Roland GP-9 Leaflet

1
Leaflet For a Dealer or a Qualified Professional Installer
To assure that assembly is carried out properly, make sure to read these instructions before you begin the assembly.
¹ This leaflet is for a dealer or a qualified professional installer. The customer should not attempt to move
or assemble the instrument.
¹ Please consult your Roland dealer or a piano specialist to move or disassembling / assemble the piano.
Roland cannot warrant the safety of the assemble operation, if this operation is carried out by the
customer.
¹ Save this leaflet together with the Owner's Manual so that it will be available for reference by a piano specialist when disassembling or
moving the instrument.
¹ Make sure to keep screws and any other small parts in a safe location that is out of the reach of small children, so such small parts won't
accidentally get swallowed.
* Since this product is very heavy, you must make sure that a sufficient number of people are on hand to help, so you can lift and move it safely,
without causing strain. When assembling the unit, obtain the assistance of enough people that assembly can be performed safely and as
directed.
* Do not place the piano unit itself directly on the floor. Doing so will damage the jack enclosure, AC adaptor, and headphone hook that are
located on the bottom of the piano unit.
* Be careful not to pinch your hands or drop this unit on your foot during assembly or transport.
* The surface of the piano unit and the stand are very delicate; handle with care to avoid scratching them.
Parts Check
A
B
C
B
D
E
D
* The tools used for assembly are not included. You will need to separately provide a Philips screwdriver (no. 2) and
a box wrench (19 mm across flats, length 200 mm or less).
Do not use an electric screwdriver. Doing so might strip the bolt or damage the screw threads.
*5100078295-02*
© 2023 Roland Corporation
A
1
A Piano unit
B
2
B Legs: 3
C
Lyre assembly: 1
C 3
D
D Lyre support rods: 2
E 4
B
E Caster cups: 3
5
F
6
7
Assembly Procedure
Attach the Legs to the Piano
NOTE
The surface of the piano unit and the stand are very delicate; handle
with care to avoid scratching them.
1.
Position the legs
2.
Place a spring washer
order onto each hex bolt
tightening the bolts, use the box wrench to secure the
legs to the piano unit (two locations).
B
* Do not tighten hex bolts
spring washer
B
3.
Fasten the two other legs
same fashion.
Plain washers: 8
Attach the Lyre Assembly
Spring washers: 8
1.
Place a spring washer
Hex bolts: 8
order onto each hex bolt
fasten the lyre assembly
Screws (4 x 20 mm): 4 bolts (two locations).
* Do not tighten hex bolts
spring washer
Screws (4 x 16 mm): 2
Headphone hook: 1
Cord clamps: 3
200 mm or less
Box wrench
C
19 mm across flats
A
B
C
2.
Use two screws
* Be careful not to use screws
D
Screws
E
in place beneath the piano unit.
B
F
and a plain washer in that
2 1
. After provisionally hand-
3
4
excessively. Stop tightening when the
3
2 becomes flat.
3.
Attach the lyre support rods
and the screws that are attached to the pedal unit
1
(four screws total).
Tighten as much as
2
you can by hand,
3 and then use a box
wrench to firmly
tighten.
to the piano unit in the
B
and a plain washer in that
1
2
. Use the box wrench to
3
to the piano unit with the Placing the Casters on the Caster Cups
C
excessively. Stop tightening when the
3 NOTE
2 becomes flat.
Make sure that the casters are placed on top of the caster cups. As the
caster cups stabilize the piano and prevent it from moving when you
are playing or when force is applied to the piano, you must use these
caster cups to prevent serious risk.
1.
Place the casters on the caster cups
(three locations).
* Be careful not to pinch your hands or drop this unit on your foot.
2.
Position the casters and the metal parts that support
the casters in the directions shown in the illustration
below.
1
Tighten as much as you
can by hand, and
2
then use a box
3
wrench to firmly
tighten.
Direction of the
metal parts that
support the
casters
1
to fasten the lyre assembly .
4
C
5 by mistake.
4 (4 x 20 mm)
by using screws
4
D
Take care that the
4
support rod is in
the correct vertical
D orientation.
Use the two screws that are
attached to the pedal unit.
E
Direction of casters