Program Change; Pitch Bend Change - Roland V-Piano Grand GP-7 Implementation

MIDI Implementation
❍Resonance (Controller number 71) †
Status 2nd byte
BnH 47H
n = MIDI channel number:
vv= Resonance value (relative change):
❍Release Time (Controller number 72) †
Status 2nd byte
BnH 48H
n = MIDI channel number:
vv = Release Time value (relative change): 00H - 7FH (-64 - 0 - +63)
❍Attack time (Controller number 73) †
Status 2nd byte
BnH 49H
n = MIDI channel number:
vv = Attack time value (relative change): 00H - 7FH (-64 - 0 - +63),
❍Cutoff (Controller number 74) †
Status 2nd byte
BnH 4AH
n = MIDI channel number:
vv = Cutoff value (relative change):
❍Decay Time (Controller number 75) †
Status 2nd byte
BnH 4BH
n = MIDI channel number:
vv = Decay Time value (relative change): 00H - 7FH (-64 - 0 - +63)
❍Vibrato Rate (Controller number 76) †
Status 2nd byte
BnH 4CH
n = MIDI channel number:
vv = Vibrato Rate value (relative change): 00H - 7FH (-64 - 0 - +63)
❍Vibrato Depth (Controller number 77) †
Status 2nd byte
BnH 4DH
n = MIDI channel number:
vv = Vibrato Depth Value (relative change):00H - 7FH (-64 - 0 - +63)
❍Vibrato Delay (Controller number 78) †
Status 2nd byte
BnH 4EH
n = MIDI channel number:
vv = Vibrato Delay value (relative change):00H - 7FH (-64 - 0 - +63)
❍Portamento Control (Controller number 84) †
Status 2nd byte
BnH 54H
n = MIDI channel number:
kk = source note number:
* A Note-on received immediately after a Portamento Control message will change
continuously in pitch, starting from the pitch of the Source Note Number.
* If a voice is already sounding for a note number identical to the Source Note Number,
this voice will continue sounding (i.e., legato) and will, when the next Note-on is
received, smoothly change to the pitch of that Note-on.
* The rate of the pitch change caused by Portamento Control is determined by the
Portamento Time value.
2
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (-64 - 0 - +63)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
vvH
0H - FH (ch.1 - 16)
3rd byte
kkH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
❍Effect 1 (Reverb Send Level) (Controller number 91)
Status 2nd byte
BnH 5BH
n = MIDI channel number:
vv = Reverb Send Level:
❍Effect 3 (Chorus Send Level) (Controller number 93) †
Status 2nd byte
BnH 5DH
n = MIDI channel number:
vv = Chorus Send Level:
❍RPN MSB/LSB (Controller number 100, 101) †
Status 2nd byte
BnH 65H
BnH 64H
n = MIDI channel number:
mm = upper byte (MSB) of parameter number specified by RPN
ll = lower byte (LSB) of parameter number specified by RPN
<<< RPN >>>
Control Changes include RPN (Registered Parameter Numbers), which are extended.
When using RPNs, first RPN (Controller numbers 100 and 101; they can be sent in any
order) should be sent in order to select the parameter, then Data Entry (Controller numbers
6 and 38) should be sent to set the value. Once RPN messages are received, Data Entry
messages that is received at the same MIDI channel after that are recognized as changing
toward the value of the RPN messages. In order not to make any mistakes, transmitting
RPN Null is recommended after setting parameters you need.
This device receives the following RPNs.
RPN Data entry
MSB, LSB MSB, LSB Notes
00H, 00H mmH, llH Pitch Bend Sensitivity
mm: 00H - 18H (0 - 24 semitones)
ll: ignored (processed as 00H)
Up to 2 octave can be specified in semitone steps.
00H, 01H mmH, llH Channel Fine Tuning
mm, ll: 20 00H - 40 00H - 60 00H
(-4096 x 100 / 8192 - 0 - +4096 x 100 / 8192 cent)
00H, 02H mmH, llH Channel Coarse Tuning
mm: 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll: ignored (processed as 00H)
00H, 05H mmH, llH Modulation Depth Range
mm, ll: 00 00H - 06 00H ( 0 - 16384 x 600 / 16384 cent)
7FH, 7FH ---, --- RPN null
RPN and NRPN will be set as "unspecified." Once this
setting has been made, subsequent Parameter values that
were previously set will not change.
mm, ll: ignored
●Program Change
Status 2nd byte
CnH ppH
n = MIDI channel number:
pp = Program number:
●Pitch Bend Change
†
Status 2nd byte
EnH llH
n = MIDI channel number:
mm, ll = Pitch Bend value:
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
vvH
0H - FH (ch.1 - 16)
00H - 7FH (0 - 127)
3rd byte
mmH
llH
0H - FH (ch.1 - 16)
0H - FH (ch.1 - 16)
00H - 7FH (prog.1 - prog.128)
3rd byte
mmH
0H - FH (ch.1 - 16)
00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)