Korg m3 Operation Manual page 223

Appendices
• Set a destination measure that is outside of the
source range.
Destination is empty
Meaning: When editing, the track or pattern that was
specified as the destination contains no musical data.
To solve this problem:
• Select a track or pattern that contains musical data.
Destination measure is empty
Meaning: The measure that was specified as the
destination contains no data.
• Specify a destination measure that contains data.
Destination multisample already exists
Meaning: A multisample already exists at the
destination (save location) multisample.
• Either delete the multisample at the destination
(save location), or change the save destination
multisample number.
Destination multisample and source multisample
are identical
Meaning: The same multisample is selected for the
source and destination.
• Select different multisamples for the source and
destination.
Destination sample already exists
Meaning: A sample already exists at the destination
(save location).
• Either delete the sample at the destination (save
location), or change the save destination sample
number.
Meaning: The save-destination sample number is
temporarily being used to execute Time Stretch, and
therefore the Save operation cannot be executed.
• Change the save-destination sample number.
Destination sample data used in source sample
Can't overwrite
Meaning: Since the sample data at the destination
(save location) is also used by the source sample, it
cannot be overwritten.
• Without using Overwrite, specify a different
sample for the destination (save location).
Destination sample is empty
Meaning: The sample for editing is empty.
Destination song is empty
Meaning: The song that was specified as the copy
destination or bounce destination does not exist.
• Execute the Create New Song command in the
dialog box that appears when a new song is
selected before copying or bouncing.
Directory is not empty
Meaning: When deleting a directory, files or
directories exist within that directory.
• Press the OK button to delete all files and/or
directories within that directory.
216
Cleanup directory
Are you sure?
Disc full
Meaning: When executing command in the Media
mode Make Audio CD page, Write to CD there is
insufficient space remaining on the USB CD-R/RW for
the data to be written.
• Either write to other media, or remove unneeded
tracks.
Disk not formatted
Meaning: When you attempted to perform a high-
level format (quick format) of media, the media had
not been physically formatted yet. To solve this
problem:
• Execute the Media mode Utility menu command
Format to physically format the media (full format).
E (Error–Exceeded)
Error in formatting medium
Meaning: An error occurred while performing a
physical format (full format) or high-level format
(quick format) of the media. To solve this problem:
• Use other media.
Meaning: When executing the Media mode Utility
menu command Convert to ISO9660 Format, an error
occurred while rewriting the UDF area. To solve this
problem:
• Use other media.
Error in reading from medium
Meaning: An error occurred while reading data from
media. This error may also appear when data is being
written to media by a Save or Copy operation. To solve
this problem:
• Execute the reading operation once again. If the
same error occurs, it is possible that the data on the
media has been damaged.
Error in writing to medium
Meaning: A verification error occurred while writing
data to a medium. To solve this problem:
• It is possible that the media has been physically
damaged. Try another media. Avoid using the
media that produced the error.
• When using external USB media, execute the Media
mode Utility menu command Check Medium.
Exceeded 16 Programs - some data not loaded
Meaning: You exceeded 16 programs while
performing Advanced Conversion Load. When an
AKAI Program is loaded, it will be converted into
multiple programs and one combination according to
its structure. At this time, the maximum number of M3
programs resulting from this conversion is limited to
16, which is the maximum number of programs that
can be used in a combination. To solve this problem:
• Load the AKAI programs individually, and edit
them on the M3.
• Instead of using Advanced Conversion Load, load
the multisamples or samples, and edit them on the
M3.