Safety Precautions 1 - Haier Tiana HW1007NZP User Manual

1 Safety Precautions
Electrical safety prompt:
Please pay attention to electrical safety during use.
The plug should be accessible after the washer-dryer is installed in place. Do
not disconnect the plug from the socket by pulling the power cord. If the
power cord needs to be replaced, ask a qualified technician or contact our
After-sales Service Department for replacement. Prevent the power cord
from being pressed by any foot and from such problems as break-off, flattening, etc.
Power supply must use an independent socket, the grounding terminal of which must be
properly grounded. The socket must be a qualified product.
Such overload protective devices as proper fuse must be available at the user's home.
And, the ammeter, wire and socket must be able to withstand 10A current.
Warning sign:
The contents with this sign involve the safety of both the product and the user.
Be sure to strictly follow these instructions, otherwise the washer-dryer
may be damaged or the user may be injured.
Keep the washer-dryer away from any heat source and direct sunlight to prevent the aging of
plastic and rubber parts.
Prohibitory sign:
The contents with this sign indicate the behaviors to be absolutely
prohibited. Failure to follow these instructions may result in damage to the
washer-dryer or personal injury.
Do not use such chemicals as flammable detergent and dry-cleaning solvent to wash the clothes. Do
not use any flammable spray near the washer-dryer. In case of flammable gas leakage, do not plug or
unplug the washer-dryer's power plug.
The washer-dryer's door and tabletop panel are relatively hot during heating and drying. For
the purpose of safety, keep the children away from the washer-dryer. In addition, when
draining hot water, be careful to avoid scald.
After unpacking the washer-dryer, do not allow the children to play with the disassembled
packaging materials such as carton, plastic packaging bag and foam, etc.
Do not install the washer-dryer outdoors and in excessively humid environment, otherwise moisture on
the electrical components may easily cause damage to the ignition system or other accidents. In case of
inadvertent water spray onto or into the washer-dryer, only after the washer-dryer is thoroughly dried
can you use it.
Neither should you place the washer-dryer directly onto an airproof carpet in order not to block the
bottom vent, nor place it close up to the wall or furniture to avoid accidents. Do not use the
washer-dryer on any platform above the floor, otherwise it may fall off onto the floor and be damaged.
1
State Phenomenon
Poor washing effect
When
Forceless washing
wash
Stop operation during washing
When
Repeated rinsing
rinse
No spinning
When
Loud noise when spinning
spin
Vibration and displacement
The clothes are not spun dry agter
finishing the spinning progran
When
No water discharge or slow water
discharge
drain
The control panel is partially hot
Others
The washing does not end after the
preset delay time
Solution
Check the detergent for proper type and dosage
Check whether a proper program is selected
Check whether the clothes weight exceeds the washer-dryer's
rated washing capacity
Check whether sudden power failure or power supply cut-off
occurs
Check whether the "Srart/Pause" button is pressed
The washer-dryer with the function of automatic shutdown upon
clean detected automatically increases or decreases the times
of rinsing (1-2 times) according to the degree of dirtiness of the
clothes
The washer-dryer's program is set with discharge time and the
spinning starts after a period of time
Check whether the clothes intertwist
Check whether all the packaging bolts are removed
Check whether the washer-dryer is level (The feet can be
adjusted to level the washer)
Check whether the clothes intertwist
Check whether the washer-dryer collides with other objects
Check whether there are forergn bodies in the washer-dryer
The spinning effect varies with type of clothes
Check whether eccentric protection functions due to few clothes
Check whether thedrain pipe is bent, clogged or frozen
Check whether the outlet of drain pipe is 10cm above the floor
Check whether the filter is clogged
It is normal that electronic components are a bit hot
Poor water feeding/drainage conditions or unbalanced clothes
distribution results in longer time
22