Haier Tiana HW1007NZP User Manual page 9

13 Other Functions
Power-down memory
With the power-down memory function, the washer-dryer can memorize the program's running state
in case of power failure or loose plug during washing and continue the selected program after resuming
the power supply and turning on the washer-dryer by pressing the "On" button.
Cancel or reselect a program in the process of running
If the child lock function is activated, please deactivate it before performing the following operations.
If there is a need to reset the mode (including the "Wash", "Wash & Dry" and "Dry" modes) and washing
program (e.g. cotton, Synthetics...), gently press and hold the "Off" button for 3s to shut down the
washer-dryer, turn on the washer-dryer again by pressing the "On" button, then reset the desired mode,
washing program and washing parameters.
If only washing parameters (including washing time, times of rinsing, spinning time and spinning speed)
need to be reset, gently press the "Start/Pause" button, then press the "Wash", "Rinse", "Spin" and
"Speed" buttons respectively to set washing parameters, then gently press the "Start/Pause" button
again to start the selected program.
Eccentric protection
When spinning, if the clothes are not evenly distributed, the washer-dryer will fluff out and redistribute the
clothes and continue spinning after the clothes distribution becomes even. If the clothes distribution does not
become even within the specified time, the washer-dryer will not spin to avoid abnormal vibration. In this case,
please check the clothes for intertwist and rearrange them, then select the "spin" program to spin the clothes.
When there are few articles, the washer-dryer may not spin due to eccentric protection. In this case, you can
put more articles in the washer-dryer and make them evenly distributed, then continue spinning. In addition, it
is normal that the program time will prolong for the washer-dryer rearranges and fluffs out the clothes.
Drying
With the function of drying ramie cotton and chemical fiber fabrics, the washer-dryer can automatically
determine the degree of dryness and end the drying program in time. Pay attention to the following when
drying:
Whether the clothes suitable for drying depends on their texture. Make sure that the clothes are suitable
for drying with washing machine before drying.
Before drying, make sure that the water tap is turned on and the water must be cold.
As for the spun clothes, take and fluff them out, and then put them in the drum for drying.
If too many clothes are dried at a time, not only the drying effect is not ideal but also the clothes are
liable to wrinkle. The drying time may be longer than the pre-set time.
The drying time may be shorter than the pre-set time when drying few clothes or light clothes.
It is normal that the drying time may be longer when selecting low-temperature drying program.
Automatic weighing function
In the "Wash" and "Wash/Dry" modes, the "Cotton", "Memory", "Synthetics", "High-Temp" and "Night
Wash" programs all have automatic weighing function.
After setting a program, press the "Start/Pause" button, the drum will start rotating and detecting the
clothes weight. Overweight may be detected in case of wet clothes. In addition, it is normal that low impact
sound may be heard from the washer-dryer.
17
(3) Install the water inlet pipe joint
Loosen the nut to the extent that approximate 3-4 turns of
screw thread are exposed;
Loosen four screws of the water inlet pipe joint to the extent
that the joint can be ringed onto the water tap;
If the water inlet pipe joint cannot be ringed onto the water
tap, please remove the bushing and install again;
Turn the screw against the wall to an approximately proper
position in advance, ring the water inlet pipe joint onto the water
tap, then evenly tighten the remaining three screws in place,
and finally tighten the nut.
(4) Connect the water inlet pipe
Press down the slider and insert the water pipe into the water inlet
pipe joint;
Hook the water inlet pipe joint with the locking lever, then loosen the
slider until a "poop" is heard. locking lever
(5) Connect to the washer-dryer
Ring the nut at the other end of water inlet pipe onto the water inlet
valve joint;
Tighten and confirm the nut of water inlet pipe in place.
(6) Check the water inlet pipe for good connection
Check for firm connection;
After installation, turn on the water tap and check for water leakage;
Before every use of the washer-dryer, please check for firm
connection between the water inlet pipe and the water tap;
Never forcibly bend the water inlet pipe.
Wall
If the water tap is placed
against the wall, you may
turn this screw to a proper
positio in advance
Bushing
3-4 turns
Tally
Nut
locking lever
6