Maintenance; General Maintenance; Spool Replacement; Starting And Stopping - Ryobi CS30 Operator's Manual

30cc string trimmers and brushcutters
Hide thumbs Also See for CS30:
Table of Contents

Advertisement

STARTING AND STOPPING
See Figures 21 - 23.
TO START A COLD ENGINE:
DO NOT squeeze the throttle trigger until the engine starts
ano runs.
r Lay the trimmer on a flat, bare surface.
r PRIME - Press the primer bulb 7 times.
r SET the start lever to the START posiiion.
I PULL the rope until the engine starts.
r Wait 6-1 0 seconds, then squeeze the trigger to run.
NOTE: Squeezing the throttle trigger releases the start lever
to the RUN position.
TO START A WARM ENGINE:
PULL the rope until the engine starts.
TO STOP THE ENGINE:
Press and hold the switch in the stop " @ " position until
the engine stops.
PRIMER B ULI
Fi1.22
START P()SITI()N
START LEVER
RUN
P0srTt0N
START LEVER
Fig.
Z J
I wnnrurruc'
When servicing, use only identical replacement parts.
Use of any other pads may create a hazard or cause
^ r
d il ^+
dr m. ^a
A wnnuHc'
Always wear safety goggles or safety glasses with side
shields during tool operation. lf operation is dusty, also
wear a dust mask.
A wmrurruc'
Before inspecting, cleaning, or servicing the machine,
shut off engine, wait for all moving parts to stop, and
disconnect spark plug wire and move it away from spark
plug. Failure to follow these instructions can result in
serious personal injury or property damage.
GENERAL MAINTENANCE
Avoid using solvents when cleaning plastic parts. Most
plastics are susceptible to damage from various types of
commercial solvents and may be damaged by thelr use. Use
clean cloths to remove dirt, dust, oil, grease, etc.
A wnnrurruc,
Do not at any time let brake fluids, gasoline, petroleum-
based products, penetrating oils, etc., come in contact
with plastic parts. Chemicals can damage, weaken or
destroy plastic which may result in serious personal
rnlury.
You can often make adjustments and repairs described here.
For other repairs, have the trimmer serviced by an authorized
service dealer.
SPOOL REPLACEMENT
EZ WINDTM TAP ADVANCE SYSTEM
NEW PREWOUND
SPOOL
See Figures 24 - 25.
lf replacing string only, refer to String Replacement later
tn this manual.
Use only .080 in. diameter trimmer line. Use original manu-
facturer's replacement string for bbst performance.
I Stop the engine and disconnect the spark plug wire. Hold
the string head and turn the spool retainer clockwise to
remove.
Fig.24
INSERT INTO
STRING HEAD
Fi g. 25
I Remove the empty spool from the string head. Keep the
spring attached to the spool.
I Make sure the two strings are captured in the slots op-
posite each other on the new spool. Make sure the end
of each string is extended approximately 6 in. beyond
each slot.
I Align the slot(s) on the spool to the eyelet(s) on the string
head housing. Push down and turn the spool in the nec-
essary direction to align the slot(s).
r Make sure the string head and the spool retainer are
installed on the drive shaft. Turn the soool retainer coun-
terclockwise to secure.
I Slide strings into the housing eyelets and pull outward to
rotate the spool into the cutting position.
r Push the spool retainer down while pulling on string(s)
to manually advance the string and to check for proper
assembly of the string head.
1 9

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Bc30Ss30Ry30522Ry30923Ry30542Ry30943 ... Show all

Table of Contents