Table of Contents
Advertisement
Quick Links
I N S T A L L A T I O N I N S T R U C T I O N S
Instrucciones de instalación
Installationsanleitung
Instruções de Instalação
Dual Stud Short Throw Wall Mounts
Istruzioni di installazione
Installatie-instructies
Instructions d´installation
Spanish Product Description
German Product Description
Portuguese Product Description
Italian Product Description
Dutch Product Description
French Product Description
SP-WALLKIT-02
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for InFocus SP-WALLKIT-02
Summary of Contents for InFocus SP-WALLKIT-02
- Page 1 I N S T A L L A T I O N I N S T R U C T I O N S Instrucciones de instalación Istruzioni di installazione Installationsanleitung Installatie-instructies Instruções de Instalação Instructions d´installation Dual Stud Short Throw Wall Mounts Spanish Product Description German Product Description Portuguese Product Description Italian Product Description Dutch Product Description French Product Description SP-WALLKIT-02...
-
Page 2: Important Warnings And Cautions
InFocus makes no representation of warranty, expressed or implied, regarding the information contained herein. InFocus assumes no... - Page 3 Hex-Head Wrench Security Wrench Llave de cabeza hexagonal Llave de seguridad Sechskantschlüssel Sicherheitsschlüssel Chave de cabeça sextavada Chave de segurança Chiave esagonale Chiave di sicurezza Zeskantsleutel Veiligheidssleutel Clé à tête hexagonale Clé de sécurité Visit the InFocus support site at www.infocus.com/support...
-
Page 4: Tools Required For Installation
5/16" (security) AA (3) Z (3) W (1) V (10) U (4) M4 x 12mm X (1) 5/32" Y (1) 1/4-20 x 3/4" #8-32 x 1/2" [interface bracket] (security) (security) (security) [projector mount] Visit the InFocus support site at www.infocus.com/support... -
Page 5: Site Requirements
Steel Stud (2 x 4 / 25ga minimum) Stud type and structural strength must conform to the North American Specification for the Design of Cold-Formed Steel Structural Members. [362, 125 18, C-Shape, S - Stud Section] Visit the InFocus support site at www.infocus.com/support... -
Page 6: Assembly And Installation
Assembly and Installation Wood Studs Determine mounting location on wall. Use a stud finder to The SP-WALLKIT-02 short throw projector mounts can be locate studs. For studs less than 16" apart, mounting mounted to concrete, concrete block, wood studs or steel studs. -
Page 7: Side View
(See Figure 7) Slide plastic cap on anchor (P) towards wall until flange of cap is flush with wall. (See Figure 7) Visit the InFocus support site at www.infocus.com/support... -
Page 8: Installation To Wall Bracket
Turn clockwise to raise mounting level or turn (See Figure 11) counterclockwise to lower mounting level. (See Figure 13) Tighten two bolts on either side of pitch adjustment screw. (See Figure 13) Visit the InFocus support site at www.infocus.com/support... -
Page 9: Projector Mount Installation
IMPORTANT ! : If projector mount is NOT installed in the same direction as shown in Figure 16, ROLL adjustment screws will be inaccessible! Figure 14 mounting plate roll adjustment screws (J) x 4 Figure 16 Visit the InFocus support site at www.infocus.com/support... - Page 10 Verify mounting screws are properly seated in mounting slots in mount base. (See Figure 19) Secure interface bracket (X) to top of InFocus projector using three M4x12mm Phillips pan machine screws (Z) and Move locking lever to "locked" position. (See Figure 19) three M4 washers (AA).
-
Page 11: Pitch Adjustment
• Routing Cables from Below (Steps 4 and 5) Open cable clips along bottom edge of wall bracket cross bracket (See Figure 25) Figure 22 Visit the InFocus support site at www.infocus.com/support... - Page 12 Thread cable up wall bracket channel and into opened cable clips. (See Figure 26) Proceed to Step 7. cables cables (example) (view from back) Figure 26 Figure 27 (bottom view) cable (example) projector Figure 28 Visit the InFocus support site at www.infocus.com/support...
- Page 13 (See Figure 30) Figure 32 Figure 30 10. Slide outer cover of mount (A) back against mounting bracket. (See Figure 31) Visit the InFocus support site at www.infocus.com/support...
-
Page 14: Installation Of Wall Bracket Covers
(F) x 2 projector arm not shown for display purposes (F) x 4 Figure 34 Figure 36 Slide outer cover of mount (A) away from mounting bracket to expose pitch adjustment screw. (See Figure 37) Visit the InFocus support site at www.infocus.com/support... - Page 15 (See Figure 39) Tighten two bolts on either side of pitch adjustment screw. (See Figure 39) Tighten two 1/4-20 x 5/8" screws (E) on underside of mounting bracket. (See Figure 39) Visit the InFocus support site at www.infocus.com/support...
-
Page 16: Lateral Shift Adjustment
(See Figure 42) (bottom view) (F) x 2 (E) x 2 Figure 44 Figure 42 Slide outer cover of mount (A) away from mounting bracket. (See Figure 43) Visit the InFocus support site at www.infocus.com/support... -
Page 17: Security Screw Installation (Optional)
Remove two #8-32 x 1/2" Phillips pan machine screws (F) holding mount cover on projector arm. (See Figure 47) Install two #8-32 x 1/2" button head security screws (V) into Figure 48 holes on mount cover. (See Figure 47) Visit the InFocus support site at www.infocus.com/support... - Page 18 Remove one of four bolts from adapter plate. (See Figure adapter plate plastic spacer (U) x 4 (one at a time) Figure 51 11. Reinstall projector to mount. Refer to Projector Installation Section for details. Visit the InFocus support site at www.infocus.com/support...
- Page 19 Installation Instructions SP-WALLKIT-02 Visit the InFocus support site at www.infocus.com/support...
- Page 20 SP-WALLKIT-02 Installation Instructions InFocus Corporation 13190 SW 68th Parkway, Ste 200 Portland, OR 97223 8802-002043 Rev00 2010 InFocus Corporation www.infocus.com 09/10...
Need help?
Do you have a question about the SP-WALLKIT-02 and is the answer not in the manual?
Questions and answers