Be Sure To Read The Following Safeguards When Setting Up Your Projector - Sharp XV-Z10000 Operation Manual

IMPORTANT SAFEGUARDS
Be sure to read the following safeguards when setting up
your projector.
Caution concerning the lamp unit
I Potential hazard of glass particles if
lamp ruptures. In case of lamp rupture,
contact your nearest Sharp Authorised
Projector Dealer or Service Centre for
replacement.
See "Replacing the Lamp" on pages 76-78.
Cautions concerning the setup of the projector
I For minimal servicing and to maintain high image qual-
ity, SHARP recommends that this projector be installed
in an area free from humidity, dust and cigarette smoke.
When the projector is subjected to these environments,
the lens must be cleaned more often. As long as the
projector is regularly cleaned, use in these environ-
ments will not reduce the overall operation life of the
unit. Internal cleaning should only be performed by an
Sharp Authorised Projector Dealer or Service Centre.
Do not set up the projector in places exposed to
direct sunlight or bright light.
I Position the screen so that it is not in direct sunlight or
room light. Light falling directly on the screen washes
out the colours, making viewing difficult. Close the cur-
tains and dim the lights when setting up the screen in a
sunny or bright room.
The projector may safely be tilted to a maximum
angle of 5 degrees.
I Placement should be within ±5 degrees.
Do not subject the projector to hard impact and/
or vibration.
I Take care with the lens so as not to hit or damage the
surface of the lens.
Rest your eyes occasionally.
I Watching the screen for long hours continuously will
make your eyes tired. Be sure to occasionally rest your
eyes.
Avoid locations with high or low temperature.
I The operating temperature for the projector is from +5°C
to +35°C.
I The storage temperature for the projector is from
–20°C to +60°C.
Do not block the intake and exhaust vents.
I Allow at least 30 cm of space between the exhaust vent
and the nearest wall or obstruction.
-8
I Be sure that the intake vent and the exhaust vent are
not obstructed.
I If the cooling fan becomes obstructed, a protection cir-
cuit will automatically turn off the projector. This does
not indicate a malfunction. Remove the projector power
CAUTION
cord from the wall outlet and wait at least 10 minutes.
PRECAUCIÓN
PRÉCAUTION
Place the projector where the intake and exhaust vents
are not blocked, plug the power cord back in and turn
BQC-XVZ100001
on the projector. This will return the projector to the
normal operating condition.
Cautions regarding the transportation of the pro-
jector
I When transporting the projector, be sure not to subject
it to hard impact and/or vibration, as this can result in
damage. Take extra caution with the lens. Before mov-
ing the projector, be sure to unplug the power cord from
the wall outlet, and disconnect any other cables con-
nected to it.
Other connected equipment
I When connecting other audio-visual equipment or a
computer to the projector, make the connections AF-
TER turning off the projector and the equipment to be
connected.
I Please read the operation manuals of the projector and
the equipment to be connected for instructions on how
to make the connections.
Temperature monitor function
I If the projector starts to overheat
due to setup problems or blockage
of the air vents, "
"
corner of the picture. If the tem-
perature continues to rise, the lamp will turn off, the
temperature warning indicator on the projector will blink,
and after a 90-second cooling-off period the power will
shut off. Refer to "Maintenance Indicators" on page 74
for details.
Info
The cooling fan regulates the internal temperature, and
its performance is automatically controlled. The sound
of the fan may change during projector operation due
to changes in the fan speed. This does not indicate
malfunction.
Do not unplug the power cord during projection or cool-
ing fan operation. This can create damage due to the
rise in internal temperature, as the cooling fan also
stops.
" and
" will blink in the lower left