Poulan Pro PP125 Instruction Manual page 3

• Keep others away when making carburetor
adjustments.
• UseonIy recommended Poulan PRO
accessories and r eplacement parts,
• Have a ll maintenance andservice not
explained inthis manual performed byan
authorized service deaIer.
FUEL SAFETY
• Mix and pour fuel outdoors,
• Keep away from sparks or flames.
• Use a container approved for fuel,
• Do not smoke or allow smoking near fuel or
the unit,
• Avoid spilling fuel or oil Wipe up all fuel spills.
• Move at least 10 feet (3 meters) away from
fueling site before starting engine,
• Stop engine and allow to cool before
removing fuel cap.
• Always store gasoline in a container
approved for flammable liquids.
TRANSPORTING AND STORAGE
• Allow engine to cool; secure unit before
storing or transporting in vehicle.
• Empty the fuel tank before storing or
transporting the unit. Use up fuel left in the
carburetor by starting the engine and letting it
run until it stops.
• Store unit and fuel in area where fuel vapors
cannot reach sparks or open flames from
water heaters, electric motors or switches,
furnaces, etc.
• Store unit so line limiter blade cannot
accidentally cause injury. The unit can be
hung by the shaft,
• Store unit out of reach of children,
SAFETY NOTICE: Exposure to vibrations
through prolonged use of gasoline powered
hand tools could cause blood vessel or nerve
damage in the fingers, hands, and joints of
people prone to circulation disorders or abnor-
mal swellings. Prolonged use in cold weather
has been linked to blood vessel damage in
otherwise healthy people, if symptoms occur
such as numbness, pain, loss of strength,
change in skin color or texture, or loss of feeling
in the fingers, hands, or joints, discontinue the
use of this tool and seek medical attention. An
anti-vibration system does not guarantee the
avoidance of these problems. Users who oper-
ate power tools on a continual and regular basis
must monitor closely their physical condition
and the condition of this tool,
SPECIAL NOTICE: This unit is equipped
with a temperature limiting muffler and spark
arresting screen which meets the require-
ments of California Codes 4442 and 4443. All
U.S. forest land and the states of California,
Idaho, Maine, Minnesota, New Jersey, Ore-
gon, and Washington require by law that
many internal combustion engines be
equipped with a spark arresting screen. Ifyou
operate in a locale where such regulations ex-
ist, you are legally responsible for maintaining
the operating condition of these parts. Failure
to do so is a violation of the law. For normal
homeowner use, the muffler and spark arrest-
ing screen will not require any service. After
50 hours of use, we recommend that your
muffler be serviced or replaced by your autho-
rized service dealer.
LINE TRIMMER SAFETY
'_ WARNING: Inspectthe areabefore
each use. Remove objects (rocks, broken
glass, nails, wire, etc.) which can be thrown
by or become entangled in line. Hard objects
can damage the trimmer head and be thrown
causing serious injury.
• Use oniy for trimming, scalping, mowing
and sweeping, Do not use for edging,
pruning or hedge trimming,
• Cut from your left to your right, Cutting on
right side of the shield will throw debris
away from the operator,
ADDITIONAL SAFETY RULES
FOR OPTIONAL ATTACHMENTS
_'WARNING: For each optional at-
tachment used, read entire instruction manu-
al before use and follow all warnings and in-
structions in manual and on attachment.
AO&WARNING:
Ensure handlebar is
installed when using edger or brushcutter at-
tachments. Attach handlebar above arrow on
safety label on the upper shaft (engine end of
unit). If your edger or brushcutter attachment
does not include a handlebar, a handlebar ac-
cessory kit (#530071451) is available from
your authorized service dealer.
Handlebar
EDGER SAFETY
AO&WARNING: inspect the area to be
edged before each use. Remove objects
(rocks, broken glass, nails, wire, etc.) which
can be thrown by the blade or can wrap
around the shaft.
• Blade rotates momentarily after the trigger
is released. The blade can seriously cut
you or others,
• Allow blade to stop before removing it from
the cut,
Blade rotates before removing it I
Allow blade to stop
after the from the cut. J
td_lger is _/
release_
• Throw away blades that are bent, warped,
cracked, broken or damaged in any other
way, Replace parts that are cracked,
chipped, or damaged before using the unit,
• Do not attempt to remove cut material nor
hold material to be cut when the engine is
running or when cutting blade is moving,