To Cancel An Automatic Timer Recording - Zenith TVSC2040F Operating Manual & Warranty

TO CORRECT A PROGRAM
• While setting a program; press the nEW
button to go back one step and enter the correct
numbers using the PLAY or STOP button.
• After setting a program;
1) Press the PWR(POWER) button.
2) Repeat steps [1] - [2] on page 27.
3) Press the F.FWD button (or press the nEW
button to go back one step) until the part you
want to correct begins flashing, then make the
changes pressing the PLAY or STOP button.
4) Press the PWR(POWER) button to set
automatic timer recording.
TO CANCEL AN AUTOMATIC TIMER
RECORDING
• After setting a program;
1) Press the PWR(POWER) button.
2) Repeat steps [1] ~ [2] on page 27 and select a
programyou want to cancel.
3) Press the T-PROG. CLEAR button.
4) Press the MENU buttonon the remote control
to return to TV mode.
• While recording is in progress;
1) Press the PWR(POWER) button.
2) Press the STOP/EJECT button on the TV/VCR.
TO CHECK THE BEGIN/END TIME
1) Press the PWR(POWER) button so that the
REC indicator goes off.
2) Press the MENU button on the remote control.
3) Confirm "TIMER PROGRAMMING" is pointed
to.
4) Press the F.FWD button. The details of
programs appear on the TV screen.
5) Press the MENU button on the remote control
to return to TV mode.
AUTO TIMER RECORDING REMINDERS:
• Make sure the channel you want to record is
pmporly set in advance.
• It is not necessary to press the REC(ORD)
button for timer recording.
• Recording begins automatically at the Start
time.
• If you are recording using a T_mer mode, you
cannot operate the unit manually.
• The erase-prevention tab on the cassette must
be in place (or you must put tape over the hole).
• If the erase-prevention tab is removed, the
cassette will be ejected when the
PWR(POWER) button is pressed to off.
• If the tape runs out before the end time, the
TVNCR will switch to the Stop mode
immediately, and the tape will be ejected.
With this function, after timer recording is finished,
the tape will automatically rewind to the start of
the recorded program(s).
1
Select "USER'S SET UP"
Press the MENU button on
the remote control.
Press the PLAY or STOP
button to point to "USER'S
SET UP".
Then, press the F.FWD
button.
MENU-
T_MER pROGRAMMqNG
PICTURE CONTROL
SETFING CLOCK
CP_NNEL SET UP
_. USER'S SET UP
V_HIP SET UP
L&NGUAG E ENGLISH I
CAPTION [OFF]
ZERO RETURN
_IME SEARCH
INDEX SEARCH
2
Set "AUTO RETURN" to [ON]
Press the PLAY or STOP
button to point to "AUTO
RETURN".
Press the F.FWD or REW
button until [ON] appears.
_ USE R'S SET Up /
J
RENTAL OF
REP'EAT pLAy ,}O=_
,-*_O,E,UR. p_,_
3
Auto Return will begin
When all the timer recordings are completed, the
TVNCR will rewind to the beginning of the
recorded program(s).
NOTE:
= If you press the PWR(POWER) button while
tape is rewinding, the Auto Return will stop.
4
Watch the recorded program
Press the PLAY button.
TO CANCEL THE AUTO RETURN MODE
Repeat steps [1] and [2], select [OFF] using the
F.FWD or REW button.
If there is a power failure of any kind, the unit
will retain its memory for this feature,
- 29 - EN
9K16