Poulan Pro PP125 Instruction Manual page 10

_=WARNING:
Make sure the locking/
release button is looked in the primary hole
and the knob is securely tightened before op-
erating the unit. All attachments are designed
to be used in the primary hole unless otherwise
stated in the applicable attachment instruction
manual. Using the wrong hole could lead to seri-
ous injury or damage to the unit.
Secondary Hole
Locking/Release
Button in Primary Hole
OPERATING INSTRUCTIONS
It is recommended that the engine not be
operated for longer than 1 minute at full
throttle.
OPERATING POSITION
ALWAYS WEAR:
Hearing
Protection
e Protection
Lone
Heavy shoes
-.4
Out only from your left to your riaht, _
i_ WAR NIN G: Always wear eye protec-
tion. Never lean ever the trimmer head,
Rocks or debris can ricochet or be thrown into
eyes and face and cause blindness or other
serious injury.
When operating unit, stand as shown and
check for the following:
• Wear eye protection and heavy clothing.
• Hold trigger handle with your right hand and
assit handle with left hand.
• Keep unit below waist level.
• Out only from your left to your right to
ensure debris is thrown away from you.
Without bending over, keep line near and
parallel to the ground and not crowded into
material being cut.
Do not run the engine at a higher speed than
necessary. The cutting line will cut efficiently
when the engine is run at less than full throttle.
At lower speeds, there is less engine noise and
vibration. The cutting line will last longer and will
be less likely to %reid" onto the spool.
Always release the throttle trigger and allow
the engine to return to idle speed when not
cutting.
To stop engine:
• Release the throttle trigger.
• Move the ON/OFF switch to the OFF posi-
tion.
TRIMMER LINE ADVANCE
Thetrimmer line will advance approximately 2
inches (5 cm) each time the bottom of the
trimmer head is tapped on the ground with the
engine running at full throttle.
The most efficient line length is the maximum
length allowed by the line Iimiter. Always keep
the shield in place when the tool is being oper-
ated.
To advance line:
• Operate the engine at full throttle.
• Hotd the trimmer head parallel to and above
the grassy area.
• Tap the bottom of the trimmer head lightly on
the ground one time. Approximately 2 inches
(5 cm) of line will be advanced with each tap.
Always tap the trimmer head on a grassy area.
Tapping on surfaces such as concrete or as-
phalt can cause excessive wear to the trimmer
head.If the line is worn down to 2 inches (5 cm)
or less, more than one tap will be required to ob-
tain the most efficient line length.
_;;llLWARNING:
use only 0.095" (2.4
mm) diameter line, Other sizes of line will not
advance properly and can cause serious
injury. Do not use other materials such as
wire, string, rope, etc, Wire can break off dur-
ing cutting and become a dangerous missile
that can cause serious injury,
CUTTING METHODS
_,WARNING: use
minimum
speed
and do not crowd the line when cutting around
hard objects (rock, gravel, fence posts, ete,),
which can damage the trimmer head, become
entangled in the line, or be thrown causing a
serious hazard.
• The tip of the line does the cutting. You will
achieve the best performance and mini-
mum line wear by not crowding the line into
the cutting area, The right and wrong ways
are shown below.
Tip of the line Line crowded into
does the cutting, work area,
Right Wrong
• The line will easily remove grass and
weeds from around wails, fences, trees and
flower beds. but it also can cut the tender
bark of trees or shrubs and scar fences.
• For trimming or scalping, use less than full
throttle to increase line life and decrease
head wear, especially:
10