Related Manuals for Fisher & Paykel CG755
Summary of Contents for Fisher & Paykel CG755
-
Page 1: Installation Instructions
Installation instructions User guide Gas-on-glass cooktops CG604 and CG755 models GB IE... -
Page 3: Table Of Contents
Contents Safety and warnings Installation instructions Introduction Using your cooktop Care and cleaning Troubleshooting Warranty and service Important! SAVE THESE INSTRUCTIONS The models shown in this manual may not be available in all markets and are subject to change at any time. For current details about model and specification availability in your country, please visit our local website listed on the back cover or contact your local Fisher &... -
Page 4: Safety And Warnings
Always disconnect the cooktop from mains power supply before carrying out any maintenance operations or repairs. In the room where the cooktop is installed, there must be enough air to allow the gas to burn correctly, according to the current local regulations. - Page 5 Safety and warnings Particular attention shall be given to the relevant requirements regarding ventilation. This product should not be sealed into the bench with silicone or glue. Doing so will make future servicing difficult. Fisher & Paykel will not be liable for costs associated with releasing such a product, nor for repairing damage that may be incurred in doing this.
- Page 6 Do not touch the cooktop components, burners, trivets/pan supports or the base when hot. Before cleaning, turn the burners off and make sure the whole cooktop is cool. Failure to follow this advice may result in serious injury. Explosion Hazard Do not store fl ammable materials such as gasoline near the cooktop.Do not...
- Page 7 Do not use an asbestos mat or decorative covers between the flame and the saucepan as this may cause serious damage to your cooktop. Do not place aluminium foil or plastic dishes on the cooktop burners. Do not let large saucepans or frying pans overlap the bench as this can deflect heat onto your benchtop and damage the surface.
-
Page 8: Installation Instructions
(below top of bench) width of chassis depth of chassis overall width of cutout overall depth of cutout Gas connection is CG755: Electrical connection made at the right rear is made at the left rear (mm) CG604: Electrical connection is made... - Page 9 (eg thermal protection barrier) minimum clearance from benchtop to: overhead cabinet not directly above the cooktop Installation instructions...
- Page 10 The thermal protection barrier must be: removable heat-resistant made from low thermal conductivity material at least 30 mm below the base of the cooktop Fig. 1 Location of thermal protection barrier C above room temperature. Clearance Thermal protection...
- Page 11 100 cm The vents must be positioned close to the floor, preferably on the opposite side to the gas burners of your cooktop (as shown in Figs. 2a and 2b). The vents must be designed in such a way that they cannot be obstructed either from the inside or the outside.
- Page 12 Installation instructions Ventilation requirements (United Kingdom only) The appliance should be installed in a room or space with an air supply in accordance with BS 5440:2 2000. For rooms with a volume of less than 5 m , permanent ventilation through a free area of at least 100 cm will be required.
- Page 13 Turn the cooktop upside down and place it on a soft surface. Spread the seal around the edges, with the adhesive side facing down. Mount the supplied front and rear clamps (F and R) and screws (S) onto the cooktop, as shown (without tightening the screws).
- Page 14 Installation instructions Gas installation requirements This appliance is adjusted at the factory for use on Natural gas. To use it on LPG, it will first have to be converted. If the LPG conversion kit is not supplied with the appliance, contact your nearest Authorised Service Centre. Installation and service regulations (United Kingdom only) Important! This appliance must be installed and serviced only by a suitably qualified and registered person, and in...
- Page 15 If using a flexible hose, make sure it does not come into contact with moving parts. To maintain the minimum 30 mm clearance requirement below the base of the cooktop, the rear of the chassis is recessed to provide a channel for the appliance inlet pipe.
- Page 16 Use a single flexible hose only; never connect the cooktop with more than one flexible hose the flexible hose can easily be inspected along its entire length to check its condition; if it has an...
- Page 17 Leak-testing and flame-testing the cooktop After connecting the gas supply, check the piping and connections for leaks as required by local regulations. The presence of bubbles indicates a leak. Tighten or replace connections as appropriate, then re-check for leaks. Important! Do not use any naked flame to check for leaks.
- Page 18 Installation instructions...
- Page 19 Converting the cooktop to a different gas type Important! Only a suitably qualified and registered person may convert the cooktop to a different gas type. To convert from one gas type to another, you need to replace the injectors, and then adjust the minimum gas rate setting.
-
Page 20: Electrical Connection
Installation instructions Electrical connection Important! This appliance must be earthed. Installation must be carried out according to the manufacturer’s instructions. Incorrect installation may cause harm and damage to people, animals or property, for which the manufacturer accepts no responsibility. If the installation requires alterations to the domestic wiring system, call a qualified electrician. The electrician should also check that the socket cable section is suitable for the power drawn by the appliance. - Page 21 Installation instructions For the United Kingdom and the Republic of Ireland only: The appliance must be connected to a 220-240V~50 Hz supply by means of a suitably earthed three-pin socket and should be protected by a 3A fuse in the plug. If the appliance is supplied without a plug, fit a rewireable 13A three-pin plug fitted with a 3A fuse.
- Page 22 Have you clamped the cooktop to the bench securely? Have you used the supplied washers? Have you leak-tested all connections? Is the cooktop set for the correct gas type and pressure? Are the injector sizes correct for the gas type? Is the cooktop earthed? Check that the power supply cable is NOT touching the cooktop.
-
Page 24: Introduction
About your new cooktop Thank you for buying a Fisher & Paykel gas cooktop. Once it is installed and ready to use, you will want to know everything about it to make sure you get excellent results right from the start. - Page 25 The flame failure probe cuts off the gas supply to the burner if the flame is blown out. If the flames are accidentally extinguished, turn off the burner and do not try to light it again for at least one minute (to allow the gas to disperse). Using your cooktop OFF (closed valve) Minimum Fig.13 Burner knob...
- Page 26 Using your cooktop If a burner does not light Check that: the cooktop is plugged in and the electricity is switched on the gas is turned on the gas bottle is not empty (if you are using bottled gas) you have held down the knob for at least 10 seconds the ignitors are sparking.
-
Page 27: Using Your Cooktop
Use flat-bottomed pans, and make sure they match the size of the burner, as shown in the following table. A small pot on a large burner is not efficient. Diameters of pans which may be used on the cooktop Burners... - Page 28 Fig. 19 Never unscrew the burner plate fixing screws General advice Clean the cooktop after every use – do not allow stains to become burnt on. See the cleaning chart following. Clean the burners and ignitors at least once a month. See the cleaning chart following.
-
Page 29: Care And Cleaning
3 Apply ceramic glass Take extreme care when cooktop cleaner. working around hot surfaces! 4 Wipe with a clean, Heavy-duty scourers, some damp cloth and dry. nylon scourers and harsh/ abrasive cleaning agents may scratch the glass. - Page 30 Care and cleaning Replacing the auxiliary, semi-rapid, and rapid burners and pan supports Ensure that the burner and pan support assembly is: unable to rotate stable and level correctly aligned. Pan support Use the correct pan support only Flame spreader Ignitor Flame failure probe...
- Page 31 Replacing the triple-ring wok burner and pan support (five-burner models only) Ensure that the burner and pan support assembly is: unable to rotate stable and level correctly aligned. Flame spreader Ring Fig. 21 Ensure the burner and pan support are replaced correctly Care and cleaning Ignitor Use the correct...
-
Page 32: Troubleshooting
The gas pressure may not be at the correct level. Check with your service person or installer. Your cooktop may not be set up for the gas you are using. Check this with your service person or installer. Check the burner parts are clean and dry. Check the burner is assembled correctly and make sure the burner cap is sitting flat. -
Page 33: Warranty And Service
This cooktop has been designed and constructed in accordance with the following codes and specifications: Safety requirements of EEC Directive “Gas” 90/396... - Page 36 You should therefore check with your Dealer to ensure this booklet correctly describes the product currently available. www.fisherpaykel.co.uk www.fisherpaykel.ie GB IE Gas-on-glass cooktop installation and user guide Published: 09/2008 F&P Part No. 599575 A F&P Italy Part No. 1103208 - ß1...