.
• Fonction de syntonisation automatique à
The battery duration time is short
l'enceinte.
, If you use the battery under the temperature
• Réflecteur fixé au système d'enceinte offrant une
lower than 0 ˚C (32 ˚F), this is not a malfunction.
reproduction sonore haute fidélité.
, The battery life may end. If the battery duration
• Construction stéréo à boîtier unique offrant un
time becomes half of its normal time even after
large champ sonore.
the battery is charged fully, consult your nearest
Sony dealer • Deux possibilités d'alimentation : avec
l'adaptateur CA fourni ou la batterie
rechargeable intégrée.
Specifications
• Conception novatrice et originale avec éclairage
bleu, un design élégant qui convient bien au
General
décor de n'importe quelle pièce.
Carrier frequency 913.5 – 914.5 MHz
Channel Ch1, Ch2, Ch3
Modulation FM stereo
Remarques sur la
Transmitter (SRS-RF90RK only)
qualité de
Power source DC 9 V: supplied AC power adaptor
(AC-S901)
transmission
Audio input phono jacks/stereo mini jack
Input impedance 33 k /51 switchable
Comme le système de cet appareil utilise des
Dimensions Approx. 136 100 136 mm
signaux de très haute fréquence dans la bande des
(6 4 1 / 6 in.) (w/h/d)
3
900 MHz, l'environnement de l'appareil peut
Mass Approx. 146 g (5.2 oz.)
entraîner une détérioration de la qualité de
Speaker system SRS-RF90RK, SRS-RF90R transmission. Les exemples suivants illustrent les
Speaker system 2 way magnetically shielded situations pouvant réduire la plage de
Enclosure type Bass reflex
transmission et perturber la réception.
Speaker units tweeter: 30 mm 2
• Utilisation à l'intérieur d'un bâtiment à structure
woofer: 57 mm 1
en acier.
Power source DC 9 V: supplied AC adaptor (AC-S906T)
• Utilisation dans des pièces contenant de
Rated output Built in amplifiers total 4W (while
nombreux classeurs ou autres éléments en acier.
using the supplied AC adaptor)
• Utilisation à proximité d'un grand nombre
* power output:
d'appareils électriques générant des parasites
Tweeter: 0.25W + 0.25W < 10%
électromagnétiques.
T.H.D., 5 kHz 24 ohms
• Installation du transmetteur sur un instrument
Woofer: 3.5W < 10% T.H.D., 1kHz
métallique.
6 ohms
• Utilisation à proximité d'une route.
Dimensions Approx. 234 300 126 mm
( 9 1 / 11 7 / 5 in.) (w/h/d) • Parasites ou interférences autour de l'appareil,
4 8
Mass Approx. 905 g (31.9 oz.) incl. provenant d'émetteurs-récepteurs de camions
built-in rechargeable battery ou d'autres appareils.
• Parasites ou interférences autour de l'appareil,
Built-in Ni-Cd rechargeable battery
provenant de systèmes de communication sans
Voltage 7.2 V
fil installés le long des routes.
Capacity 700 mAh
• Installation du transmetteur directement sur le
Duration time Approx. 4 hours
sol. Il est recommandé d'installer le
(with the 10 mW reflector light OFF)
transmetteur en hauteur, par exemple sur un
bureau.
Charging time Approx. 28 hours (from fully
discharged to fully charged)
Supplied accessory
The transmitter (SRS-RF90RK only)
AC adaptor (2 for SRS-RF90RK) (1 for SRS-RF90R)
Connecting cord phono plug-stereo miniplug (1m) (1)
(SRS-RF90RK only)
Operating instructions (1)
Optional accessory
Plug adaptor PC-236MS (stereo mini jack y
monaural mini plug)
Design and specifications are subject to change without notice.
C Raccordement à un téléviseur ou à un
N Préparatifs
autre appareil.
Si des parasites sont audibles lorsque le
Déballage
transmetteur est relié à la prise de casque
de votre téléviseur ou magnétoscope,
Vérifiez que vous disposez de tous les éléments
réglez le commutateur NOISE FILTER à
suivants :
ON.
• Système d'enceinte
• Transmetteur (SRS-RF90RK uniquement)
Vers les prises
Transmetteur
• Adaptateur CA
AUDIO IN A
(deux pour le SRS-RF90RK) ou (un pour le
SRS-RF90R)
• Câble de liaison (prises phono y mini-fiche
OFF ON B R A L DC IN 9V 1 2 3
stéréo), 1 m (SRS-RF90RK uniquement) NOISE FILTER AUDIO IN CHANNEL
Canal droit Canal gauche
Raccordement du
(rouge) (blanc)
système
Raccordement du réflecteur fourni au
système d'enceinte Câble de liaison
(fourni)
Insérez les fiches solidement et jusqu'au fond, tel
qu'illustré.
Vers la mini-prise
stéréo
Téléviseur ou
autre appareil
Remarques
• Si vous raccordez le transmetteur à une prise LINE
OUT ou REC OUT, ne réglez pas le commutateur
NOISE FILTER à ON, sinon le volume sera limité.
Raccordement du transmetteur à un
• Le commutateur NOISE FILTER n'agit sur le son
appareil audio ou vidéo que dans les cas ou le raccordement du schéma C
est utilisé. Dans les cas où le raccordement A ou B
Pour les propriétaires du SRS-RF90R est utilisé, il n'a aucun effet.
Vous pouvez utiliser le transmetteur fourni soit • Placé près d'un téléviseur, le transmetteur risque de
subir des interférences. Le cas échéant, éloignez-le
avec le MDR-RF915RK, soit avec le MDR-
du téléviseur.
RF945RK. Si vous avez déjà installé le
transmetteur, il n'est pas nécessaire d'effectuer le
Raccordement du transmetteur à une
raccordement suivant. Cependant, vous ne pouvez
prise de courant à l'aide de
pas utiliser un transmetteur fourni avec un
l'adaptateur CA fourni.
système de casque d'écoute sans fil d'un modèle
autre que ceux cités ci-dessus.
Pour les propriétaires du SRS-RF90RK
Transmetteur
Installez le transmetteur en effectuant les étapes
suivantes. Choisissez le raccordement à effectuer
Vers la
selon le type de prise de l'appareil audio ou vidéo prise
auquel vous souhaitez raccorder le transmetteur. DC IN 9 V
Vers une prise
CA
A Raccordement à une prise LINE OUT ou Adaptateur CA
(fourni : AC-S901 )
REC OUT
Remarques
• Utilisez uniquement l'adaptateur CA fourni. N'utilisez
aucun autre adaptateur CA.
Transmetteur
Polarité de la fiche
B R A L DC IN 9V
OFF ON 1 2 3
NOISE FILTER AUDIO IN CHANNEL
• Lorsque vous raccordez directement le câble de liaison à
Vers la prise
une prise de casque, le signal audio n'est pas émis par le
AUDIO IN B
canal droit. Dans ce cas, utilisez l'adaptateur de fiche
PC-236MS vendu séparément.
• Si l'appareil raccordé est équipé de la fonction AVLS
(système de limitation automatique du volume),
désactivez cette fonction lorsque vous utilisez le
Câble de liaison
transmetteur. Sinon, vous devrez augmenter le volume
(fourni) du système d'enceinte, ce qui pourrait engendrer des
parasites.
• Si l'appareil raccordé est équipé de la fonction BASS
BOOST ou MEGA BASS (amplification des graves,
désactivez cette fonction lorsque vous utilisez le
Canal gauche Canal droit
transmetteur. Sinon, le son provenant du système
(blanc) (rouge)
d'enceinte risque d'être déformé.
• N'installez pas le transmetteur près d'une lampe
Vers les prises LINE fluorescente, etc. lorsque vous utilisez le système.
OUT ou REC OUT
* WALKMAN est une marque déposée de Sony
Corporation.
Chaîne stéréo,
Portée du transmetteur
magnétoscope, etc.
La portée optimale du transmetteur est de 46 m
B Raccordement à une prise de casque (150 pi) environ sans que le système ne capte
d'interférences. Cependant, cette distance peut
Transmetteur varier selon l'environnement de l'appareil. Si le
système capte des parasites alors qu'il est utilisé
Vers les prises
dans la zone définie ci-dessus, rapprochez le
AUDIO IN A
transmetteur et le système d'enceinte ou
sélectionnez un autre canal.
Remarques
B R A L DC IN 9V 1 2 3
OFF ON AUDIO IN
NOISE FILTER CHANNEL
• Quand vous utilisez le système d'enceinte dans la zone
de couverture du transmetteur, la direction du
transmetteur par rapport à l'auditeur n'importe pas.
Canal droit Canal gauche
• Dans la zone de réception des signaux, il existe
(rouge) (blanc)
cependant certains endroits (zones de silence) où la
réception des signaux RF est impossible. Il s'agit d'une
caractéristique inhérente aux signaux RF et n'indique
pas un problème de fonctionnement. Il est possible de
Câble de liaison
modifier l'emplacement de la zone de silence en
(fourni)
déplaçant légèrement le transmetteur.
Recharge de la batterie
du système d'enceinte
Première utilisation du système
Vers la prise de
Adaptateur de
casque ou LINE OUT
fiche universel d'enceinte
(mini-prise stéréo)
(non fourni) Lorsque vous utilisez le système pour la première
Discman, MD,
fois, chargez la batterie tel qu'indiqué ci-dessous.
Vers la prise de
WALKMAN*,
1
casque (prise magnétoscope, etc. Raccordez le système d'enceinte à une
stéréo)
source d'alimentation.
Haut-parleur des
Haut-parleur
des aiguës aiguës (gauche)
(droit)
Adaptateur CA (fourni)
Vers une prise CA
Voir page suivante