Installing The Options And Replacing The Calendar - Korg m3 Operation Manual

Appendices
Installing the options and
replacing the calendar battery
Before you proceed, please read the preceding "Safety
cautions" and "Cautions when installing option boards
or memory." The sound module must be removed
from the keyboard assembly in order to perform these
procedures. For details on how to remove the sound
module, please see the "Keyboard assembly Manual."
You will need a Phillips (+) screwdriver and a
cushioned surface to protect the sliders and knobs
from damage. You can also use a stack of magazines
(or the equivalent). Place the magazines at the four
corners of the sound module to protect the sliders and
knobs from damage, and place the sound module face
down on them.
You must leave the AC power cable disconnected
until you've finished the entire installation
process.
Be careful not to cut your hand on any metal parts
of the sound module or option board.
L/MONO R 1 OUTPUT [ ] 2 3 4
1 2 [ INPUT ] LINE MIC LEVEL IN [ S/P DIF ] OUT PEDAL SWITCH DAMPER
MIX PLAY/MUTE (SOLO)
IFX 1 IFX 2 IFX 3 IFX 4 IFX 5 MFX 1 MFX 2 TFX
RESET
1 2 3 4 5 6 7 8
CONTROLS
VOLUME CONTROL
MIX VOLUMES
MAIN ASSIGN T1-8 VALUE
CUTOFF RESONANCEEG INTENSITYEG RELEASE USER 1 USER 2 USER 3 USER 4
T9-16
MIXER
INPUTS
REALTIME
CONTROL
EXTERNAL
TONE
ADJUST
1 2 3 4 5 6 7 8
KARMA
1/9 2/10 3/11 4/12 5/13 6/14 7/15 8/16
DRUM
MASTER
TRACK SCENES 1-4 5-8 PRESS [KARMA] VEL .
SENS
A
LINKED
MODULE VEL . PAD
ON/OFF ON/OFF LATCH CONTROL B 1/5 2/6 3/7 4/8 FIXED MODE
C
CHORD
D ASSIGN
Cover "B"
Installing the EXB-RADIAS
If you are installing the EXB-FW and EXB-
RADIAS at the same time, install the EXB-FW first.
1. Use your Phillips (+) screwdriver to remove the
two screws from cover "A," and remove cover "A"
from the sound module.
204
STANDBY
ON
MODE BANK SELECT
COMBI PROG SEQ I-A I-B I-C
SAMPLING GLOBAL MEDIA U-A U-B U-C
SAMPLING
X-Y MODE
7 8 9
HOLD
4 5 6
SEQUENCER
MOTION
1 2 3 COMPARE
PAGE
EXIT SELECT 0 ENTER LOCATE
1 2 3 4 5 6 7 8
View from below
Cover "A"
View from above
2. Make sure that the EXB-RADIAS is oriented
correctly, and use the five screws to fasten it to the
back of cover "A."
3. Connect the cable of the EXB-RADIAS to the
connector of the sound module as shown below.
Firmly push the cable all the way in so that it does
not contact anything other than the connector on
the circuit board.
~ACV
I-D I-E I-F I-G
U-D U-E U-F U-G
TEMPO
120
START/
REC STOP
40 300
PAUSE REW FF
REC/ START/ TAP
WRITE STOP TEMPO
M U S I C WO R K S TAT I O N / S A M P L E R
4. Attach cover "A" to the sound module.
5. Fasten cover "A" using the two screws you
removed in step 1.