Roland DP990F Implementation page 30

● 0206: Enhancer→Chorus
This effect connects an enhancer and a chorus in series.
No Parameter Value
1 Enhancer Sens 0-127
2 Enhancer Mix 0-127
3 Chorus Pre Delay 0-125
4 Chorus Rate Mode 0-1
5 Chorus Rate #1 1-127
6 Chorus Rate 0-21
7 Chorus Depth 0-127
8 Chorus Balance #2 0-100
9 Level 0-127
● 0207: Enhancer→Flanger
This effect connects an enhancer and a flanger in series.
No Parameter Value
1 Enhancer Sens 0-127
2 Enhancer Mix 0-127
3 Flanger Pre Delay 0-125
4 Flanger Rate Mode 0-1
5 Flanger Rate #1 1-127
6 Flanger Rate 0-21
7 Flanger Depth 0-127
8 Flanger Feedback 0-98
9 Flanger Balance #2 0-100
10 Level 0-127
● 0208: Enhancer→Delay
This effect connects an enhancer and a delay in series.
No Parameter Value
1 Enhancer Sens #1 0-127
2 Enhancer Mix 0-127
3 Delay Mode 0-1
4 Delay Time 0-127
5 Delay Time 0-21
6 Delay Feedback 49-89
Description
0-127 Sensitivity of the enhancer
Level of the overtones generated
0-127
by the enhancer
Adjusts the delay time from the
0.0-100.0 ms direct sound until the chorus
sound is heard.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
0.05-10.00 Hz Frequency of modulation (Hz)
note Frequency of modulation (note)
0-127 Depth of modulation
Adjusts the volume balance
between the sound that is sent
D100:0W -
through the chorus (W) and the
D0:100W
sound that is not sent through the
chorus (D).
0-127 Output Level
Description
0-127 Sensitivity of the enhancer
Level of the overtones generated
0-127
by the enhancer
Adjusts the delay time from when
0.0-100.0 ms the direct sound begins until the
flanger sound is heard.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
0.05-10.00 Hz Frequency of modulation (Hz)
note Frequency of modulation (note)
0-127 Depth of modulation
Adjusts the proportion of the
flanger sound that is fed back into
-98 - +98%
the effect. Negative (-) settings will
invert the phase.
Adjusts the volume balance
between the sound that is sent
D100:0W -
through the flanger (W) and the
D0:100W
sound that is not sent through the
flanger (D).
0-127 Output Level
Description
0-127 Sensitivity of the enhancer
Level of the overtones generated
0-127
by the enhancer
When this is set to "note," the
ms, note effect is synchronized with the
tempo.
Adjusts the delay time from the
0-2540 ms direct sound until the delay sound
is heard. (Hz)
Adjusts the delay time from the
note direct sound until the delay sound
is heard. (note)
Adjusts the proportion of the delay
0 - +80%
sound that is fed back into the
effect.
7 Delay HF Damp 0-17
8 Delay Balance #2 0-100
9 Level 0-127
● 0209: Chorus→Delay
This effect connects a chorus and a delay in series.
No Parameter Value
1 Chorus Pre Delay 0-125
2 Chorus Rate Mode 0-1
3 Chorus Rate 1-127
4 Chorus Rate 0-21
5 Chorus Depth 0-127
6 Chorus Balance #1 0-100
7 Delay Mode 0-1
8 Delay Time 0-127
9 Delay Time 0-21
10 Delay Feedback 49-89
11 Delay HF Damp 0-17
12 Delay Balance #2 0-100
13 Level 0-127
30
Adjusts the frequency above which
sound fed back to the effect will be
200-8000 Hz,
cut. If you do not want to cut the
Bypass
high frequencies, set this
parameter to Bypass.
Adjusts the volume balance
between the sound that is sent
D100:0W -
through the delay (W) and the
D0:100W
sound that is not sent through the
delay (D).
0-127 Output Level
Description
Adjusts the delay time from the
0.0-100.0 ms direct sound until the chorus
sound is heard.
When this is set to "note," the
Hz, note effect is synchronized with the
tempo.
0.05-10.00 Hz Frequency of modulation (Hz)
note Frequency of modulation (note)
0-127 Depth of modulation
Volume balance between the direct
D100:0W -
sound (D) and the chorus sound
D0:100W
(W)
When this is set to "note," the
ms, note effect is synchronized with the
tempo.
Adjusts the delay time from the
1-2540 ms direct sound until the delay sound
is heard. (Hz)
Adjusts the delay time from the
note direct sound until the delay sound
is heard. (note)
Adjusts the proportion of the delay
0 - +80% sound that is fed back into the
effect.
Adjusts the frequency above which
sound fed back to the effect will be
200-8000 Hz,
cut. If you do not want to cut the
Bypass
high frequencies, set this
parameter to Bypass.
Adjusts the volume balance
between the sound that is sent
D100:0W -
through the delay (W) and the
D0:100W
sound that is not sent through the
delay (D).
0-127 Output Level