Sharp XV-Z10000 Service Manual
Hide thumbs Also See for XV-Z10000:
Table of Contents

Advertisement

Available languages

Available languages

Quick Links

In the interests of user-safety (Required by safety regulations in some countries) the set should be restored
to its original condition and only parts identical to those specified should be used.
Im lnteresse der Benutzersicherheit (erforderliche Sicherheitsregeln in einigen Ländern) muß das Gerät in seinen
Originalzustand gebracht werden. Außerdem dürfen für die spezifizierten Bauteile nur identische Teile verwendet
werden.
SHARP CORPORATION
SERVICE MANUAL
SERVICE-ANLEITUNG
PROJECTOR
PROJEKTOR
MODEL
MODELL
This document has been published to be used for
after sales service only.
The contents are subject to change without notice.
1
S23X3XVZ10000
XV-Z10000
XV-Z10000

Advertisement

Table of Contents
loading

Summary of Contents for Sharp XV-Z10000

  • Page 1 XV-Z10000 SERVICE MANUAL SERVICE-ANLEITUNG S23X3XVZ10000 PROJECTOR PROJEKTOR MODEL XV-Z10000 MODELL In the interests of user-safety (Required by safety regulations in some countries) the set should be restored to its original condition and only parts identical to those specified should be used.
  • Page 2: Table Of Contents

    XV-Z10000 CONTENTS Page Page • SPECIFICATIONS ..........3 • SCHEMATIC DIAGRAM ........ 100 • INPOTANT SERVICE SAFETY NOTES .... 4 • PRINTED WIRING BOARD ASSEMBLIES ... 147 • OPERATION MANUAL ........8 • PARTS LIST Ë ELECTRICAL PARTS ....... 155 •...
  • Page 3: Specifications

    A442WJZZ (this manual)) / for Chinese, Korean and Arabic (TINS-A443WJZZ), SharpVision Manager operation manual (TINS-A452WJZZ) This SHARP projector uses a DMD Chip. This very sophis- This unit has some inactive pixels within acceptable toler- ticated panel contains 921,600 pixels. As with any high tech- ances which may result in inactive dots on the picture screen.
  • Page 4: Inpotant Service Safety Notes

    XV-Z10000 IMPORTANT SERVICE SAFETY NOTES (for USA) Ë Service work should be performed only by qualified service technicians who are thoroughly familiar with all safety checks and servicing guidelines as follows: » Use an AC voltmeter with sensitivity of 5000 ohm per WARNING volt., or higher, sensitivity to measure the AC voltage...
  • Page 5: Note To Service Personnel

    XV-Z10000 NOTE TO SERVICE NOTE POUR LE PERSONNEL PERSONNEL D’ENTRETIEN PRECAUTION POUR LES RADIATIONS UV UV-RADIATION PRECAUTION La source de lumière, la lampe , dans le projecteur The light source, lamp, in the projector emits small émet de petites quantités de radiation UV.
  • Page 6: Lamp Replacement

    XV-Z10000 UV-RADIATION PRECAUTION (Continued) PRECAUTION POUR LES RADIATIONS UV (Suite) Lamp Replacement Remplacement de la lampe Note: Remarque: Since the lamp reaches a very high temperature Comme la lampe devient très chaude pendant le during units operation replacement of the lamp fonctionnement de l’unité, son remplacement ne doit...
  • Page 7: Power Unit

    XV-Z10000 WARNING: High brightness light source, do not stare into the beam of light, or view directly. Be especially careful that children do not stare directly in to the beam of light. WARNING: TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS UNIT TO MOISTURE OR WET LOCATIONS.
  • Page 8: Operation Manual

    XV-Z10000 Location of Controls Adjustment buttons MENU button (", ', \, |) For displaying adjustment For selecting menu items. and setting screens. ENTER button RESIZE button For setting items selected For switching the screen or adjusted on the menu. size (SIDE BAR, SMART STRETCH, etc.).
  • Page 9 XV-Z10000 INPUT 3 terminal Terminal for connecting video Pr o j e c t o r (Re a r V i e w ) equipment with an S-video terminal. INPUT 1 terminals RS-232C terminal Terminals for For controlling component and projector using a RGB signals .
  • Page 10 XV-Z10000 Re m o t e Co n t r o l (Fr o n t V i e w ) Power (ON/OFF) buttons For turning the power on or off. KEYSTONE button For adjusting Keystone Correction or Vertical Size setting.
  • Page 11: Using The Remote Control

    XV-Z10000 Using the Remote Control A v a i l a b l e Ra n g e o f t h e Re m o t e Co n t r o l The remote control can be used to control the projector Remote control within the ranges shown in the illustration.
  • Page 12: Connection Pin Assignments

    XV-Z10000 Connection Pin Assignments Connecting Pin Assignments DVI-I (INPUT 5 / DIGITAL INPUT) port : 29 pin connector • DVI Digital INPUT Pin No. Signal Pin No. Signal T.M.D.S data 2– Hot plug detection T.M.D.S data 2+ T.M.D.S data 0–...
  • Page 13 XV-Z10000 Dimensions Rear View Side View Top View Side View Front View Bottom View Unit: inches (mm)
  • Page 14: Removing Of Major Parts

    XV-Z10000 REMOVING OF MAJOR PARTS 1. Removing the top panels 1-1. Remove the six lock screw. 2-1. Remove the two screws and detach the LED PWB. 1-2. Press on side Arrow A of the bottom body 2-2. Remove the one screw and detach the R/C PWB.
  • Page 15 XV-Z10000 2. Removing the cooling fan and PWB unit assembly. 3-1. Disconnect the ten connectors. 3-2. Remove the two screws and detach the lamp socket. 3-3. Remove the two screws and detach the cooling fan. 3-4. Remove the four screws and detach the PWB unit assembly.
  • Page 16 XV-Z10000 3. Removing the rear panel, PC unit, cooling duct and main PWB unit. 4-1. Remove the two screws. 4-2. Remove the three screws and detach the rear panel. 5-1. Remove the two screws. 5-2. Remove the four hexagonal supports and detach the shield plate.
  • Page 17 XV-Z10000 4. Removing the power unit shield , power/ballast unit and power unit. Remove the seven screws and detach the power unit shield. 10-1. Remove the two screws. 10-2. Remove the four white supports and detach the power unit. Remove the four screws and detach the power unit.
  • Page 18 XV-Z10000 5. Removing the optical mechanism unit and R/C PWB unit. Remove the six screws and detach the optical mechanism unit. Remove the one screw and detach the R/C PWB unit. Optical mechanism unit R/C PWB unit...
  • Page 19 XV-Z10000 6. Removing the lamp unit, CW fan, outlet fan, bimetal, wind way duct, shield plate and formater PWB. Remove the three screws and detach the lamp unit. Remove the two screws and detach the CW fan. Remove the three screws and detach the outlet fan.
  • Page 20: Resetting The Total Lamp Timer

    The lamp does not • Lamp circuit failure. • Take the projector to your nearest MENT indicator light up. Authorized Sharp Vision Service Center or The lamp requires • Lamp has been used for Dealer for repair. replacement. over 1,900 hours.
  • Page 21: The Optical Unit Outline

    XV-Z10000 THE OPTICAL UNIT OUTLINE Layout for proper setup of the optical components and parts (top view) Projection lens Prism DMD Chips Condensor lens IR-cut mirror Light tunnel Relay lens Fold mirror Condensor lens Color filter Lamp Item Descriptions 1 Lamp The DC Light source lamp with parabola reflector.
  • Page 22 XV-Z10000 Adjusting the mirrors Make adjustment by the indication territory on the screen to prevent the circumference of the screen from getting dark because a lighting range deviated. 1. Remove the top body so that the optical unit may be seen. Display white only screen on the screen.
  • Page 23 XV-Z10000 When the DMD unit has been replaced Note: DMD chip and Formatter PWB are supplied at the same time, and an exchange only with DMD isn't done.Refer to "REMOVING OF MAJOR PARTS" when exchanging Formatter PWB. There is no need to readjust the back focal distance of the projection lens. If focusing is noticeably poor, however, make this readjustment.
  • Page 24: Electrical Adjustment

    XV-Z10000 ELECTRICAL ADJUSTMENT Adjusting point Adjusting conditions Adjusting procedure Hook up a signal generator, or a DOSV or Mac personal computer to the projector in order to feed the signals specified in the Adjusting conditions. Adjusting point Adjusting conditions Adjusting procedure EEPROM 1.
  • Page 25 XV-Z10000 Adjusting point Adjusting conditions Adjusting procedure Video bright- By selecting AUTO with the control SW or the button 1. Select the following group ness/contrast on the remote control after inputting the signal, it is and subject. adjustment automatically adjusted.
  • Page 26 XV-Z10000 Adjusting point Adjusting point Adjusting conditions Adjusting conditions Adjusting procedure Adjusting procedure 1. Select OFF from the process mode LINE. Off-timer per- Make sure the off-timer starts with 5 minutes onscreen formance and the set turns itself off in 5 minutes.
  • Page 27 XV-Z10000 Adjusting the PC Board Adjusting point Adjusting conditions Adjusting procedure 1. Initializing the EEPROM 1) Press SW2002 to enter the process mode. 2) Execute the S1 command on the SSS menu. (The S1 command initializes the PC board alone. Do not execute the S2 command because otherwise the adjustment data other than the PC board will be initialized.)
  • Page 28 XV-Z10000 Background adjustment method Adjusting point Adjusting conditions Adjusting procedure Adjust it in the following 2 steps. 1. Adjustment item process adjustment DLP GAMMA 2. Input signal: component video 75% white signal 0.7 ± 0.05 Vp-p (synchronized part excluded.) 3. DLP GAMMA initial value 6 4.
  • Page 29 XV-Z10000 Process menu 1 Adjusting point Adjusting conditions Adjusting procedure Group Sub Group Subject Adjust PC Image A/D (RGB) R-BRIGHT G-BRIGHT B-BRIGHT AD-AUTO A/D (COMP) G-BRIGHT CB-OFFSET CR-OFFSET A/D AUTO Adjust HDDE formatter CW-INDEX DLP-GAMMA R-BRIGHT G-BRIGHT B-BRIGHT R-GAIN G-GAIN...
  • Page 30 XV-Z10000 Process menu 2 Adjusting point Adjusting conditions Adjusting procedure Group Sub Group Subject INITIAL SETTING TIME LAMP Sample Pattern PATTERN RGB(50) CROSS STEP COLOR Adjust CVIC CVIC MODE -PROGRESSIVE MD SW PTGSW C-TESTSW C-ILG-LY C-MOD-LY C-VE-LY CVIC ENH-PLUS -ENHANCE-VIDEO...
  • Page 31 XV-Z10000 Process menu 3 Adjusting point Adjusting conditions Adjusting procedure Group Sub Group Subject Adjust CVIC CVIC TBL-NO -PTG TESTSW ENABLE MV-F VDDYP CVIC CMS-HUE-R -CMS-HUE CMS-HUE-Y CMS-HUE-G CMS-HUE-C CMS-HUE-B CMS-HUE-M CVIC CMS-SAT-R -CMS-SAT CMS-SAT-Y CMS-SAT-G CMS-SAT-C CMS-SAT-B CMS-SAT-M CVIC...
  • Page 32: Trouble Shooting Table

    XV-Z10000 TROUBLE SHOOTING TABLE Checking the basic performance Is the POWER LED on or flickering in red or blue? Go to "Checking the power unit" Is the set turned on by the set's or remote controller's power key? Go to "Checking the microcomputer peripherals"...
  • Page 33 XV-Z10000 Checking the power unit Are all the connectors inside the power unit tightly connected? Insert the connectors CN7105, 7103, 7101AND 7102 tightly. Is the lamp cover closed completely? Tighten up the lamp door closed with the screws. Is the bimetal switch off?
  • Page 34 XV-Z10000 Checking the PC PWB Is the user menu properly displayed? Check the on-screen display. Check the basic signal flow. The signal flow from CVIC_IC to the panel output is the same for the component and video signals. Therefore the lines after CVIC are not checked.
  • Page 35 XV-Z10000 Checking the RGB input Feed the sync-separated DTV RGB signal to INPUT1 or INPUT2. (The 480i and 580i component signals are not included.) Using the front-panel key or the remote control, select INPUT1 or INPUT2. Does the image appear? Check to see if the video input is as specified.
  • Page 36 XV-Z10000 Checking the video input Make sure the input signal setting is as specified. Is there the video signal at the land of C8077? Input PWB defective. Check the sync signal. IC8025 or IC8004 defective. Checking the input signal setting...
  • Page 37 XV-Z10000 Checking the sync signal Is there vertical sync signal at TL8134? Is there horizontal sync signal at TL8133? Check the input signal setting. Input PWB defective. Is there vertical sync signal at TL8131? Is there horizontal sync signal at TL8130?
  • Page 38 XV-Z10000 Checking the RGB signal Is the type of signal set at RGB? Set to the RGB signal. Call the process mode. Select R, G and B separately on the pattern menu. Go to “Checking the GA4 peripheral circuits”. Set the signal generator to...
  • Page 39 XV-Z10000 Checking the GA4 peripheral circuits Call the process mode, and select R, G and B separately on the pattern menu. Are there specified R, G and B video output signals? End of checking the GA4 peripheral circuits. Are the measured signals...
  • Page 40 XV-Z10000 Checking the component inputs (Except for 480i) Feed the component signal to INPUT1 or INPUT2. Using the front panel key or the remote control, select INPUT1 or INPUT2. Does an image appear on the screen? Go to "Checking the SOG circuit".
  • Page 41 XV-Z10000 Checking the SOG circuit Measure the signal at TL8136 on the oscilloscope. Is the composite sync signal played back timely? There is no problem with the SOG circuit. End. Measure the land of C8069 on the oscilloscope. Is there the Y signal including the sync signal? Go to “Checking the input...
  • Page 42 XV-Z10000 Checking the video input Feed the composite video signal to INPUT4. Using the front panel key or the remote control, select INPUT4. Select VIDEO as the type of signal on the user menu. Does the image appear? Go to "Checking the video sync signal".
  • Page 43 XV-Z10000 Measure the VPC (IC8338) clock signal at TL8004. Is the clock signal as specified? IC8338 defective. Go to “Checking the video sync signal”. IC8025 or its peripheral circuit defective. Checking the video sync signal Using the oscilloscope, measure the signal at TL8140.
  • Page 44 XV-Z10000 Checking the DSUB input. Feed the PC-RGB signal to INPUT5. Select INPUT5 as the input. Check to see if there are the R, G and B signals at pins (126), (136) Does the image appear? and (146) of IC8004.
  • Page 45 XV-Z10000 Checking the lamp light-up The lamp fails to light up. Is discharge sound heard when turning on the power switch? Is the lamp or CW line socket out of position? Reconnect the sockets tightly. Replace the lamp or the...
  • Page 46 XV-Z10000 No horizontal synchronization Is the terminal input connection as specified? Is the cable tightly connected? Use the specified cable. Reconnect it tight enough. Is there the horizontal sync pulse at pin (14) of IC2506? Check the line between IC2506 and the input terminal.
  • Page 47 XV-Z10000 Checking IC3504 (3D Noise Reduction) and its Peripheral Circuits Are there the input signals at pins (88) (Y signal) and (96) (C signal) of IC3504? Check the signal input circuit or IC2505 and its peripheral circuits. Are there the output...
  • Page 48 XV-Z10000 Checking the Component and RGB Inputs Are there signals at pins (34), (36) and (38) of IC2505? Check the signal input circuit or IC2505 and its peripheral circuits. There are no RGB colors. Check the circuit of the color that fails to appear.
  • Page 49: Technische Daten

    ROM (UDSKAA028WJN1), Bedienungsanleitungen; für 7 europäische Sprachen (TINS-A442WJZZ (diese Anleitung)) / für Chinesisch, Koreanisch und Arabisch (TINS-A443WJZZ), SharpVision Manager-Bedienungsanleitung (TINS- A452WJZZ) Dieser SHARP-Projektor verwendet einen DMD-Chip. Dieses hoch Dieses Gerät hat einige inaktive, innerhalb akzeptierter Toleranzgrenzen entwickelte Panel enthält 921.600 Pixel. Bei allen technologisch liegende Bildpunkte, die als leuchtende oder als nicht aktive Punkte auf fortschrittlichen, elektronischen Geräten, z.
  • Page 50: Hinweise Für Das Wartungspersonal

    XV-Z10000 HINWEIS FÜR DAS WARTUNGSPERSONAL Auswechseln der Lampe ACHTUNG: UV-STRAHLUNG Hinweis: Da die Lampe während des Betriebs sehr heiß wird, Die Beleuchtungsquelle des LCD-Projektors, eine sollte die Lampe erst ausgewechselt werden, nachdem UHP-Lampe, emittiert eine geringe Menge das Gerät mindestens eine Stunde ausgeschaltet war, UV-Strahlung.
  • Page 51: Lage Der Bedienelemente

    XV-Z10000 Lage der Bedienelemente Projektor (Vorder- und Draufsicht) MENU-Taste Einstelltasten (", ', \, |) Für die Anzeige des Justierungs- und Für die Wahl der Einstellungsbildschirms. Menüpunkte. ENTER-Taste RESIZE-Taste Für die Einstellung der Für das Umschalten der gewählten oder Bildwandgrö§e (SEITENBA., eingestellten Menüpunkte.
  • Page 52 XV-Z10000 INPUT 3-Anschluss Anschluss für ein Videogerät mit einem S- Projektor (Hintersicht) VIDEO-Anschluss. INPUT1-Anschlüsse RS-232C-Anschluss Anschlüsse für Für die Bedienung des Komponenten- und RGB- Projektors über Signale. Computers. INPUT 5-Anschluss DC 12 V OUTPUT- Anschluss für DVI-Digital-, Anschluss Computer-RGB- und COMPONENT-Signale.
  • Page 53 XV-Z10000 Fernbedienung (Vordersicht) Netz-Tasten (ON/OFF) Schaltet die Stromversorgung ein oder aus. KEYSTONE-Taste Für die Trapezkorrektur oder die Einstellung der vertikalen Größe. MENU-Taste Für die Anzeige des Justierungs- und ENTER-Taste Einstellungsbildschirms. Für die Einstellung der gewählten oder eingestellten Menüpunkte. Einstelltasten (', ", \, |) Für die Wahl der Menüpunkte.
  • Page 54: Reichweite Der Fernbedienung

    XV-Z10000 Reichweite der Fernbedienung Der Projektor kann mittels der Fernbedienung innerhalb der Fernbedienung in der Abbildung gezeigten Bereiche gesteuert werden. Hinweis 30ß • Das Signal von der Fernbedienung kann für eine einfache Bedienung von der 30ß 45ß Bildwand reflektiert werden. Die tatsächliche Reichweite des Signals kann je nach Bildwandmaterial unterschiedlich sein.
  • Page 55 XV-Z10000 Pin-Belegung Verbindungs-Pin-Zuweisungen DVI-I (INPUT 5 / DIGITAL INPUT)-Anschluss: 29-pol. Stecker • • • • • DVI-Digital-Eingang Pin Nr. Signal Pin Nr. Signal T.M.D.S.-Daten 2- Zündkerzenerkennung T.M.D.S.-Daten 2+ T.M.D.S.-Daten 0- T.M.D.S.-Daten 2-Schutz T.M.D.S.-Daten 0+ 24 23 18 17 Nicht angeschlossen T.M.D.S.-Daten 0-Schutz...
  • Page 56 XV-Z10000 Abmessungen Ansicht von hinten Ansicht von Ansicht von Ansicht von der Seite oben der Seite Ansicht von vorne Ansicht von unten Einheit:mm...
  • Page 57: Entfernen Der Hauptteile

    XV-Z10000 ENTFERNEN DER HAUPTTEILE 1. Ausbau der oberen Abdeckung 1-1. Die sechs Sicherungsschrauben losdrehen. 2-1. Die beiden Schrauben losdrehen, dann die LED- 1-2. An den seitlichen Pfeil A an der Gehäuseunter- Platine entfernen. seite hineindrücken und die hintere Abdeckung 2-2. Die Schraube losdrehen und die R/C-Platine ent- anheben.
  • Page 58 XV-Z10000 2. Ausbau des Kühlgebläses und der Platineneinheit 3-1. Die zehn Steckverbinder abziehen. 3-2. Die beiden Schrauben losdrehen und die Lampenfassung entfernen. 3-3. Die beiden Schrauben losdrehen und das Kühlgebläse entfernen. 3-4. Die vier Schrauben losdrehen und die Platineneinheit entfernen.
  • Page 59 XV-Z10000 3. Ausbau der Rückwand, der PC-Einheit, des Kühlschachts und der Hauptplatineneinheit 4-1. Die beiden Schrauben losdrehen. 4-2. Die drei Schrauben losdrehen und die Abdeckplatte entfernen. 5-1. Die beiden Schrauben losdrehen. 5-2. Die vier Sechskanthalterungen entfernen, dann die Abdeckplatte entfernen.
  • Page 60 XV-Z10000 4. Entfernen der Netzteilabdeckung, der Netz-/Vorschaltgeräte-Einheit sowie des Netzteils. Die sieben Schrauben losdrehen und die Netzteilabdeckung entfernen. 10-1. Die beiden Schrauben losdrehen. 10-2. Die vier weißen Halter entfernen, dann das Netzteil abnehmen. Die vier Schrauben losdrehen, dann das Netzteil entfernen.
  • Page 61 XV-Z10000 5. Ausbau der Optikmechanismus-Einheit und der R/C-Platineneinheit Die sechs Schrauben losdrehen und die Optikmechanismus-Einheit entfernen. Die Schraube losdrehen und die R/C-Platineneinheit entfernen. Optikmechanismus-Einheit R/C-Platineneinhei...
  • Page 62 XV-Z10000 6. Ausbau von Lampeneinheit, Farbeinstellscheiben-Gebläse, Auslaßgebläse, Luftkanal, Abschirmblech und Bildformatiererplatine Die drei Schrauben losdrehen und die Lampeneinheit entfernen. Die beiden Schrauben losdrehen und das Farbeinstellscheiben-Gebläse entfernen. Die drei Schrauben losdrehen und das Auslaßgebläse entfernen. 17-1. Die beiden Schrauben losdrehen und das Bimetall entfernen.
  • Page 63: Rückstellen Des

    • Die Lampe wurde über 2.000 Stunden • Die Lampe austauschen. Sie können ausgeschaltet und der Projektor auf verwendet. die Lampe auch bei einem von Sharp Betriebsbereitschaft geschaltet. autorisierten Händler für Projektoren "LAMP." und " " blinken rot in der...
  • Page 64: Beschreibung Der Optik-Einheit

    XV-Z10000 Beschreibung der Optik-Einheit Anordnung der optischen Komponenten und zugehörigen Bauteile (Draufsicht) Projektionsobjektiv Prisma DMD-Chips Kondensatorlinse IR-Arretierspiegel Lichtschacht Übertragungslinse Faltspiegel Kondensatorlinse Farbfilter Lampe Gegenstand Beschreibung 1 Lampe Gleichstrom-Lampe mit Parabolreflektor 2 Kondensatorlinse, IR-Arretier- Die Kondensatorlinse führt das Licht von der Lampe zur Endoberfläche des spiegel und Lichtschacht Lichtschachts via dem IR-Arretierspiegel.
  • Page 65 XV-Z10000 Einstellung der Spiegel Einstellung des Anzeigebereichs am Bildschirm vornehmen, um Dunkelbereiche am äußeren Bildschirmrand zu ver- meiden. 1. Die obere Abdeckung abnehmen, so daß die Optikeinheit sichtbar wird. Nur Weiß am Bildschirm anzeigen. 2. Die Abdeckung 1 der Spiegeleinstellplatte an der Unterseite rechts vom Projektionsobjektiv entfernen.
  • Page 66 XV-Z10000 Wenn die DMD-Einheit ausgewechselt wurde Hinweis: Der DMD-Chip und die Bildformatiererplatine werden zur gleichen Zeit geliefert. Es wird ausschließlich der DMD-Chip ausgewechselt. Beziehen Sie sich beim Auswechseln der Bildformatiererplatine bitte auf den Abschnitt "AUSBAU DER WICHTIGSTEN BAUTEILE". Die hintere Brennweite des Projektionsobjektivs braucht nicht eingestellt zu werden. Wenn die Brennpunkteinstellung jedoch unzufriedenstellend ist, muß...
  • Page 67: Elektrische Einstellung

    XV-Z10000 ELEKTRISCHE EINSTELLUNGEN Einen Signalgenerator bzw. einen PC oder Macintosh-Computer an den Projektor anschließen, um die Signale zuzuführen, die in den Einstellbedingungen aufgeführt sind. Einstellgegenstand Einstellbedingungen Einstellverfahren EEPROM wird 1. Die folgenden Einstellungen ausführen: 1. Den Netzschalter ein- initialisiert Den Schalter SW2002 drücken, um in den Prozeß- schalten und das Gerät für...
  • Page 68 XV-Z10000 Einstellgegenstand Einstellbedingungen Einstellverfahren 1. Durch Wahl von AUTO über Steuerschalter oder Videohelligkeit/ 1. Die nachfolgende Gruppe Fernbedienung nach der Signaleingabe erfolgt Kontrast- bzw. die Positionen wählen: einstellung automatische Einstellung. Gruppe: VIDEO1 Position: AUTO Einstellung des 1. Geteiltes Farbbalkensignal 1. Die folgende fixierte Einstellung überprüfen: Video-Farbtons an INPUT 4 eingeben.
  • Page 69 XV-Z10000 Einstellgegenstand Einstellbedingungen Einstellverfahren Überprüfung der 1. Das RGB-Signal zuführen. 1. L4 von der Prozeßmodus-Leitung wählen. RGB- Die Leistung von Bild, Helligkeit, Rot, Blau, Takt, Leistungswerte Phase, Horizontal- und Vertikalposition überprüfen. überprüfen. Leistung des 1. OFF von der Prozeßmodus-Leitung wählen.
  • Page 70 XV-Z10000 Einstellung der PC-Platine 1. Initialisierung des EEPROM 1) Den Schalter SW2002 drücken, um den Prozeßmodus aufzurufen. 2) Den S1-Befehl am SSS-Menü ausführen. (Der S1-Befehl dient dazu, die Platine alleine zu initialisieren. Der S2-Befehl darf allerdings nicht eingegeben werden, da hierdurch auch alle anderen Einstelldaten der Platine initialisiert werden.)
  • Page 71 XV-Z10000 Verfahren der Farbhelligkeitseinstellung Einstellung in den folgenden beiden Schritten 1. Einstellparameter DLP GAMMA 2. Eingangssignal: Komponentenvideo 75 % Weißsignal, 0,7 ±0.05 Vss (ohne synchronisierten Teil) 3. DLP GAMMA-Anfangswert 6 4. Einstellverfahren 1 DLP Den Zahlenwert des GAMMA-Parameters von Anfangswert 6 auf 0 verstellen.
  • Page 72 XV-Z10000 Prozeßmenü 1 Group Sub Group Subject Adjust PC Image A/D (RGB) R-BRIGHT G-BRIGHT B-BRIGHT AD-AUTO A/D (COMP) G-BRIGHT CB-OFFSET CR-OFFSET A/D AUTO Adjust HDDE formatter CW-INDEX DLP-GAMMA R-BRIGHT G-BRIGHT B-BRIGHT R-GAIN G-GAIN B-GAIN Adjust VIDEO Image VIDEO1 NTSC-H PICTURE...
  • Page 73 XV-Z10000 Prozeßmenü 2 Group Sub Group Subject INITIAL SETTING TIME LAMP Sample Pattern PATTERN RGB(50) CROSS STEP COLOR Adjust CVIC CVIC MODE -PROGRESSIVE MD SW PTGSW C-TESTSW C-ILG-LY C-MOD-LY C-VE-LY CVIC ENH-PLUS -ENHANCE-VIDEO ENH-MINUS CVIC ENH-PLUS -ENHANCE-HDTV ENH-MINUS CVIC MODE...
  • Page 74 XV-Z10000 Prozeßmenü 3 Group Sub Group Subject Adjust CVIC CVIC TBL-NO -PTG TESTSW ENABLE MV-F VDDYP CVIC CMS-HUE-R -CMS-HUE CMS-HUE-Y CMS-HUE-G CMS-HUE-C CMS-HUE-B CMS-HUE-M CVIC CMS-SAT-R -CMS-SAT CMS-SAT-Y CMS-SAT-G CMS-SAT-C CMS-SAT-B CMS-SAT-M CVIC CMS-VAL-R -CMS-VAL CMS-VAL-Y CMS-VAL-G CMS-VAL-C CMS-VAL-B CMS-VAL-M...
  • Page 75: Fehlersuchtabelle

    XV-Z10000 FEHLERSUCHTABELLE Überprüfung der allgemeinen Leistung Blinkt die POWER-LED rot NEIN oder blau? Zur "Überprüfung des Netzgeräts" weitergehen. Wird das Gerät durch die NEIN Netztaste auf der Fern- bedienung eingeschaltet? Zur "Überprüfung der peripheren Micro-computer- Komponenten" und "Überprüfung der PC- Platine"...
  • Page 76 XV-Z10000 Überprüfung der Stromversorgung Sind alle Steckver- NEIN bindungen innerhalb der Stromversorgung fest angeschlossen? Die Steckverbinder CN7105, 7103, 7101 und 7102 gut einstecken. NEIN Ist die Lampenabdeckung vollkommen geschlossen? Die Lampenabdeckung mit den Schrauben gut festziehen. NEIN Funktioniert der Bimetallschalter?
  • Page 77 XV-Z10000 Überprüfung der PC- Platine Wird das Benutzermenü richtig angezeigt? NEIN Den normalen Signalfluß überprüfen. Der Signalfluß Die Bildschirmanzeige vom CVIC_IC zum Panel-Ausgangsanschluß ist überprüfen. gleich wie für die Komponente und die Videosignale. Deshalb werden die Leitungssignale nach CVIC nicht geprüft. (Die 480i- und 580i- Komponentensignale sind nicht miteingeschlossen.)
  • Page 78 XV-Z10000 Überprüfung des RGB- Eingangs Das synchron-getrennte DTV RGB-Signal dem INPUT1 oder INPUT2 zuführen. (Die 480i- und 580i-Komponentensignale sind nicht miteingeschlossen.) INPUT1 oder INPUT2 mit der Taste auf der Frontplatte oder auf der Fernbedienung anwählen. NEIN Erscheint das Bild? Überprüfen, ob das Videoeingangssignal wie spezifiziert ist.
  • Page 79 XV-Z10000 Überprüfung des Videoeingangs Sicherstellen, da§ die Eingangssignaleinstellung wie spezifiziert ist. NEIN Liegt am Anschlu§ des C8077 ein Videosignal an? Defekte Eingangsplatine. Das Synchronsignal berpr fen. IC8025 oder IC8004 sind defekt. Überprüfung der Eingangssignaleinstellung Ist die NEIN Eingangssignaleinstellung wie spezifiziert? Das spezifizierte Signal anw hlen.
  • Page 80 XV-Z10000 Überprüfung des Synchronsignals Liegt am TL8134 ein NEIN Vertikal-Synchronsignal Liegt am TL8133 ein NEIN Horizontal-Synchronsignal Die Eingangssignal- einstellung überprüfen. Defekte Eingangsplatine. Liegt am TL8131 ein NEIN Vertikal-Synchronsignal Liegt am TL8130 ein NEIN Horizontal-Synchronsignal IC8302, IC8325, IC8299 oder ihre peripheren Schaltkreise sind defekt.
  • Page 81 XV-Z10000 Überprüfung des RGB- Signals Ist der Signaltyp auf RGB eingestellt? Auf das RGB-Signal NEIN einstellen. Den Prozeßmodus abrufen. R, G und B separat am Mustermenü anwählen. Zur "Überprüfung der peripheren Schaltkreise des GA4" weitergehen. Den Signalgenerator in den Abstufungssignal-...
  • Page 82 XV-Z10000 Überprüfung der peripheren Schaltkreise des GA4 Den Prozeßmodus abrufen und R, G und B separat am Mustermenü anwählen. Liegen spezifizierte R-, G- und B-Videoausgangs- signale an? Ende der Überprüfung für NEIN die peripheren Schaltkreise des GA4. Sind die gemessenen Signale mit den vom Mustermenü...
  • Page 83 XV-Z10000 Überprüfung der Komponenteneingänge (außer für 480i) Das Komponentensignal dem INPUT1 oder INPUT2 zuführen. INPUT1 oder INPUT2 mit der Taste auf der Frontplatte oder auf der Fernbedienung anwählen. NEIN Erscheint das Bild? Zur „Überprüfung des SOG -Schaltkreises“ weitergehen. Sind die Farben wie...
  • Page 84 XV-Z10000 Überprüfung des SOG- Schaltkreises Das Signal mit dem Oszilloskop am TL8136 messen. Wird das Farbsynchronsignal zeitlich wiedergegeben? NEIN Es besteht kein Problem mit dem SOG-Schaltkreis. Mit dem Oszilloskop am Anschluß des C8069 messen. NEIN Liegt das Y-Signal einschließlich dem Synchronsignal an? Zur „Überprüfung der...
  • Page 85 XV-Z10000 Überprüfung des Videoausgangs Das Farbbildsignal dem INPUT4 zuführen. INPUT4 mit der Taste auf der Frontplatte oder auf der Fernbedienung anwählen. VIDEO als Signaltyp am Benutzermenü wählen. NEIN Erscheint das Bild? Zur „Überprüfung des Videosynchronsignals“ Bestehen Bildstörungen? weitergehen. NEIN NEIN Zur „Überprüfung des...
  • Page 86 XV-Z10000 Das VPC-Taktsignal (IC8338) am TL8004 messen. NEIN Ist das Taktsignal wie spezifiziert? Defekter IC8338. Zur „Überprüfung des Videosynchronsignals“ weitergehen. Der IC8025 oder sein peripherer Schaltkreis ist defekt. Überprüfung des Videosynchronsignals Mit dem Oszilloskop das Signal am TL8140 messen. (Das Vertikal- Synchronsignal überprüfen.)
  • Page 87 XV-Z10000 Überprüfung des D-SUB-Eingangs Das PC-RGB-Signal dem INPUT5 zuführen. INPUT5 als Eingang wählen. Sicherstellen, das R-, G- und B- NEIN Erscheint das Bild? Signale an den Stiften (126), (136) und (146) des IC8004 anliegen. Der D-SUB-Stecker NEIN Bestehen Bildstörungen? oder sein peripherer Liegen die Signale R, G und B an? Schaltkreis ist defekt.
  • Page 88 XV-Z10000 Überprüfung der Lampenfunktion Die Lampe leuchtet nicht auf. Wird bei Einschalten des Gerätes ein Entladungsgeräusch Ist die Lampe oder die NEIN wahrgenommen? Farbeinstellscheiben- NEIN Leitungsfassung nicht Die Fassungen gut richtig angebracht? befestigen. Die Lampe oder die Farbeinstellscheibe auswechseln. Laufen die Kühlgebläse NEIN ordnungsgemäß?
  • Page 89 XV-Z10000 Keine Horizont alsynchronisation Ist der Terminal- Eingangsanschluß wie spezifiziert? Ist das Kabel Das vorgeschriebene fest angeschlossen? Kabel benutzen, NEIN einstecken und gut befestigen. Liegt am Stift (14) des NEIN IC2506 ein Horizontal- Synchronsignal an? Die Leitung zwischen dem IC2506 und dem Eingangsterminal überprüfen.
  • Page 90 XV-Z10000 Überprüfung des IC3504 (3D- Rauschunterdrückung) und seiner peripheren Schaltkreise. Liegen Eingangssignale an NEIN den Stiften (88) (Y-Signal) und (96) (C-Signal) von IC3504 an? Den Eingangssignal schaltkreis des IC2505 und seine peripheren Schaltkreise überprüfen. Liegen Ausgangssignale NEIN an den Stiften (84) (Y-...
  • Page 91 XV-Z10000 Überprüfung der Komponenten- und RGB-Eingänge Liegen Signale an den NEIN Stiften (34), (36) und (38) von IC2505 an? NEIN Den Eingangssignal schaltkreis oder den IC2505 und seine Es liegen keine RGB- peripheren Schaltkreise Farben vor. überprüfen. Den Schaltkreis der nicht...
  • Page 92: Chassis Layout

    XV-Z10000 CHASSIS LAYOUT / CHASSIS-ANORDNUNG...
  • Page 93 XV-Z10000...
  • Page 94: Block Diagram

    XV-Z10000 BLOCK DIAGRAM / BLOCKSCHALTBILD...
  • Page 95 XV-Z10000...
  • Page 96: Overall Wiring Diagram

    XV-Z10000 OVERALL WIRING DIAGRAM / GESAMTSCHALTPLAN...
  • Page 97 XV-Z10000...
  • Page 98: Description Of Schematic Diagram

    XV-Z10000 DESCRIPTION OF BESCHREIBUNG DES SCHEMATIC DIAGRAM SCHEMATISCHEN SCHALTPLANS VOLTAGE MEASUREMENT CONDITION: SPANNUNGSMESSUNGEN: 1. Voltages at test points are measured at the 1. Spannungen an den Prüfpunkten werden bei einer Netzspannung von 220V gemessen, Signale werden supply voltage of AC 220V. Signals are fed by a für die Wartung mit einem Farbbalken-Signal generator...
  • Page 99: Waveforms

    XV-Z10000 WAVEFORMS / WELLENFORMEN 1 P3580 32 2 P3580 34 3 P3580 4 4 P3580 47 (VIDEO AC) (Y-signal) (CHROMA signal) (RGB) H : 20µ sec/div H : 10µ sec/div H : 10µ sec/div H : 20µ sec/div V : 500mV/div V : 0.2V/div...
  • Page 100: Schematischer Schaltplan

    XV-Z10000 Ë MAIN UNIT / HAUPT-EINHEIT -1/5...
  • Page 101 XV-Z10000...
  • Page 102 XV-Z10000 Ë MAIN UNIT / HAUPT-EINHEIT -2/5...
  • Page 103 XV-Z10000...
  • Page 104 XV-Z10000 Ë MAIN UNIT / HAUPT-EINHEIT -3/5...
  • Page 105 XV-Z10000...
  • Page 106 XV-Z10000 Ë MAIN UNIT / HAUPT-EINHEIT -4/5...
  • Page 107 XV-Z10000...
  • Page 108 XV-Z10000 Ë MAIN UNIT / HAUPT-EINHEIT -5/5...
  • Page 109 XV-Z10000...
  • Page 110 XV-Z10000 Ë KEY UNIT / TASTE-EINHEIT...
  • Page 111 XV-Z10000 Ë R/C RECEIVER (Front) Unit / EINLASSEINHEIT (Vorder) Ë R/C RECEIVER (Rear) Unit / EINLASSEINHEIT (Hinter)
  • Page 112 XV-Z10000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-1/7...
  • Page 113 XV-Z10000...
  • Page 114 XV-Z10000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-2/7...
  • Page 115 XV-Z10000...
  • Page 116 XV-Z10000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-3/7...
  • Page 117 XV-Z10000...
  • Page 118 XV-Z10000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-4/7...
  • Page 119 XV-Z10000...
  • Page 120 XV-Z10000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-5/7...
  • Page 121 XV-Z10000...
  • Page 122 XV-Z10000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-6/7...
  • Page 123 XV-Z10000...
  • Page 124 XV-Z10000 Ë FORMATTER UNIT / FORMATTER-EINHEIT-7/7...
  • Page 125 XV-Z10000...
  • Page 126 XV-Z10000 Ë POWER UNIT / NETZTEINHEIT...
  • Page 127 XV-Z10000...
  • Page 128 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-1/9...
  • Page 129 XV-Z10000...
  • Page 130 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-2/9...
  • Page 131 XV-Z10000...
  • Page 132 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-3/9...
  • Page 133 XV-Z10000...
  • Page 134 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-4/9...
  • Page 135 XV-Z10000...
  • Page 136 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-5/9...
  • Page 137 XV-Z10000...
  • Page 138 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-6/9...
  • Page 139 XV-Z10000...
  • Page 140 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-7/9...
  • Page 141 XV-Z10000...
  • Page 142 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-8/9...
  • Page 143 XV-Z10000...
  • Page 144 XV-Z10000 Ë PC I/F UNIT / PC-I/F-EINHEIT-9/9...
  • Page 145 XV-Z10000...
  • Page 146 XV-Z10000 Ë LED UNIT/ LED-EINHEIT...
  • Page 147: Printed Wiring Board Assemblies

    XV-Z10000 PRINTED WIRING BOARD ASSEMBLIES LEITERPLATTENEINHEITEN Power Unit (Component Side) Netzteinheit (Bestückungsseite) Power Unit (Wiring Side) Netzteinheit (Leiterbahnseite)
  • Page 148 XV-Z10000 Main Unit (Component Side) Haupt-einheit (Bestückungsseite)
  • Page 149 XV-Z10000 Main Unit (Wiring Side) Haupt-einheit (Leiterbahnseite)
  • Page 150 XV-Z10000 Key Unit (Component Side) Taste-Einheit (Bestückungsseite) R/C Receiver (Rear) Unit (Component Side) Einlasseinheit (Hinter) (Bestückungsseite) R/C Receiver (Front) Unit (Component Side) Einlasseinheit (Vorder) (Bestückungsseite) LED Unit (Component Side) LED-Einheit (Bestückungsseite)
  • Page 151 XV-Z10000 Key Unit (Wiring Side) Taste-Einheit (Leiterbahnseite) R/C Receiver (Rear)Unit (Wiring Side) Einlasseinheit (Hinter) (Leiterbahnseite) R/C Receiver (Front)Unit (Wiring Side) Einlasseinheit (Vorder) (Leiterbahnseite) LED Unit (Wiring Side) LED-Einheit (Leiterbahnseite)
  • Page 152 XV-Z10000 PC I/F Unit (Component Side) PC-I/F-einheit (Bestückungsseite)
  • Page 153 XV-Z10000 PC I/F Unit (Wiring Side) PC-I/F-einheit (Leiterbahnseite)
  • Page 154 XV-Z10000 FORMATTER Unit (Component Side) FORMATTER-einheit (Bestückungsseite) FORMATTER Unit (Wiring Side) FORMATTER-einheit (Leiterbahnseite)
  • Page 155: Parts Listë Electrical Parts

    Contact your nearest SHARP Parts Distributor. For location of SHARP Parts Distributor, 5. KODE 6. QUANTITÄT Please call Toll-Free; 1-800-BE-SHARP in CANADA: Contact SHARP Electronics of Canada Limited Phone (416) 890-2100. MARK: SPARE PARTS-DELIVERY SECTION MARKIERUNG : ERSATZTEILE-LIEFERUNG Ref. No.
  • Page 156 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code D2523 VHDKDS226//-1Y J KDS226 DUNTKA471DE05 D2524 VHDHSU119//-1Y J HSU119 D2525 VHDKDS226//-1Y J KDS226 MAIN UNIT(Continued) D2802 VHDDAN202K/-1Y J DAN202K D2805 RH-EX1271CEZZY J Zener Diode Q2004 VSRN4904///-1Y J RN4904...
  • Page 157 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code C2606 VCKYCY1EF104ZY J 0.1 Ceramic DUNTKA471DE05 C2607 VCKYCY1EF104ZY J 0.1 Ceramic C2803 VCCCCY1HH101JY J 100p Ceramic MAIN UNIT(Continued) C2805 VCCCCY1HH101JY J 100p Ceramic C2812 VCKYCY1CB104KY J 0.1 Ceramic C2021 VCKYCY1CB104KY J 0.1...
  • Page 158 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code R2072 VRS-CA1JF103JY J 10k 1/16W Metal Oxide DUNTKA471DE05 R2073 VRS-CB1JF103JY J 10k 1/16W Metal Oxide R2074 VRS-CY1JF473JY J 47k 1/16W Metal Oxide MAIN UNIT(Continued) R2075 VRS-CB1JF102JY J 1k...
  • Page 159 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code R2822 VRS-CY1JF102JY J 1k 1/16W Metal Oxide DUNTKA471DE05 R2825 VRN-CY1JF153DY J 15k 1/16W Metal Film R2832 VRS-CY1JF472JY J 4.7k 1/16W Metal Oxide MAIN UNIT(Continued) R2847 VRS-CY1JF392JY J 3.9k 1/16W Metal Oxide...
  • Page 160 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code FB2819 RBLN-0064TAZZY J Ferrite Bead DUNTKA471DE05 FB2820 RBLN-0064TAZZY J Ferrite Bead FB2821 RBLN-0064TAZZY J Ferrite Bead MAIN UNIT(Continued) FB3507 RBLN-0064TAZZY J Ferrite Bead FB2809 RBLN-0058TAZZY J Ferrite Bead...
  • Page 161 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code DUNTKA472DE05 DUNTKA474DE5 KEY UNIT R/C REAR UNIT CAPACITOR CAPACITORS C2202 VCKYCY1CB104KY J 0.1 Ceramic C2404 VCKYCY1EF104ZY J 0.1 Ceramic C2406 VCEAPF0JW107MY J 100 6.3V Electrolytic RESISTORS RESISTORS R2201 VRS-CY1JF562JY J 5.6k 1/16W Metal Oxide...
  • Page 162: Formatter Unit

    XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code C9101 VCKYCY1EB104KY J 0.1 25V Ceramic DUNTKB474FE01 C9102 VCKYCY1EB104KY J 0.1 25V Ceramic C9103 VCKYCY1EB104KY J 0.1 25V Ceramic FORMATTER UNIT C9104 VCKYCY1EB104KY J 0.1 25V Ceramic C9105 VCKYCY1EB104KY J 0.1...
  • Page 163 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code C9542 VCKYCY1EB104KY J 0.1 Ceramic DUNTKB474FE01 C9543 VCKYCY1EB104KY J 0.1 Ceramic C9544 VCKYCY1EB104KY J 0.1 Ceramic FORMATTER UNIT(Continued) C9545 VCKYCY1EB104KY J 0.1 Ceramic C9546 VCKYCY1EB104KY J 0.1 Ceramic C9233 VCKYCY1EB104KY J 0.1...
  • Page 164 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code SC9002 QSOCN0687FJZZY J Socket, 50pin DUNTKB474FE01 S9101 QSW-S0203TAZZY J Slide Switch S9102 QSW-S0203TAZZY J Slide Switch FORMATTER UNIT(Continued) R9208 VRS-CY1JF102JY J 1k 1/16W Metal Oxide R9209 VRS-CY1JF111FY...
  • Page 165 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code C7152 95C0C195E1040 J 0.1 50V Ceramic RDENCA026WJZZ C7201 95CC3124ML181 J 180 400V Eleectrolytic C7202 95C0C157R1010 100p Ceramic POWER UNIT(Continued) C7203 95C0C1A9R1020 1000p 1kV Ceramic C7205 95C0C1Q2E1030 J 0.01...
  • Page 166 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code R7309 95C0R3Q8S1030 J 10k 1/16W Chip1608 RDENCA026WJZZ R7351 95C0R3Q4S2220 J 2.2k 1/16W Chip1608 R7352 95C0R3Q4S8200 J 82 1/16W Chip1608 POWER UNIT(Continued) R7353 95C0R3Q1V2710 J 270 1/8W Chip2012...
  • Page 167 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code D8048 9DK001-30015 J MA157A CPCi-A004CE01 D8049 9DK001-30018 J 1SS187 (D3) PC I/F UNIT PACKAGED CIRCUITS J CX-5F(6MHz ± 50PPM) X8001 9DK001-80012 INTEGRATED CIRCUITS X8003 9DK001-80011 J FXO-31FL(1.8432MHz)
  • Page 168 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code C8562 9DK001-42094 J 0.1 Ceramic CPCi-A004CE01 C8563 9DK001-42094 J 0.1 Ceramic C8564 9DK001-40089 J 47 6.3V Electrolytic PC I/F UNIT(Continued) C8565 9DK001-42094 J 0.1 Ceramic C8566 9DK001-42123...
  • Page 169 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code FL8023 9DK001-50113 1/4W Chip3216 CPCi-A004CE01 FL8029 9DK001-50113 1/4W Chip3216 FL8039 9DK001-50113 1/4W Chip3216 PC I/F UNIT(Continued) FL8040 9DK001-50113 1/4W Chip3216 FL8041 9DK001-50113 1/4W Chip3216 C8752 9DK001-42113 J 4.7...
  • Page 170 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code R8701 9DK001-50257 J 75 1/16W Chip1608 CPCi-A004CE01 R8704 9DK001-50185 J 10k 1/16W Chip1608 R8741 9DK001-50159 J 22 1/16W Chip1608 PC I/F UNIT(Continued) R8745 9DK001-50149 1/16W Chip1608 R8747 9DK001-50149...
  • Page 171 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code CPCi-A004CE01 PC I/F UNIT(Continued) MISCELLANEOUS PARTS J8003 9DK001-60057 J Connector,55176-3091 J8005 9DK001-60058 J Connector,FH12-50S-0.5SH P8001 9DK001-60078 J Connector,74320-1007 P8404 9DK001-60069 J Connector,179029-2,60pin AS P8405 9DK001-60069 J Connector,179029-2,60pin AS...
  • Page 172: Ë Cabinet And Mechanical Parts

    — PCLiC1034CEKZ J Cover Clip 1-1-2 GCOVA1981CESA J Rear R/C Cover PCLiC1035CEKZ J Cover Clip Plun 1-1-3 HBDGS3153CESA J SHARP VISION Badge SSAKA1109CEZZ J Cover Sack 1-1-4 HiNDP5799CESA J Lens Warning Label 1-1-5 HiNDP5845CESB J Operation Indication CDUC-0154CE01 J HDDE Duct Ass’y...
  • Page 173 XV-Z10000 CABINET AND MECHANICAL PARTS/ GEHÄUSE UND MECHANISCHE BAUTEILE 11-3 1-1-5 11-1 1-1-4 1-13 1-1-6 1-1-3 1-16 11-4 1-1-1 1-20 1-1-2 1-14 11-2 1-1-9 1-20 1-15 1-10 1-20 1-1 1 1-20 1-1-8 1-20 1-19 1-12 1-1-10 1-20 12-2 12-2 1-18...
  • Page 174 XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code CABINET AND MECHANICAL PARTS OPTICS MECHANISM PARTS (Continued) LX-BZ3266CEFD J Screw, x20 CCHSK0103CE02 J Optics Mechanism Ass’y LX-EZ3011CEFD J Screw, x3 9HN-3623-0042 J Cover Ass’y NFANS0006CE00 J Color Wheel Fan...
  • Page 175 XV-Z10000 OPTICS MECHANISM PARTS/ TEILE FÜR OPTIKMECHANISMUS 6-19 6-20 6-21 6-15 6-16 6-16 6-12 6-22 8-13 6-11 6-14 6-13 6-10 6-17 6-18 8-11 8-11 8-11 8-12 8-10 8-11 8-14...
  • Page 176: Ë Accessories Parts

    XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING PARTS SUPPLIED ACCESSORIES (NOT REPLACEMENT ITEM) QACCBA012WJPZ J AC Cord (for UK) SPAKCA558WJZZ – Packing Case — å QACCDA010WJPZ J AC Cord SPAKPA123WJZZ – Polystyrene Cover —...
  • Page 177: Packing Of The Set

    XV-Z10000 Ref. No. Part No. Description Code Ref. No. Part No. Description Code PACKING OF THE SET / VERPACKEN DES GERÄTS Polystyrene Bag (SSAKA0170CEZZ :XV-Z10000U) (SSAKA111CEZZ:XV-Z10000E/K) Operation Manual Terminal Cover Ass'y (TiNS-A440WJZZ :XV-Z10000U) (CCOVA1985CE02) (TiNS-A442WJZZ:XV-Z10000E/K) (TiNS-A443WJZZ:XV-Z10000E/K) (TiNS-A452WJZZ) Questionnaire Card (TCADEA029WJZZ)
  • Page 178 Code Ref. No. Part No. Description Code COPYRIGHT © 2003 BY SHARP CORPORATION ALL RIGHTS RESERVED. No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without prior written permission of the publisher.

Table of Contents