Sony SRS-RF90R Operating Instructions

3-236-404-14(1)
Wireless Stereo
Speaker System
Operating Instructions
Mode d'emploi
Manual de instrucciones
Owner's Record
The model number is located at the bottom of the transmitter and the speaker
system.
The serial number is located at the bottom of the transmitter and the speaker
system.
Record these numbers in the spaces provided below. Refer to them whenever
you call upon your Sony dealer regarding this product.
Model No.
Transmitter
Speaker system
Serial No.
Transmitter
Speaker system
SRS-RF90RK
SRS-RF90R
© 2002 Sony Corporation
Printed in Korea
English
WARNING Welcome!
To prevent fire or shock hazard, do not expose
Thank you for purchasing the Sony
the unit to rain or moisture.
SRS-RF90RK/RF90R Wireless Stereo Speaker
To avoid electrical shock, do not open the
System. Before operating the unit, please read this
cabinet. Refer servicing to qualified personnel
manual thoroughly and retain it for future reference.
only.
Some features are:
Information
• Wireless system that allows you to use your
You are cautioned that any changes or modifications
system free from the restriction of speaker cords.
not expressly approved in this manual could void
• Wide signal reception range up to about 150 feet
your authority to operate this equipment.
(46 m).
For the Customers in the U.S.A.
• 3 Channel options on transmitter for optimum
If you have any questions about this product, you
signal reception.
may call;
• Auto tuning function available on speaker.
Sony Customer Informaion Services Center
1-800-222-7669 or http://www.sony.com/ • Reflector attached on the speaker system creates
a high fidelity sound field.
Declaration of Conformity • The one-box stereo type structure produces a
Trade Name: SONY wide soundstage.
Model No.: SRS-RF90R
• This speaker system can be powered two ways;
(Speaker Unit)
you can use the supplied AC power adaptor or
Responsible Party: Sony Electronics Inc.
Address: 16450 W. Bernardo Dr, built-in rechargeable battery.
San Diego, CA 92127 USA • Novel and unconventional design with blue-
Telephone No.: 858-942-2230
illumination for an attractive showpiece in any
This device complies with Part 15 of the FCC
room.
Rules. Operation is subject to the following two
conditions: (1) This device may not cause
harmful interference, and (2) this device must Notes on receiving
accept any interference received, including
interference that may cause undesired operation. performance
The system for this equipment utilizes very high
For the Customers in Canada
frequency signals in the 900 MHz band so the
Operation is subject to the following two
receiving performance may deteriorate due to the
conditions: (1) this device may not cause
surroundings. The following examples illustrate
interference, and (2) this device must accept any
conditions that may reduce the possible receiving
interference, including interference that may cause
range or cause interference with reception.
undesired operation of the device.
• Inside a building with walls containing steel
beams.
For the customers in the USA and Canada
• Area with many steel file cabinets, etc.
• Area with many electrical appliances capable of
RECYCLING NICKEL METAL HYDRIDE
generating electromagnetic noise.
BATTERIES
• Transmitter is placed on a metal instrument.
• Area facing roadways.
Nickel Metal Hydride • Noise or interfering signals exist in the
batteries are recyclable. surroundings due to radio transceivers in trucks,
You can help preserve our etc.
environment by returning • Noise or interfering signals exist in the
your used rechargeable surroundings due to wireless communication
batteries to the collection and
systems installed along roadways.
recycling location nearest you.
• Transmitter is placed directly on floor.
Placing it up off the floor, such as on a desk, is
For more information regarding recycling of recommended.
rechargeable batteries, call toll free
1-800-822-8837, or visit http://www.rbrc.org/
Caution: Do not handle damaged or leaking
Nickel Metal Hydride batteries.
C To connect to TV, etc.
N Getting started
If noise occurs when the transmitter is
connected to the headphone jack of your
Unpacking
TV or VCR, set the NOISE FILTER switch
Check that you have the following items: to ON.
• The speaker system
to AUDIO IN
Transmitter
• The transmitter (SRS-RF90RK only)
A jack
• AC power adaptor
(2 for SRS-RF90RK) (1 for SRS-RF90R)
• Connecting cord (phono plugs y stereo mini
plug), 1 m (SRS-RF90RK only) B R A L DC IN 9V 1 2 3
OFF ON
NOISE FILTER AUDIO IN CHANNEL
Right channel
Left channel
Hooking up the system
(red) (white)
Attaching the supplied reflector to
the speaker system
Insert the plugs until its base is settled firmly as
Connecting cord
illustrated. (supplied)
to stereo mini jack
TV, etc.
Notes
• If you connect the transmitter to LINE OUT or REC
OUT jack, do not set the NOISE FILTER switch to
Connecting the transmitter to audio/
ON. Otherwise, the volume will be limited.
video equipment
• The NOISE FILTER switch effects the sound only in
case of such as connection diagram C. In diagrams
For customers buying the SRS-RF90R
A and B, the switch has no effect.
You can use the transmitter supplied with the
• When the transmitter is placed on or near a TV, it
MDR-RF915RK or MDR-RF945RK. If you have
may pick up a noise. In such case, place the
already set the transmitter, the following hookup
transmitter away from the TV.
of the transmitter is not required. However, you
Connecting the transmitter to an AC
cannot use a transmitter supplied with a cordless/
wireless headphone system other than the above outlet using the supplied AC power
models.
adaptor
For customers buying the SRS-RF90RK
Set the transmitter by the following steps. Select
Transmitter
the hookup depending on the jack type of the
audio/video equipment you want to connect the
To DC IN
transmitter to.
9 V jack
to an AC outlet
A To connect to a LINE OUT or REC OUT
AC power adaptor
(supplied: AC-S901)
Transmitter
Notes
• Use only the supplied AC power adaptor. Do not use
any other AC power adaptor.
B R A L DC IN 9V
OFF ON 1 2 3
NOISE FILTER AUDIO IN CHANNEL
to AUDIO IN
Polarity of the plug
B jack
• When you connect the connecting cord directly to an
earphone jack, the audio signal will not be output
through the right channel. In such a case, use the
separately sold PC-236MS plug adaptor.
Connecting cord • If the connected equipment has the AVLS (Automatic
(supplied) Volume Limiter System) function, be sure to turn the
function off when using the transmitter. Otherwise, you
will have to turn up the volume of the speaker system,
and that may cause noise.
• If the connected equipment has the BASS BOOST or
Left channel Right channel
MEGA BASS function, be sure to turn the function off
(white) (red)
when using the transmitter. Otherwise, the sound from
the speaker system may be distorted.
to LINE OUT or REC • Do not place the transmitter near a fluorescent lamp, etc.
OUT jacks
when using the system.
* "WALKMAN" is a registered trademark of Sony
Stereo system, VCR, etc. Corporation to represent Headphone Stereo products.
The effective areas of the
B To connect to headphones jack
transmitter
The optimum distance is up to approximately 150
Transmitter
feet (46 m) without the system picking up some
interference. However, the distance may vary
to AUDIO IN
according to the surroundings and environment. If
A jacks
the system picks up some noise while using it
within the above mentioned distance, reduce the
distance between the transmitter unit and the
OFF ON B R A L DC IN 9V 1 2 3 speaker system, or select another channel.
NOISE FILTER AUDIO IN CHANNEL
Notes
Right channel Left channel • When you use the speaker system inside the effective
(red) (white) areas of the transmitter, the transmitter can be placed in
any direction from the listener.
• Even within the signal reception area, there are some
spots (dead spot) where the RF signal cannot be
received. This is a characteristic inherent to RF signals,
Connecting cord
and does not indicate malfunction. By slightly moving
(supplied)
the transmitter, location of the dead spot can be
changed.
Charging the speaker
system battery
to headphones
Unimatch plug
or LINE OUT jack
adaptor (not Using the speaker system for the first
(stereo mini jack)
supplied)
time
Discman, MD,
When you use the system for the first time, charge
to headphones
WALKMAN*, VCR,
jack (stereo the battery in the following manner.
etc.
phone jack)
1
Connect the speaker system to a power
source.
Tweeter
Tweeter
(right) (left)
AC power adaptor (supplied)
To an AC
outlet
2
The CHARGE indicator on the speaker
Disposing of the
system will light up to indicate that the
battery is being charged. speaker system
Be sure to remove the built-in rechargeable
batteries from the speaker system before you
dispose of the speaker system.
1
Remove 13 screws from the speaker
system using a cross-point screw driver
as illustrated below.
CHARGE indicator
Notes
• It takes about 28 hours to fully charge an empty battery.
• Charge the rechargeable battery within a temperature of
0 ˚C to 35 ˚C (32 ˚F to 95 ˚F).
• If you turn on the speaker system while charging the
battery, battery charging stops and the CHARGE
indicator turns off. You can use the speaker system by
the power from the AC adaptor.
• The duration time of the rechargeable battery is about 4
hours. If the light of the reflector becomes weak, it
means the rechargeable battery is low. So, turn off the
2
speaker system and charge the battery. Open the cabinet of the speaker system
• Even after battery charging is finished, the CHARGE
and remove the one screw to remove the
indicator always lights up.
rechargeable battery as illustrated.
• The life of the built-in rechargeable battery is about 3
years. But it differs depending on operating conditions.
• Use only the supplied AC power adaptor. Do not use Battery
any other AC power adaptor.
N Operating the system
Listening to a program
Before using the speaker system, charge the built-
in rechargeable battery first.
Turn down the volume of the speaker system
before playing back a program on the connected N Additional information
audio/video equipment.
OFF y ON Precautions
The switch of the
reflector light
• When the transmitter is not to be used for a long
period of time, disconnect the AC power
High
adaptor from the AC outlet holding the plug. Do
TUNING
not pull on the cord.
button
VOLUME control
POWER switch Notes on the location you set the speaker
POWER indicator Low system
• Do not leave the wireless speaker system in a
1
location subject to:
First turn on the audio/video equipment
– Direct sunlight or extremely high temperature such
and start playing.
as near a heater or in a car with its windows closed.
The power indicator of the transmitter
– High humidity such as in a bathroom.
will light up. – Excessive dust or sandy places.
– The speaker system is magnetically shielded, but do
2
not put a recorded tape, watch, cash card or floppy
Turn on the speaker system.
disk in front of the speaker system.
The power indicator of the speaker • Set up the speaker system on a flat surface.
system will light in red. • Depending on where you set the speaker
system, it may fall down. Do not leave valuables
3
Select the radio frequency with the near the speaker system.
CHANNEL selector.
Notes on charging the battery
• When you charge the rechargeable battery, use
the supplied AC adaptor only.
• The charging time differs depending on usage
conditions of the battery.
1 2 3
CHANNEL
• When you use the battery for the first time or the
battery is not to be used for a long time, the
battery duration time may become shorter than
Note
the usual duration time. However, after you
If you use the unit near a cordless telephone, it may
charge the battery several times, the battery
cause radio interference. If poor reception occurs, try
another channel using the CHANNEL selector.
duration time returns to its normal condition.
• If the battery duration time becomes half of its
4
Turn up the volume to a moderate level
normal time even after the battery is charged
with the VOL control.
fully, the battery is worn out. In this case,
Press the TUNING button briefly for
consult your nearest Sony dealer.
automatic tuning of the speaker system.
Notes on using the speaker system
If you do not receive a clear audio signal,
• Do not disassemble the speaker unit, built-in
press it again.
amplifier or cabinet.
• Do not insert an object into the jack. Doing so
Sending RF signals from the Transmitter
may cause a malfunction.
The transmitter starts sending the RF signals
• Keep the volume at a moderate level to prevent
automatically, when it detects audio signals from
distortion.
the equipment connected.
• Do not carry the speaker unit by its reflector. If
If it does not detect an audio signal for more than
you do so, the speaker system may detach from
approximately four minutes, the transmitter will
stop sending RF signals, and the power indicator the reflector.
turns off.
Note on cleaning
When the transmitter receives an audio signal
again, it starts sending the RF signals, and the Clean the cabinet of the speaker system with a soft
power indicator will light in red again. cloth slightly moistened with water or a mild
If the audio signal is very weak, the transmitter detergent solution. Do not use any type of abrasive
does not send RF signals. If the transmitter is pad, scouring powder or solvent such as alcohol or
connected to a headphone jack, make sure the benzene as it may mar the finish of the cabinet.
volume of the equipment connected is set to 5 – 6
When the color of your monitor screen
or higher.
becomes irregular
You may not hear the beginning of the sound from
Because this speaker system is magnetically
the speaker system until the transmitter starts
shielded, you can set it up near a monitor. But
sending the RF signals after detecting an audio
depending on the model of the monitor, color
signal.
irregularity may occur.
Note
To correct the color irregular
If the transmitter is connected to the headphones jack of
the source equipment, set the volume of that equipment as Turn off the monitor, and then turn it on again
high as possible without distorting the audio signal. after 15 to 30 minutes.
Using the Built-in Rechargeable Batteries
If color irregularity remains after
The built-in rechargeable batteries allow you to use
performing the above
the unit anywhere.
• Separate the monitor and the speaker system.
Remove the supplied AC power adaptor from the
• Make sure that no magnetic object, such as may
DC IN jack of the unit to use the built-in
be attached to a door of shelf, healthcare device
rechargeable batteries.
or toys, etc., is located near the speaker system.
To use the illumination of the reflector
If you have any questions or problems concerning
Turn on the switch of the reflector light.
the system that are not covered in this manual,
Notes please consult your nearest Sony dealer.
• If a hissing noise is heard, move it closer to the
transmitter. Be sure to bring the speaker system and the
• If you turn up the volume of the speaker system too transmitter to the Sony dealer when requiring
high, the light of the reflector may flicker. But this is not
repair work.
a malfunction.
• If you hold the antenna of the transmitter with your
hand, noise may occur. But this is not a malfunction.
Français
Troubleshooting
AVERTISSEMENT
No sound/Muffled sound
Pour éviter tout risque d'incendie ou
, Check the connection of the audio/video
d'électrocution, ne pas exposer cet appareil à la
equipment.
pluie ou à l'humidité.
, Check that the audio/video equipment is turned
Pour prévenir tout risque d'électrocution,
on.
n'ouvrez jamais le coffret. Adressez-vous à un
, Turn up the volume on the connected audio/
personnel qualifié uniquement pour toute
video equipment, if the transmitter is connected
intervention sur l'appareil.
to the headphones jack.
, Change the radio frequency with the CHANNEL
Avertissement
selector on the transmitter, then press the
Soyez avisé que toute modification non
TUNING button again.
expressément approuvée dans le présent mode
, The speaker system's POWER indicator light is
d'emploi pourrait entraîner l'annulation de vos
weak or turned off. droits d'utilisation de ce produit.
• Charge the built-in rechargeable battery or if the
Pour les utilisateurs au Canada
POWER indicator is still off after charging the
built-in rechargeable battery, take the speaker
Son utilisation est autorisée seulement aux
system to a Sony dealer for replacement of the
conditions suivantes: (1) il ne doit pas produire de
rechargeable battery.
brouillage et (2) l'utilisateur du dispositif doit être
, If you connect the transmitter to the LINE OUT or
prêt à accepter tout brouillage radioeléctrique reçu,
REC OUT jack of an audio reproducer, make sure
même si ce brouillage est susceptible de
that the NOISE FILTER switch is set to OFF.
compromettre le fonctionnement du dispositif.
, Make sure that the NOISE FILTER switch is set to
either ON or OFF (If the switch gets stuck
Pour les utilisateurs aux Etats-Unis et au Canada
between ON and OFF, the sound will be cut off).
RECYCLAGE DES ACCUMULATEURS À
Distortion HYDRURE MÉTALLIQUE DE NICKEL
, If the transmitter is connected to the headphones
Les accumulateurs à hydrure
jack, turn down the volume of the connected
métallique de nickel sont
audio/video equipment. If the connected audio/
video equipment has bass boost function, set its recyclables.
function to OFF. Vous pouvez contribuer à
, If the connected audio/video equipment has a préserver l'environnement en
LINE OUT jack, connect its LINE OUT jack. rapportant les piles usées dans
, Change the radio frequency with the CHANNEL un point de collection et
selector on the transmitter. recyclage le plus proche.
, The speaker system's POWER indicator light is
weak or turned off.
Pour plus d'informations sur le recyclage des
• Charge the built-in rechargeable battery or if the
accumulateurs, téléphonez le numéro gratuit
POWER indicator is still off after charging the
1-800-822-8837 (Etats-Unis et Canada
built-in rechargeable battery, take the speaker
uniquement), ou visitez
system to a Sony dealer for replacement of the
http://www.rbrc.org/
rechargeable battery.
, If you connect the transmitter to LINE OUT or
Avertissment : Ne pas utilliser des
REC OUT jack of an audio reproducer, make sure
accumulateurs à hydrure métallique de nickel
that the NOISE FILTER switch is set to OFF.
qui sont endommagées ou qui fuient.
Loud background noise
, Move closer to the transmitter. As you move
away from the transmitter, more noise is likely to
Bienvenue !
be heard.
, If the transmitter is connected to the headphones
Nous vous remercions d'avoir fait l'acquisition du
jack, turn up the volume of the connected audio/
système d'enceinte stéréo sans fil SRS-RF90RK/
video equipment.
RF90R de Sony. Avant de faire fonctionner cet
, Change the radio frequency with the CHANNEL
appareil, lisez attentivement le présent mode
selector on the transmitter, then press the
TUNING button again.
d'emploi et conservez-le pour toute référence
, The speaker system's POWER indicator light is
ultérieure.
weak or turned off.
Cet appareil offre, entre autres, les caractéristiques
• Charge the built-in rechargeable battery or if the
suivantes :
POWER indicator is still off after charging the
• Système sans fil vous permettant l'utilisation
built-in rechargeable battery, take the speaker
sans fils d'enceinte encombrants.
system to a Sony dealer for replacement of the
• Longue portée de transmission des signaux allant
rechargeable battery.
, If you connect the transmitter to the LINE OUT or jusqu'à environ 46 m (150 pi).
REC OUT jack of an audio reproducer, make sure • Trois options de canaux de transmission
that the NOISE FILTER switch is set to OFF.
permettant une réception optimale des signaux.
• Fonction de syntonisation automatique à
The battery duration time is short
l'enceinte.
, If you use the battery under the temperature
• Réflecteur fixé au système d'enceinte offrant une
lower than 0 ˚C (32 ˚F), this is not a malfunction.
reproduction sonore haute fidélité.
, The battery life may end. If the battery duration
• Construction stéréo à boîtier unique offrant un
time becomes half of its normal time even after
large champ sonore.
the battery is charged fully, consult your nearest
Sony dealer • Deux possibilités d'alimentation : avec
l'adaptateur CA fourni ou la batterie
rechargeable intégrée.
Specifications
• Conception novatrice et originale avec éclairage
bleu, un design élégant qui convient bien au
General
décor de n'importe quelle pièce.
Carrier frequency 913.5 – 914.5 MHz
Channel Ch1, Ch2, Ch3
Modulation FM stereo
Remarques sur la
Transmitter (SRS-RF90RK only)
qualité de
Power source DC 9 V: supplied AC power adaptor
(AC-S901)
transmission
Audio input phono jacks/stereo mini jack
Input impedance 33 k /51 switchable
Comme le système de cet appareil utilise des
Dimensions Approx. 136 100 136 mm
signaux de très haute fréquence dans la bande des
(6 4 1 / 6 in.) (w/h/d)
3
900 MHz, l'environnement de l'appareil peut
Mass Approx. 146 g (5.2 oz.)
entraîner une détérioration de la qualité de
Speaker system SRS-RF90RK, SRS-RF90R
transmission. Les exemples suivants illustrent les
Speaker system 2 way magnetically shielded
situations pouvant réduire la plage de
Enclosure type Bass reflex
transmission et perturber la réception.
Speaker units tweeter: 30 mm 2
• Utilisation à l'intérieur d'un bâtiment à structure
woofer: 57 mm 1
en acier.
Power source DC 9 V: supplied AC adaptor (AC-S906T)
• Utilisation dans des pièces contenant de
Rated output Built in amplifiers total 4W (while
nombreux classeurs ou autres éléments en acier.
using the supplied AC adaptor)
• Utilisation à proximité d'un grand nombre
* power output:
d'appareils électriques générant des parasites
Tweeter: 0.25W + 0.25W < 10%
électromagnétiques.
T.H.D., 5 kHz 24 ohms
• Installation du transmetteur sur un instrument
Woofer: 3.5W < 10% T.H.D., 1kHz
métallique.
6 ohms
Dimensions Approx. 234 300 126 mm • Utilisation à proximité d'une route.
( 9 1 / 11 7 / 5 in.) (w/h/d) • Parasites ou interférences autour de l'appareil,
4 8
Mass Approx. 905 g (31.9 oz.) incl. provenant d'émetteurs-récepteurs de camions
built-in rechargeable battery ou d'autres appareils.
• Parasites ou interférences autour de l'appareil,
Built-in Ni-MH rechargeable battery
provenant de systèmes de communication sans
Voltage 7.2 V
fil installés le long des routes.
Capacity 700 mAh
• Installation du transmetteur directement sur le
Duration time Approx. 4 hours
sol. Il est recommandé d'installer le
(with the 10 mW reflector light OFF)
transmetteur en hauteur, par exemple sur un
bureau.
Charging time Approx. 28 hours (from fully
discharged to fully charged)
Supplied accessory
The transmitter (SRS-RF90RK only)
AC adaptor (2 for SRS-RF90RK) (1 for SRS-RF90R)
Connecting cord phono plug-stereo miniplug (1m) (1)
(SRS-RF90RK only)
Operating instructions (1)
Optional accessory
Plug adaptor PC-236MS (stereo mini jack y
monaural mini plug)
Design and specifications are subject to change without notice.
C Raccordement à un téléviseur ou à un
N Préparatifs
autre appareil.
Si des parasites sont audibles lorsque le
Déballage
transmetteur est relié à la prise de casque
de votre téléviseur ou magnétoscope,
Vérifiez que vous disposez de tous les éléments
réglez le commutateur NOISE FILTER à
suivants :
ON.
• Système d'enceinte
• Transmetteur (SRS-RF90RK uniquement)
Vers les prises
Transmetteur
• Adaptateur CA AUDIO IN A
(deux pour le SRS-RF90RK) ou (un pour le
SRS-RF90R)
• Câble de liaison (prises phono y mini-fiche
B R A L DC IN 9V 1 2 3
stéréo), 1 m (SRS-RF90RK uniquement) OFF ON AUDIO IN
NOISE FILTER CHANNEL
Canal droit
Raccordement du Canal gauche
(rouge) (blanc)
système
Raccordement du réflecteur fourni au
système d'enceinte Câble de liaison
(fourni)
Insérez les fiches solidement et jusqu'au fond, tel
qu'illustré.
Vers la mini-prise
stéréo
Téléviseur ou
autre appareil
Remarques
• Si vous raccordez le transmetteur à une prise LINE
OUT ou REC OUT, ne réglez pas le commutateur
NOISE FILTER à ON, sinon le volume sera limité.
Raccordement du transmetteur à un
• Le commutateur NOISE FILTER n'agit sur le son
appareil audio ou vidéo que dans les cas ou le raccordement du schéma C
est utilisé. Dans les cas où le raccordement A ou B
est utilisé, il n'a aucun effet.
Pour les propriétaires du SRS-RF90R
Vous pouvez utiliser le transmetteur fourni soit • Placé près d'un téléviseur, le transmetteur risque de
subir des interférences. Le cas échéant, éloignez-le
avec le MDR-RF915RK, soit avec le MDR-
du téléviseur.
RF945RK. Si vous avez déjà installé le
transmetteur, il n'est pas nécessaire d'effectuer le
Raccordement du transmetteur à une
raccordement suivant. Cependant, vous ne pouvez
prise de courant à l'aide de
pas utiliser un transmetteur fourni avec un
l'adaptateur CA fourni.
système de casque d'écoute sans fil d'un modèle
autre que ceux cités ci-dessus.
Pour les propriétaires du SRS-RF90RK Transmetteur
Installez le transmetteur en effectuant les étapes
suivantes. Choisissez le raccordement à effectuer
Vers la
selon le type de prise de l'appareil audio ou vidéo
prise
DC IN 9 V
auquel vous souhaitez raccorder le transmetteur. Vers une prise
CA
A Raccordement à une prise LINE OUT ou Adaptateur CA
(fourni : AC-S901 )
REC OUT
Remarques
• Utilisez uniquement l'adaptateur CA fourni. N'utilisez
aucun autre adaptateur CA.
Transmetteur
Polarité de la fiche
B R A L DC IN 9V
OFF ON 1 2 3
NOISE FILTER AUDIO IN CHANNEL
• Lorsque vous raccordez directement le câble de liaison à
Vers la prise
une prise de casque, le signal audio n'est pas émis par le
AUDIO IN B
canal droit. Dans ce cas, utilisez l'adaptateur de fiche
PC-236MS vendu séparément.
• Si l'appareil raccordé est équipé de la fonction AVLS
(système de limitation automatique du volume),
désactivez cette fonction lorsque vous utilisez le
Câble de liaison
transmetteur. Sinon, vous devrez augmenter le volume
(fourni)
du système d'enceinte, ce qui pourrait engendrer des
parasites.
• Si l'appareil raccordé est équipé de la fonction BASS
BOOST ou MEGA BASS (amplification des graves,
désactivez cette fonction lorsque vous utilisez le
Canal gauche Canal droit
transmetteur. Sinon, le son provenant du système
(blanc) (rouge)
d'enceinte risque d'être déformé.
• N'installez pas le transmetteur près d'une lampe
Vers les prises LINE
fluorescente, etc. lorsque vous utilisez le système.
OUT ou REC OUT
* «WALKMAN» est une marque déposée par Sony
Corporation pour représenter les produits stéréo dotés
d'écouteurs.
Chaîne stéréo,
magnétoscope, etc.
Portée du transmetteur
B Raccordement à une prise de casque La portée optimale du transmetteur est de 46 m
(150 pi) environ sans que le système ne capte
Transmetteur d'interférences. Cependant, cette distance peut
varier selon l'environnement de l'appareil. Si le
Vers les prises
système capte des parasites alors qu'il est utilisé
AUDIO IN A
dans la zone définie ci-dessus, rapprochez le
transmetteur et le système d'enceinte ou
sélectionnez un autre canal.
B R A L DC IN 9V
OFF ON 1 2 3
NOISE FILTER AUDIO IN CHANNEL
Remarques
• Quand vous utilisez le système d'enceinte dans la zone
de couverture du transmetteur, la direction du
Canal droit Canal gauche
transmetteur par rapport à l'auditeur n'importe pas.
(rouge) (blanc)
• Dans la zone de réception des signaux, il existe
cependant certains endroits (zones de silence) où la
réception des signaux RF est impossible. Il s'agit d'une
caractéristique inhérente aux signaux RF et n'indique
Câble de liaison pas un problème de fonctionnement. Il est possible de
(fourni)
modifier l'emplacement de la zone de silence en
déplaçant légèrement le transmetteur.
Recharge de la batterie
du système d'enceinte
Vers la prise de
Adaptateur de
Première utilisation du système
casque ou LINE OUT
fiche universel
(mini-prise stéréo)
(non fourni) d'enceinte
Discman, MD, Lorsque vous utilisez le système pour la première
Vers la prise de
WALKMAN*, fois, chargez la batterie tel qu'indiqué ci-dessous.
casque (prise
magnétoscope, etc.
1
stéréo)
Raccordez le système d'enceinte à une
source d'alimentation.
Haut-parleur Haut-parleur des
aiguës (gauche)
des aiguës
(droit)
Adaptateur CA (fourni)
Vers une prise CA
Voir page suivante